Product

Primary Standards

-

Mensor Corp.

Mensor Corp.

Primary standards (often also referred to as mechanical dead-weight testers, pressure balances or primary pressure standards) are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the primary standard an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port which measured through piston gauge technology.

Product

Standard

-

Quartzlock (UK) Ltd.

Quartzlock (UK) Ltd.

RF Distribution Amplifiers

Product

2210A & 2211A Quartz Frequency Standards

-

Precise Time and Frequency, Inc.

Precise Time and Frequency, Inc.

The ptf 2210A Quartz Frequency Standard has been designed to provide a highly stable and spectrally pure frequency reference for applications requiring the ultimate in short term frequency performance.The instrument contains a double oven controlled stress compensated (SC cut) quartz crystal oscillator (OCXO) to give the ultimate in performance.Ideal for laboratory or system use, the unit provides good stability performance at lower cost and with improved phase noise.

Product

Standard DIP Socket with Solder Tail Bifurcated Contacts

Series 511

-

Aries

Series 511 - Aries

Standard DIP Sockets with Wire Wrap Bifurcated Contacts. Features: Standard DIP sockets are available with solder tail or wire wrap pins, all with bifurcated contacts. Consult Data Sheet No. 12005 for wire wrap pins. Aries offers these standard DIP sockets in more sizes than any other manufacturer.

Product

Global Standard Model For 4 Point Probe Sheet Resistance Automatic Measurement System

RT-3000/RG-1000F

-

NAPSON Corp.

RT-3000/RG-1000F - NAPSON Corp.

*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software

Product

Standard Ratio Box For Calibration

ST-105

-

Raytech AG

ST-105 - Raytech AG

The ST-105 is a calibration box with standard ratios. It is used for calibration of any turn ratios measurement system. Housed in a rugged, waterproof case, it is very lightweight.

Product

IEC60335 Standard Electrical Temperature Tester

CX-w15

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-w15 - Shenzhen Chuangxin Instruments Co., Ltd.

Standard Test corner/room conform to IEC60335-1:2004. and GB4706.1-2005. can be used to the temperaturetest of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.

Product

600MM 24In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles, IP54 Standards

DL406

-

Advance Plus Trading Co., Ltd.

DL406 - Advance Plus Trading Co., Ltd.

Model Number: DL406 Key Specifications/Special Features: 600MM 24INCH Digital Level with level bubbles,LCD bright backlight display, IP54 standards 1. 600mm 24 inch level with 2 bubbles, 600*28*64mm（L*W*H）, net weight: 520g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13.Handshank design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.

Product

Temperature Stabilized Resistance Standards

-

Measurements International Ltd.

Measurements International Ltd.

The temperature stabilized resistance standards offer customers the very best in accuracy, and stability. With 3 different models to choose from, covering the full range of resistance values.

Product

GFS Primary Gravimetric Flow Standard

-

Fluke Calibration

Fluke Calibration

The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.