Audio Amplifiers
This topic is for test equipment that is designed for the testing of audio amplifiers.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
-
Product
2-Ch Sensor Amplifier
SR-2210
-
The SR-2210 sensor amplifier accepts constant-current line drive sensors and connects the signal to analyzers and recorders that would not otherwise be compatible with constant-current sensors.The units connects directly with BNC connectors to ONO's model MI-3111 microphone preamplifiers and NP-3000 series of accelerometers.With compact, light-weight, battery operation, it can save for preparation of measurement.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
High Voltage Amplifier
HA-400
-
*400Vp-p(±200V DC) *160mAp-p(±80mA DC) *Bandwidth: ≦600KHz(200Vp-p) *Slew Rate: 300V/us *Gain(AMPL): 0~90(10 Turn VR) *DC Offset: ≦0~±200V (10 Turn VR + SW) *Output Resistor: 50Ω
-
Product
2 GHz to 6 GHz, 25 W Power Amplifier Module
HMC7748
-
The HMC7748 is a multistage power amplifier (PA) that provides 25 W of saturated output power across the band of 2 GHz to 6 GHz. It draws 0.7 A from a 12 V supply and up to 4 A from a 28 V supply. Input signals of as much as −8 dBm are acceptable, and the module has small signal gain of 60 dB. The 12 V supply is regulated internally and generates the negative voltage required for the gate bias. Built-in bias sequencing prevents the drain voltages for the amplifier stages from being applied without the negative voltage present, which protects the amplifiers if 28 V is applied without 12 V supply applied.
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
3.5" Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, VGA/LVDS, Dual LANs And Audio
CAPA318
-
The CAPA318 features the Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake) with low power consumption. The integrated 3.5-inch embedded board is highly expandable and customizable. It comes with RS-232 ports, USB 3.0 ports, USB 2.0 ports, IN/OUT digital I/O ports, VGA port, LVDS port, and Gigabit Ethernet ports with Intel® i211AT Ethernet controller. For storage needs, the CAPA318 provides one SATA-600 socket and one mSATA interface. Additionally, Its compact and fanless design makes it perfect for use in space constricting environments. Additionally, the 3.5” single board computer can handle a wide operating temperature range from -20°C to +70°C (-4°F to +158°F) and requires +12V DC power input to ensure operational stability in a variety of harsh environments. This cost-effective 3.5” embedded motherboard is suitable for IoT/M2M related applications, industrial control, self-service terminals, digital signage, POS/kiosk displays, just name a few.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
DP Range Broadband Power Amplifiers 10 kHz - 250 MHz
DP Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 250 MHzTypical output power : 1000 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB>600 W and H<-20 dBcAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Cabinet on wheels3 years standard warranty
-
Product
Amplifier for the Frequency Range from 2 Hz to 50,000 Hz.s
Trig-Tek™ 203M
Amplifier
Versatile amplifier covers the frequency range from 2 Hz to 50,000 Hz.s and provides has three simultaneous outputs
-
Product
LINEAR AMPLIFIERS
F-series
-
The F-series amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance, very fast response and high current. The output is linear from DC up to few megahertz range.
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
Product
Air Amplifiers
-
Nex Flow® Air amplifiers are compact, low cost air flow “movers” that are virtually maintenance free. Applications include the venting of fumes and smoke, conveying of low weight materials, and entraining a high volume of air to cool, blow off, and dry. Air Amplfiiers use the “Coanda effect” to draw in the surrounding atmosphereic air while consuming only aminimal amount of compressed air. These products can amplify airflow up to 17 times (depending on the size) resulting in dramatcally reduced levels of noise. Air Amplifiers (also called Air Movers) draw in atmospheric air from the back of the unit as well as having downstream entrainment further amplifying the flow. They are used for cooling and venting. While the force produced for blow off decreases as the amplifier outlet diameter increases, these Air Movers are ideal for cooling because of the high velocity outlet fow and and are much more effective for cooling compaed to air nozzles.
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Variable Gain Optical Amplifier Module
VGA4700-FM06
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4700-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
Pico-ITX SBC With 4th/5th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, DisplayPort/LVDS, LAN And Audio
PICO880
-
The PICO880 is an extremely compact Pico-ITX SBC with onboard 14nm 5th generation Intel® Core™ i7/i5/i3 and Celeron® processors. The palm-sized PICO880 enhanced performance enables greater multitasking at low power meeting the needs of the growing retail mobile device marketplace. The industrial grade embedded SBC is built to withstand wide temperature conditions, ranging from -20°C to +70°C (-4°F to +158°F). Designed with expandability in mind, the tiny embedded board has a full-size PCI Express Mini Card slots with mSATA support. The Axiomtek PICO880 also provides two flexible board-to-board connectors that integrate audio, four USB 3.0, one PCIe x1, one DisplayPort, two UARTs, LED, and power on/off interfaces. The pico-ITX motherboard PICO880 is equipped with standard features such as one DDR3L SO-DIMM with up to 8 GB memory capacity; one USB 2.0 port; one SATA-600 interface, one 10/100/1000Mbps Ethernet port that supports Wake-on-LAN, PXE; one DisplayPort and LVDS display interface with integrated Intel® HD graphics 5500 and 6000 that delivers high-resolution Ultra HD 4K display support for immersive visual retail experience. The single board computer also offers two optional expansion boards, AX93275 and AX93276 for additional RS-232/422/485, USB 3.0, HDMI, VGA and LAN ports. This outstanding embedded SBC runs well with Windows® 7 and 8.1 operating systems.
-
Product
COM Express Type 10 Mini Application Board With LVDS, VGA, Dual LAN And Audio
CEB94018
-
*84 x 55 mini size form factor*2 GbE LAN*SATA and mSATA*LVDS and VGA*6 USB 2.0*2 PCI Express Mini Card slots
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
Low Noise Amplifier
-
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
Product
Audio MEMS Sensors
-
An audio MEMS sensor is an electro-acoustic transducer housing a sensor (MEMS) and an application-specific integrated circuit (ASIC) in a single package.
-
Product
Portable Power Amplifier
PA30Bip
-
PA30Bip portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
RF Tower Top Amplifiers and Receiver Multicouplers
-
Tower-Top Amplifiers (TTA) are high performance, quadrature-coupled low noise amplifiers (LNA) designed to increase the performance of a Base Transceiver Station (BTS) while ensuring reliable communications for critical Public Safety applications.
-
Product
VCOM Amplifiers And Calibrators
-
Renesas offers various VCOM amplifiers including rail-to-rail input-output operational amplifiers and rail-to-rail input-output buffers, as well as programmable VCOM calibrators that are ideal for display applications.
-
Product
Precision Amplifier
-
TI Precision Labs is the electronics industry's first comprehensive online classroom for analog engineers. The on-demand curriculum pairs theory and applied lab exercises to deepen the technical expertise of experienced engineers and accelerate the development of those early in their career. This free modular curriculum includes over 30 hands-on trainings and lab videos, covering analog amplifier design considerations with online course work.
-
Product
Monolithic Microwave Integrated Circuit (MMIC) Amplifiers & Switches
-
Microsemi's portfolio of MMIC products targets a broad range of applications including those in electronic warfare, radars, instrumentation (test and measurement) and microwave communications. The portfolio comprises broadband amplifiers (both power and low-noise), amplifier modules, prescalers, attenuators and switches spanning DC to 65GHz based on high-performance process technologies. Microsemi offers 18 distributed amplifier products including industry-leading DC-65GHz MMICs. Microsemi's prescalers combine higher frequency operation, the flexibility to divide by a large number of ratios and very good residual phase noise.
-
Product
Pico-ITX SBC With Intel® Pentium® N3710 & Celeron® N3060 Processor, HDMI (VGA)/LVDS, LAN And Audio
PICO300
-
The PICO300, an extreme-compact fanless pico-ITX motherboard, is built with the Intel® Pentium® N3710 or Celeron® N3060 processor (codename: Braswell SoC). One SO-DIMM socket is provided to support up to 8GB of DDR3L-1600 memory. The PICO300 is supported in dual display configurations along with one 18/24-bit single/dual-channel LVDS and a choice of VGA or HDMI. Furthermore, the tiny 2.5” pico-ITX embedded board features Intel® integrated Gfx graphic engine to build excellent media and graphics performance capability. In addition, the compact size of the pico-ITX form factor also makes the PICO300 suitable for space-constrained embedded applications. It runs fanless operation, and supports -20°C to +60°C operating temperature. Combined all features as above, the PICO300 is ideal for any media editing, imaging, graphics and video intensive applications that be applied for a wide array of industrial IoT industries.
-
Product
I/O Board With Two COM, Four USB 3.0 And Audio For PICO312, PICO313, PICO511, PICO512
AX93A02
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 1 x Audio (Mic-in/Line-in/Line-out), 4 x USB 3.0, 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
Product
Miniature Amplifier PCB
-
Sized for single channel TO-5 packages and electrically compatible with all Dexter Research Center detectors. Available in three amplifier gains: 300, 500 and 1,000 providing convenient buffering and pre-amplification of thermopile signal. Facilitates fast R&D startup time that can be integrated into your prototypes or final system design.
-
Product
Dayton Audio Test System
DATS V2
-
Highly accurate measurement of loudspeaker impedance and T/S parametersEasy-to-use, fully-featured measurement software with intuitive interfaceCompact USB measurement module with molded test leads and alligator clipsSoftware includes signal generator, scope, and measurement of inductors and capacitorsData can be saved to create a driver parameter library or exported to popular box design programsNew V2 hardware and software simplify setup and eliminate warm-up/cool-down times
-
