RS-232
A standard interface for serial binary data interchange defining voltage levels for logical one and logical zero, standard transmission speed and connector types.
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
Interface RS-232
-
The RS-232 specification allows for reliable data transmission from one transmitter to one receiver at data rates of up to 20 kbps over relatively short distances (up to 50 feet). On more recent RS-232 transceiver chips, data rates of up to 1 Mbps are achievable over shorter distances (up to 5 feet). The most common applications for RS-232 transceivers are computers and peripherals, mobile phone data cables, and diagnostic data ports.
-
Product
- RS-232 DB9 Lightning Suppressor
Model 29
-
FEATURES: PC 386/486 Pentium Com Ports; Nanosecond Response; DB9 Connectors; Protects All 9 Lines; Ground Stud & Wire Included. The Model 29 contains avalanche diodes, one for each line. All diodes are returned to a ground stud. The Model 29 is provided with a 2-foot ground wire and has male and female DB9 connectors.
-
Product
Serial RS-232 Expansion Connector Accessory for USBHub3c
-
Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.
-
Product
RS-232/RS-485 Converter
ECD485
-
Deploy sub-metering sites and simple metering networks with ease using the EDMI MiniHub RS-232 to RS-485 converter.1/4 Load RS-485 modules allow for up to 128 devices over 1.2km of wired daisy-chain network, with each meter capable of becoming the Network Master and remotely connecting to a backhaul system via an integrated EDMI Modem Port redirect connector.
-
Product
PC/104-Plus And PCI-104 8-Port RS-232 Serial Communication
P104-COM232-8 and 104I-COM232-8
-
The P104-COM232-8 (PC/104-Plus) and 104I-COM232-8 (PCI-104) are PC/104-based eight channel RS-232 communication peripherals. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD). A 460Kb/s rate is guaranteed for all channels with up to 3K Ohm 1000pF loads. All interrupts may be monitored at a 32-bit status register. Each UART has both a 64 byte transmit and a 64 byte receive FIFO.
-
Product
RS-232 Line Driver with Control Signals and LCD Display
Model 224
-
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
Product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
-
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
Product
RS-232 Micro Line Driver - DB9 Connector
Model 209
-
FEATURES: Compatible with PC; 386/486 Pentium Com Ports; Full Duplex to 19.2 KBPS; No AC or DC Power; Screw Terminals or RJ-11; Small Size. The Model 209F offers all the features of the Model 201 Short Haul Modem but in a package that is approximately one third the volume.
-
Product
4 Serial Communication Channels, Programmable RS-232/422/485, Non-Isolated
SC6
-
Serial Communication Module SC6 provides up to 4 high-speed, programmable RS-232/422/485, individually non-isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel non-isolated returns are available as part of the channel user interface signal set (for SE or SYS-GND reference).
-
Product
PCI Express 16-Port RS-232 Serial Interface
7161e
-
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
Product
Serial (RS-232/422/485) Module for Multi Protocol 4000 Boards
-
Serial Module for Multi Protocol 4000 BoardsNOTE: The M4KSerial module is now a Legacy product. All new projects should use the M4KSerialPlus module (these modules are not compatible)
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 271
-
FEATURES: Full Duplex to 56 KBPS; 2 Kilometers on 62/125 Fiber; Total Electrical Isolation; Eliminates Noise Problems; ST Connectors; No Power Required. The Model 271 provides feature packed performance and reliability for data transmission over glass fiber.
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
- RS-232 to RS-422 Interface Converter
Model 263
-
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
Computer Interface, GPIB and RS-232
SR245
-
Stanford Research Systems, Inc.
The SR245 Computer Interface module is a powerful tool for data acquisition. It provides both an analog and a digital interface between your computer and your experiment.
-
Product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
-
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
-
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
- RS-232 to RS-485 2 Wire with LCD Display
Model 366
-
FEATURES: DataSpy® Status Display; Implements Low Cost LAN; Supports 32 Users; Uses Single Twisted Pair; External DTE/DCE Switch; Programmable Contention; Selectable Termination. The Model 366 allows interfacing RS-232 based equipment with networks/equipment using RS-485.
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
RS-232 Auto Powered Line Driver
Model 201
-
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
Product
- RS-232 to RS-422/RS-485 Concentrator - Wiring Hub
Model 290
-
FEATURES: Break RS-485 Limit, Expand to 496 Nodes 16 Port Capacity; Each Port Settable to RS-422 or 2 Wire RS-485; Provides Isolation Between Ports; All Ports Surge Protected; Increased System Reliability. The Model 290 RS-232 to RS-422/RS-485 Concentrator offers a unique group of features for those applications using RS-422 and/or RS-485 for communications between a multiplicity of devices.
-
Product
4 Serial Communication Channels, Programmable RS-232/422/485, Isolated
SC5
-
Serial Communication Module SC5 provides up to 4 high-speed, programmable RS-232/422/485, individually isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel isolated returns are available as part of the channel user interface signal set (for SE or ISO-GND reference).
-
Product
PCI-104 8-Port, 4-port, And 2-port Multi-Protocol RS-232, RS-422, RS-485 Serial Communication Boards
104i-COM-8SM Family
-
The 104i-COM-8SM (PCI-104) family of multi-port, multi-protocol (RS-232, RS-422, RS-485), serial communication boards deliver up to eight high-speed serial communication ports for use in a wide variety of applications. The boards were developed for use by system integrators and manufacturers in the design of industrial and commercial systems. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD) in RS-232 mode.
-
Product
- RS-232 High Speed Line Driver with LCD Display
Model 227
-
FEATURES: DataSpy Status Display; Full Duplex to 5 Miles; Async, DC to 115.2 KBPS; Powered by TD; RJ-11 and Screw Terminals for the Line Interface; Built-in Surge Protection; Fully Compatible with Model 201 up to 19.2 K. The Model 227 RS-232 High Speed Line Driver with LCD Display provides full-duplex transmission from DC to 115.2 KBPS over two twisted pairs.
-
Product
IDoor Module: 2-Ports Isolated RS-232 MPCIe, DB9
PCM-24D2R2
Expansion Module
Meets Advantech Standard iDoor TechnologyPCI Express® Mini Card Specification Revision 1.2 compliantSpeeds up to 921.6 kbps for extremely fast data transmissionSupports any baud rate setting (50bps~921.6kbps)Supports both Isolated & Non-Isolated Protection with 2/4 Ports RS-232/422/485Supports Thin Client Panel Computers TPC-xx51 seriesI/O address automatically assigned by PCIe plug & playOperating systems supported: Windows 2000/XP/Vista/7, and Linux 2.4/2.6OXPCIe952/OXPCIe954 UART with 128-byte FIFOs standardSupports Embedded Automation PC UNO-2200/2300/2400 seriesSupports Control DIN-Rail PC UNO-1200/1300/1400 seriesSupports Control Cabinet PC UNO-3200/3300/3400 seriesSupports Control Panel Computers TPC-xx81/xx82 series
-
Product
Isolated RS-232
-
Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.
-
Product
Single Port RS-232 Interface
PCI-COM232
-
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
Datalogging Light Meter (RS-232)
DLM 536
-
Spectrum of photo sensor meets C.I.E. photopic curve V(l). 16000 Records Data logging capacity. RS-232 interface (software included). Measurement of luminous intensity(PC Software)
