Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
product
Keysight Dual 4x16 Armature Matrix for 34980A
34932A
The Keysight 34932A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x16, 8x16, or 4x32 configurations 128 2-wire cross-points 300 V, 1 A switch; 2 A carry current Connections to the internal DMM Latching armature relays, with relay counter Expandable via four 2-wire analog buses
-
product
Computer-Based Instruments
GT210PXIe
With the GT210PXIe you can determine any frequency to 0.01 part per million (eight digits) in just 1 mS, and resolve each time measurement to 8pS. Couple that with 2300 measurements per second, one of the fastest rates available and you can acquire more data in a single second than a typical GPIB counter can in one minute! Faster measurements and higher resolution, along with built-in statistics functions give you a more thorough analysis of your signal. Standard deviation, peak to peak jitter, or a graph of the measurements are available at the push of a button.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
-
product
Mini Carbon Monoxide Gas Detector
Model - KM CO-910
Kusam Electrical Industries Limited
KM-CO-910 Carbon Monoxide meter detects the presence of Carbon Monoxide (CO) & measures concentrations between 1-1000 parts per million(PPM). The meter indicates the presence of CO by a reading on the LCD & a beeper tone. The beeper function much like clicking of a geiger counter: above 200PPM, the beeper sounds continuously with the concentration of CO; from 35PPM to 200PPM, the beeper sounds discontinuously with the concentration of CO.
-
product
Frequency Counters
Frequency Counters measure frequency, period, time interval, pulse width, duty cycle, frequency ratio, phase, and more. Frequency counter products include options that are compatible with Astronics/Racal VXI-2461C, which can be used for automated test aerospace and defense applications.
-
product
Isolated Programmable Multifunction Counter Board
APCI-1710
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Geiger Counters
A geiger counter detects nuclear radiation by measuring the emission of ionizing radiation of alpha particles, beta particles and gamma rays. Also referred to as a radiation detector, a geiger counter consists of two main elements: the processing electronics and the geiger tube. The geiger tube is filled with low-pressure inert gas like helium, argon or neon. If radioactive radiation occurs, the inert gas is ionized. An anode within the geiger tube registers the quantity of ionized particles numerically correlating with the strength of the radioactive radiation. The radioactivity measurement is then displayed on the LCD screen of the geiger counter or radiation detector.It is very important to measure radioactivity as well as to classify radioactivity values. For example, terrestrial gamma radiation is measured according to general values from 0.03 - 0.3 µSv/h (microsievert / hour). This "normal" oscillation range is conditioned by natural radioactive elements in the ground such as uranium and potassium. To calculate this factor, one must take into consideration cosmic radiation. For example, when considering cosmic radiation, the maximum radioactivity content at Schneefernerhaus, the highest-located German environmental research station, is approximately equal to 110 µSv/h.At PCE Instruments, you will find three types of geiger counter or raditation detection devices to help you measure radioactivity: 1) alpha radioactivity meters, 2) meters for detecting alpha, beta and gamma radioactivity and 3) radioactivity meters for human beings.
-
product
Sixteen Channel 12-Bit Analog Input/Output Cards
PCI-A12-16A
Model PCI-A12-16A is a multifunction, analog-to-digital, digital-to-analog, and digital I/O card. It accepts up to 16 single-ended inputs or eight differential inputs. Inputs are protected against over-voltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts. Conversions can be initiated in any one of three ways: (a) software command, (b) external start commands, or (c) on a timed basis using on-board programmable counters. Converted data may be transferred to the computer by one of two software selected methods: (a) polling for the end-of-conversion signal, or (b) by generating an Interrupt when the end-of-conversion signal occurs.
-
product
Isolated USB Digital I/O Modules (OEM Version Available)
USB-7230/7250
The USB-7230/7250 USB-based digital I/O modules feature high voltage on/off control and monitoring, and isolation voltage supported up to 2500VRMS. The USB-7230 provides 32-CH isolated digital I/O and 2-CH frequency/event counters. The USB-7250 provides 8-CH relay output (4 form C and 4 form A), 8-CH isolated DI, and 2-CH frequency/event counters. The USB-powered USB-7230/7250 features removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
product
PXI-6239, 8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779626-01
8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6239 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6239 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6239 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
PXI-6230, 8 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Hybrid, Multifunction I/O
779616-01
8 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6230 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6230 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6230 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
0.1Hz-3.7GHz Frequency Counter
FC-3000
Features:*Frequency measuring range: 0.1Hz to 100MHz in A input, 80 MHz to 3.0GHz in C input.*Period,Total and RPM measurement for input A*9 Digit display with 0.01mHz resolution in 1 Sec (By Ext.Reference signal).*RS-232C serial interface function for communication with computer.*High sensitivity Extemal reference input function(>=1.5Vrms).*Peciprocal technique for high resolution at low counting frequencies .*Self check function executed to perform a automatic self diagnosis of various counter function.*Push-scanning for selecting Function and Gate time.*Low-pass filter(100KHz,-3dB)installed for removing noise signsl in low frequency measuring.*AC/DC coupling function(Selectable AC/CD Coupling)*10:1 Input Attenuation(Selectable×1/×10 Attenuator)*Data hold function
-
product
Function Generator
FG-32
*6 FUNCTION,6RANGE.*LINEAR/LOG SWEEP*AUTORANGE COUNTER*0.001Hz RESOLUTION.*AUTO GATETIME.*COUNTER TRIGGER DETECT.
-
product
USB-6501, 24-Channel, 8.5 mA, Digital I/O Device
779205-01
The USB-6501 is a portable, bus-powered USB digital I/O device, providing reliable data acquisition and control at a low price. The device provides overvoltage protection its digital I/O lines and a 32-bit counter. With plug-and-play USB connectivity, the USB-6501 is simple enough for home and academic applications, but robust and versatile enough for laboratory and industrial applications.
-
product
Handheld Emission Particle Counter
HEPaC
Naneos Particle Solutions gmbh
*Simple measurement of particle number concentrations*Portable and battery-operated*Emission measurements without dilution (sensor heated)*Concentration range up to 5'000'000 particles/cm3*No operating fluids or dryers necessary*Automatic creation of an official measurement report on a tablet*METAS-certified according to ordinance SR 941.242
-
product
Electronic Warfare Solutions
Shoghi has a large portfolio of products under its category of Electronic Warfare. Traditional Electronic Warfare (EW) has three main elements of Electronic Support Measures (ESM), Electronic Counter Measures (ECM) and Electronic Counter Counter Measures (ECCM). Shoghi portfolio of products under EW are concentrated under the ESM and ECM umbrellas.The ESM products are passive means to monitor transmissions of various communication systems. Shoghi has covered these products in the numerous fields of satellite monitoring which covers both C/Ku band satellite monitoring, VSAT Monitoring, satellite phone monitoring under heads of Thuraya /Iridium / IsatPhone Monitoring, GSM/CDMA monitoring and Radio Monitoring using wideband scanning and multiple channel receivers. These are adequately covered under the head of Intelligence Surveillance and Reconnaissance (ISR) products.
-
product
Datalogging Software
XLog Datalogging Softwre
Laurel's data logging software can turn a PC connected to up to Laureate instruments into a powerful, data logging system. The Laureates can be any mix of digital panel meters, counters, timers and transmitters. The software allows 31 hardware instruments and 33 virtual instruments. The latter can display calculated parameters which combine data from multiple instruments.
-
product
Timer / Counter
The timer functionality is able to generate pulses or frequency signals with a defined number and duration.The counter function analyzes digital signals in terms of duration and number.
-
product
Electromagnetic Counters
ME Series
* Small, non-reset total counter * Low power consumption * Voltages:DC6V, DC12V, DC24V * Applications: fax machines, vending machines, printing machines, lease type machines, slot/game machines
-
product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
product
Mid Energy Counters
UEM1P5-4D R for RS485 Modbus RTU/ASCII communicationUEM1P5-D M for M-Bus communicationUEM1P5-4D E for Ethernet (Modbus TCP) communicationFor 1 or 5A CTProgrammable CT ratioFully bi-directional four quadrants measurements for all energies and powersFor 3 / 4 wire networks with balanced or unbalanced load (UEM1P5-4D R and UEM1P5-4D E only for 4 wire networks)Class B according to EN 50470-3S0 output for energy pulse emissionAvailable with MID certification
-
product
PMR Power Meter
The 3030 RF Power Meter is a modern version of the traditional Antenna Watt and VSWR instrument. The instrument cover communication bands from 30MHz to 500MHz. The 3030 RF Power Meter will measure forward and reflected power in the range from milliWatts up to 100Watts. Built in frequency counter. The counter will show the transmit frequency and will call the calibration table for the actual frequency. Outside the range of the counter the instrument can be set into manual mode giving a wider dynamic range. The 3030 RF Power Meter will calculate VSWR or Return Loss, and features Peak and Hold mode. Accessory kit with soft or hard carrying bag, car charger and coax adapters for standard types are available
-
product
Process Counters
TCT201-2ABC
The Process Counter TCT201-2ABC is a 1/16 Din 48 x 48 mm panel mount programmerable digital Counter with two 8 Amp relay outputs and up to 3 inputs. The TCT201-2ABC also has a potentiometer input that can accept either 5K or 10K Potentiometers. Other inputs can be PNP or NPN switches, 2 or 3 wire Proximity switches.
-
product
Colony Counter
Reichert Analytical Instruments
Full line of clinical instrument colony counters, handheld digital and analog.
-
product
Count Outside Micrometer
Mechanical counter type with 1/100mm resolution Measuring range: up to 250mm
-
product
Tachometers, Counters & Displays
Displays Include; Rate, Time In Process, Product, Sum, Difference, Ratio, Draw Process, Batch, or Total Counting. Field Adjustable, Full Diagnostic Functions. Built-In Relay Testing Capabilities. Highly Programmable. Single-Channel or Bi-Directional Counting. Setpoint and Start Delay Functions. Multiple Relay and Analog Output Options. Keypad Lockout
-
product
PXI High Resolution Waveform Digitizer Family
PXD730x
The PXD730x High Resolution Waveform Digitizer family features up to two 100MS/s simultaneously sampled input channels with 16Bit resolution, input voltages up to ±60V and a bandwidth up to 50MHz. Every digitizer channel has its own 2MB memory which allows up to 1 million samples. Data can be acquired before and after the trigger event with a programmable sample counter, that controls the number of data points.
-
product
Isolated Programmable Multifunction Counter Board
APCI-1710-10K20
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
