System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Connector and Breakout Box
ES4640
-
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
Product
Microcomputer Three-phase Relay Test Set
-
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations.
-
Product
Dual Channel 100 MHz Pulse Generator
PXIe-1209
Pulse Generator
The Astronics Test Systems PXIe-1209 PXI is a high-performance, 2-channel, 100 MHz Pulse Generator. Occupying a single PXI Express peripheral slot or hybrid slot, the PXIe-1209 provides dual independent pulse generation with fullcontrol of all timing parameters with extremely high resolution.
-
Product
System for Analyzing Door Handles
-
In the production process of a vehicle door handle, the electrical functions of the component are to be tested. The mechanical testing of the operation of the door handle is performed by a PLC-controlled test system. In addition to the mechanical test, the electrical parameters: “serial data stream” and “impedance of the antenna” are to be analysed.
-
Product
PXI 34x4 Signal Insertion and Monitor Matrix
40-525A-001
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also availablein a 16x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system. Each pass thru connection from LX to X can be open or closed to allow the programmatic disconnection of the signal to check the response of the UUT. The matrix can be used to connect test equipment, such as a DMM or scope, to monitor the pass thru signals via Y connections while the LY connections can be used to insert a fault condition or insert external signals. When external signals are injected the LX connections can be opened and the LY connections closed.
-
Product
AC Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 1.51MΩ
50-297-144
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 1.51MΩ
50-298-044
Programmable Resistor Module
The 50-298-044 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Solid State Versatile Multiplexer
40-682-002
Multiplexer Module
This versatile solid state multiplexer is especially useful where a high density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future. The PXI multiplexer uses high performance solid state switching to ensure a service life of greater than 10 years and fast operation.
-
Product
Automotive Test Systems
-
Ono Sokki Automotive Test Systems - flow meter, non-contact speedometer, engine tachometer, crank angle detector, and more
-
Product
Wireless Device Test
test
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
Product
Pattern Generator
S-113
-
The Pattern Generator slot module of FOTS system is an efficient module for the characterization and test of external optical components and systems to be performed in high bit rate. This module is a kind of pattern generator and bit error rate tester that can be used to modulate optical components or systems and to test the bit error rate characteristics of optical systems or optical lines. This pattern generator slot includes two differential Tx/Rx channels, which can be operated simultaneously.
-
Product
Sound Level Meter, 40 dB, 130 dB, 3.5 dB, 0.1 dB, 40 °C, 0 °C
72-935
-
The 72-935 is a Compact Digital Sound Level Meter, measures less than 6-inch length, including the windscreen and provides full 40 to 130dB measuring range. Perfect for numerous types of measurement including sound system testing and noise level monitoring.
-
Product
PXI Precision Resistor Module 4-Channel, 1.5 to 6.97k
40-297-124
Programmable Resistor Module
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
RMC-8355, 2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI
782568-01
External Controller
2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI - The RMC‑8355 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon E5620 quad‐core processors that support up to 96 GB of DDR3 RDIMM ECC RAM. The RMC‑8355 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8355 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
Product
Antenna Test Systems and OTA Chambers
-
With our well-established experience in innovative solutions based on top-quality engineering, Rohde & Schwarz provides you with leading antenna test systems and OTA chambers.
-
Product
VFTLP+ Test System
4012
-
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-251-114
Programmable Resistor Module
The 40-251-114 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 1.51MΩ
40-298-050
Programmable Resistor Module
The 40-298-150 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXIe-2737, 256-Crosspoint, 4x64, 2-Wire PXI Matrix Switch Module
782835-37
Matrix Switch Module
256-Crosspoint, 4x64, 2-Wire PXI Matrix Switch Module—The PXIe‑2737 is a high‐density 4x64 PXI matrix switch module designed for routing signals within automated test systems and using electromechanical relays to perform immediate switch operations. It also offers features to monitor the health of deployed systems and plan for predictive maintenance, including onboard relay count tracking, a temperature sensor, and functional and resistive relay self-tests available through the NI Switch Health Center.
-
Product
PCM Generator
MS 1607
-
The PCM Generator System used to generate different types of PCM format signals. The user can configure the PCM format to be generated. This system is an independent unit with LCD and Keypad for user interface. Primary application of the system lies in testing the airborne equipment.
-
Product
Rail Traction Inverter Test System
-
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
Product
Cellular Base Station Factory Test Systems
-
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
Product
Test & Measurement Automation Services
-
Our flexible and collaborative approach delivers efficient, accurate, and robust test systems, as well as the tools to leverage test data for effective results analysis. We develop systems using a variety of software and hardware platforms (custom and off-the-shelf), data acquisition systems, and control methods. We are comfortable developing custom turnkey systems or working alongside your team on your current system under development.
-
Product
microLED Testing System
OmniPix-ML1000
-
The OmniPix-ML1000 is the first all-encompassing microLED testing system, offering both full wafer and localized individual pixel inspection. Measure localized and total EQE. Use automated PL and EL to test and characterize your microLEDs. Analyze defective pixels with nano-PL and nano-EL.
-
Product
Pass-by Noise System
-
Vehicle Pass-by Noise TestingA very flexible Pass-by noise test system for characterizing the overall acoustic signature of any vehicle. Our solution brings a simpler, more effective and cheaper way to obtain accurate velocity and acceleration results for the Pass-by Noise test.
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Digital Oscilloscope
DS8000-R
-
DS8000-R series digital oscilloscope is a compact mid-to-high-end digital oscilloscope based on RIGOL's UltraVision II platform. With a compact design, DS8000-R supports multi-machine system integration, suitable for rack installation. It also allows remote control, and meet the standards of industrial automation test systems.
-
Product
PXIe-5451, 145 MHz, 16-Bit, 2 GB PXI Waveform Generator
781204-03
Waveform Generator
PXIe, 145 MHz, 16-Bit, 2 GB PXI Waveform Generator—The PXIe‑5451 is a 145 MHz, dual‐channel arbitrary waveform generator capable of generating user-definied waveforms, standard functions, and I/Q communications signals. It is an ideal instrument for including in systems for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator as wells as time-domain signals like envelope tracking. The PXIe‑5451 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5451 also features advanced synchronization and data streaming capabilities.
-
Product
Full 4-Quadrant Grid Simulator
TC.ACS
-
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
