-
product
High Voltage Switching Test System
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
product
Concrete Moisture Meter
7410
The electrodes transmit parallel low frequency signals, calibrated to give average moisture content by comparing the change in impedance between damp and acceptably dry concrete.Calibrated ready for use on concreteInstant readings on a clear, easy to read scaleFully portable, battery operated and non-destructive
-
product
GENASYS 75 Ohm RF Multiplexer Switch Card, (4) 2 x 16 Multiplexers
GX6864
The GX6864 consists of (4), 2 x 16, 75 RF switch configurations that can be used as multiplexers or matrices. The switch card is an extended 6U PXI module with direct connection to the receiver interface. The inputs to the switch multiplexers are accessed via dedicated external connectors located on the switch module. Additional connections are provided to the GENASYS' internal 16 wire bus for low frequency and self test applications.
-
product
Probes For Non-Contact Ultrasonic Testing
SONOSCAN CFC / CF
Due to the strong damping properties of air, low frequencies in the kHz range are used in air-coupled ultrasonic testing. It is therefore all the more important that the ultrasonic transducers offer a particularly high sensitivity in order to ensure high penetration and improved resolution. We achieve this, among other things, by installing preamplifiers in the receiver probe as well as by using our own Piezocomposite Technology, which enables a flexible use of the matching materials in our CFC and CF probes.
-
product
T3DSO Passive Probe, 350 MHz, 1X/10X, 1 MOhm/10 MOhm, 300V/600V
T3PP350
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Analog Seismic Sensors
Seismometers
Designed to yield the performance needed for scientific studies, our seismometers are used for monitoring long period (very low frequency) signals. These units are often used for earthquake monitoring and for triggering potential alerts during natural disasters such as tsunamis.
-
product
10:1, 10 Mohm, 300 MHz Passive Probe
PP016
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
HUM DETECTOR (DEMODULATOR)
HD-500
Matrix Test Equipment Incorporated
The MATRIX Model HD-500 is a detector-amplifier designed to demodulate the low frequency amplitude modulations on any RF carrier over the range of 5 to 1500 MHz. These modulations are usually the undesirable result of the 50 or 60 Hz power source and are not necessarily sinusoidal. The unit is calibrated to the SCTE definition of hum modulation, which is the ratio of the peak-to-peak hum modulation to the peak of the carrier.
-
product
Passive Probe
PP011-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
The Leading Measurement System for the Analysis of Porous Materials
ELWIS
ELWIS (Evaluation of Light Weight Impedance System) offers a full and rapid characterization of porous materials based on the analysis of a single sample. The ELWIS system consists of the ELWIS-A and ELWIS-S components which can be used independently from each other although both applications are needed for a complete material simulation.ELWIS-A measures acoustic parameters that are needed to evaluate the acoustic performance of sound insulation and sound-absorbing multi-layer materials. An additional impedance tube for absorption measurements at higher frequencies is available for ELWIS-A.ELWIS-S measures structural parameters that are needed to simulate the dynamic and acoustic behavior of sound packages in the medium to low frequency range (including the "Poisson Ratio" for foam materials).ELWIS is very easy to operate: Thanks to its user-friendly software, the system can also be used to obtain reliable results by users with only limited experience in the characterization of porous materials.
-
product
Low Noise Amplifiers
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
product
Compact Receiver Module
MixAMC-I
Virginia Diodes'' standard Spectrum Analyzer Extension Modules (SAXs) provide high performance broadband down-conversion and frequency extension of microwave specturm analyzers into the THz range. VDI now offers integrated MixAMC modules that provide industry leading performance in a compact package. These integrated MixAMC modules are used to down-convert millimeter-wave / THz signals only. Spectrum Analyzer Extension mode is not currently available for the MixAMC-I products. Integrated MixAMC modules utilize a low frequency LO input (<20 GHz) and have a seprate IF output port. Integrated MixAMC modules configured for high IF bandwidth may be available upon request.
-
product
Low-Mid Frequency Analyzer
LMFA-21
Amfax introduce the latest PXI based High Performance Low and Mid Frequency Analysis System operating from 100Hz TO 2MHz with an extremely low noise floor. This high accuracy measurement instrument utilizes the National Instruments Function Generator and Flex Digitizer to optimize your frequency related product performance. Using the industry standard PXI platform enables us to offer the system a fraction of the cost of other typical two box solutions.
-
product
Digital Combo Set for Measuring Low-Frequency Signals
SVG-5
- Measurement of root-mean-square AC voltage and frequency of single-ended or differential signals- Measurement of AC voltage frequency of single-ended or differential signals- Generation of sine waves- Visual examination of freeform signals- Signal spectrum analysis
-
product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP021-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
250 MHz Passive Probe for WaveSurfer3000, 10:1, 10 MOhm
PP019-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
SMP Connectors
Pasternack SMP connector (sub-miniature push-on connectors) category contains mostly RoHS and REACH compliant product varieties. The SMP connector category includes dozens of configurations including coaxial sub-miniature push-on connectors, PCB mounted, non-sealed and hermetically sealed terminals and shrouds. Our subminiature push-on SMP connectors are built to precise microwave and RF industry specifications and are part of over 40,000 in-stock RF products. Connectors in SMP series from Pasternack are manufactured in male or female gender with a 50 Ohm impedance. Pasternack's SMP subminiature connector are available in straight or right angle versions as well as bulkhead or mount-less options. These connector designs include solder or solder/solder attachment methods. Pasternack’s SMP connectors are miniaturized push-on interconnects commonly used in high density, blind-mate systems that can operate up to 40 GHz. Standard sub-miniature push on connector items are offered in a high frequency 40 GHz version as well as a low frequency 8 GHz version and are also available in smooth bore, limited detent and full detent styles. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMP connector series is in-stock. Not just in stock, these subminiature push on connectors will also ship the same day as they are purchased.
-
product
Ferrite Low Frequency Transducers
Ceramic magnetic design able to provide high-power handling and low distortion for the most demanding speaker manufacturers.
-
product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Very Compact Low-Frequency Control Element
750-LFC
The 750-LFC low-frequency-control element’s impressive power-to-size-ratio and versatile features make it the right choice for any application demanding superior low-frequency performance in low-profile systems. It pairs perfectly with ULTRA‑X40 and LINA systems, extending response down to 36 Hz for deeper, richer bass with total control.
-
product
Very Low Frequency Control Element
VLFC
Think extremely low. With a range of 13-30 Hz—the lowest reach of any Meyer Sound speaker—the VLFC extends below the threshold of human hearing to let your audience feel the sound like never before.
-
product
TimerBlox
Analog Devices TimerBlox parts are small, accurate, and simple timing devices designed for six basic operations: voltage controlled oscillation (VCO), low frequency clocking, pulse-width modulation (PWM), one-shot generation and signal delay, and power-on reset (POR). TimerBlox devices combine an accurate programmable oscillator with precision circuitry and logic. No capacitors, no crystals, no microcontroller, and no programming are required. A 20 mA source and sink capability enables the devices to directly drive opto-isolators and transformers for electrical isolation. An ideal solution for space-limited applications, each TimerBlox device can be placed at the point of use.
-
product
10:1 500 MHz 10 MOhms Passive Probe
PP005A
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MO. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Precision Capacitance Meter
TH2638A
Changzhou Tonghui Electronic Co., Ltd.
TH2638 series is a new precision capacitance meter with higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. With basic accuracy of ±0.07%, loss accuracy of 0.0005, test frequency up to 1MHz, 4.3-inch LCD screen, selectable Chinese-English operation interface, TH2638 series is easy to operate and provide fast and reliable test for ceramic capacitor production. Also, it can test all kinds of capacitors from low value to high value. The results of testing one capacitor for several times are quite stable and accurate, even for lower value capacitors. The tester is compatible with SCPI command set, and configured with manipulator and scanner interface, the scanner interface can scan the open/short/ load error calibration in each channel, 256 channels at most. In low frequency, there is signal level compensation function. When the impedance is very small, the internal resistance in signal source and test cable will cause the voltage on terminal of DUT lower than the set range, then this function will adjust the level to the set range.
-
product
Multibeam Profiler Sonar
MB1350-N
At 1.35 MHz, the MB1350 delivers 3D profile data at levels more akin to a laser line scanner than today' low frequency bathymentry systems. Mountable on Boats, ROVs, UUVs, and Tripods, BlueView's MB1350 is the right tool to take your operation into the next generation of 3D bottom and structure mapping.
-
product
RFID
LF (125 kHz)
BIS L uses a low frequency (LF) of 125 kHz with passive data carriers. These data carriers are read/write, designed for use in harsh environments and chemically highly resistant. With BIS L you can handle applications with special demands economically. Small form factors and versions with enhanced data security (additional check code) also provide great flexibility.
-
product
Low Noise Amplifier
DLNA8-40-50-2582
Low Noise Amplifier, Frequency 40~50GHz, Gain 38dB, Noise figure 3dB, P-1dB 13dBm, 1.85mm-Female Removable
-
product
Ultra Low Noise Preamp
J2180A
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
product
Power Dividers
We currently offer coaxial resistive power dividers (aka power splitters), which are inherently broadband and have excellent low frequency response (0!) albeit with poor isolation; and also Wilkinson Power dividers, aka Wilkinson Splitters. We have as connector options SMA, N, 1.95mm, & 2.92mm. Our power dividers cover DC-70Ghz. While most of our power dividers are 2-ways, we also have 3, 4, & 8 way dividers. The resistive power splitters are implemented with tiny resistors. Wilkinson splitters can be microstrip or stripline. RF Power Dividers are often lumped element, Microwave Power Dividers are often microstrip.
-
product
Linear Accelerometer Switch
Columbia Research Laboratories
Columbia Research Labs Accelerometer Switch is designed to interface with electrical or mechanical systems to control, safeguard against, or warn of undesirable variations in DC and low frequency acceleration. This sensor is available with a selectable switch point, a single or Bi-polar switch, and a choice of input power.
