System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 472Ω
40-253-020
Programmable Resistor Module
The 40-253-020 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Testing Released Water Vapor
Humiditest™ Complete System
-
The James Instruments Humitest System allows the concrete practitioner to monitor and ensure that a new structure is dry enough to proceed with the next phase of construction. This is especially critical for concrete structures requiring a coating, carpeting or similar floor or covering treatment. Installing such treatments before the concrete is sufficiently dry will typically cause expensive failures in the covering treatment. The only accurate way to ensure that the concrete is sufficiently dry enough to safely avoid expensive re-work is via a bore hole humidity test system, such as the Humitest System
-
Product
Resistors
-
A passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.
-
Product
High Efficiency, Low-Cost Test for Less Complex Signal Devices
J750Ex-HD Family
-
Microcontroller Units (MCUs) are used in automobiles, mobile electronics and robotics. As you go through your day, dozens of MCUs are in your electronic devices working to provide unique features and Teradyne’s J750 family most likely tested them. With a growing installed base of over 6,000 test systems and widely available at more than 50 Outsourced Assembly and Test (OSAT) locations, Teradyne’s J750 is the industry standard for high volume test of low-cost devices.
-
Product
Meter Test Board
WECO 2150
-
Model 2150 automated test system is a fully ANSI compliant testboard that uses a single voltage and three independently controlled isolated current sources to test all electromechanical and solid state meters up to 50 Amps. Utilizing a precision laser optics system, the Model 2150 can test meters through the most grime-coated covers with unfailing accuracy. This same laser technology makes it possible to test using the disk’s edge without wasting time with the tricky optics adjustments found with other test systems.
-
Product
Meter Testing
METES
-
Meter test systems with high accuracies of up to 0.02% and a wide measuring range for precise measurements in single- and three-phase applications. The meter test systems of the METES series are used to test the accuracy of Ferraris meters and electronic electricity meters under any operating conditions. The impact of system perturbations such as harmonics or flicker on the meter can be taken into consideration during tests.
-
Product
Tensile/Compression/Bending/Torsion Testing Kits
-
With the constantly growing competitive pressure in today`s market are quality and product innovation basic requirements for any company.For this purpose TIRA is developing accurate and high quality material testing machines and testing systems which are manufactured according to the national and international standards DIN 5122, EN ISO 7500-1, GOST. With our testing machines you can carry out the static testing of metals, parts, wood, building materials, glass, plastics, fibers, composites etc.
-
Product
High-Precision Programmable DC Power Supply
MPS-3600H Series
-
MPS-3600 HSeries is a new generation of high-precision programmable DC power supply. This series of products is equipped with a standard communication interface, which has both desktop and system characteristics. It can be arbitrarily matched with other instruments and integrated into a special function test system to complete the measurement requirements in different occasions.
-
Product
PXI Precision Resistor Module 9-Channel, 1 to 31.5
40-297-110
Programmable Resistor Module
The 40-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 239Ω
40-251-013
Programmable Resistor Module
The 40-251-013 is a programmable resistor module with 8 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Motor Quality Control Test Systems
-
SKF Condition Monitoring Center
These rack-style motor quality control units are rugged, field-proven systems for testing stators and armatures in high-volume manufacturing environments. They combine the most common electrical tests into an efficient automated solution.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device
781630-07
GPIB Controller
Ethernet GPIB Instrument Control Device - The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Electrodynamic shakers
EV232
-
Labtone Test Equipment Co., LTD
Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.
-
Product
ESS Performance Test System
Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
Midirack - Installed Peripherals
OTP2-Modul-Nr044
-
The extension of the module can create new possibilities for your test system.
-
Product
Ionic Contamination Test Equipment
-
For manufacturers driven to deliver quality products, SCS Ionic Contamination Test Systems are the industry standard, delivering accuracy and performance in a range of configurations.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
Test System
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
Copper Diffusion TestSystems
-
Materials Development Corporation
MDC announces the addition of software and hardware for copper diffusion studies to its CSM/Win suite of semiconductor test systems and software. This new CSM/Win feature plays an important part in the development of processes and materials for the next advance in integrated circuit technology that employscopper as a conductor. Special Current-Voltage Bias-Temperature Stress (IV-BTS) software can measure the degradation of insulator quality due to copper diffusion.Multiple test sites can be stressed with a constant voltage while the current through each site is measured and recorded. The Current-Voltage Bias-Temperature Stress test supplements conventional MOS C-V measurements and Triangular Voltage Measurements (TVS) that are also employed in copper diffusion studies.
-
Product
Transformer Testing
-
Measuring bridges or electronic burdens can be individually integrated into existing CT/VT test systems. Customized solutions are our core competence.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω To 239Ω
50-297-013
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope
780319-01
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
External Frontend
FE50DTR
-
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
Product
Monitor / Annunciator
RTP-1
-
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
Product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
Matrix Switch Module
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
-
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
Product
PXIe Vector Network Analyzer, 300 kHz to 9 GHz
M9372A
Vector Network Analyzer
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
Product
Test Box
RF
-
This is a custom made part of a Phase Noise test system. It contains relays, filters, amplifiers, and so on. It works with other of-the-shelf eqipment, and custom software to form a high volume production test system.
