-
Product
PCI Direct Digital Synthesizers
SYNTH300 SERIES
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.Software support for Windows Vista, Windows XP,Linux and Labview source code availableFor detailed specifications, please refer to the Synth300_Manual
-
Product
PXI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module
778967-01
Digital I/O
64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PXI‑6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-022
Programmable Resistor Modules
The 40-254-022 (PXI) and 42-254-022 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Programmable Gain Amplifiers
-
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 1.51MΩ
40-251-044
Programmable Resistor Modules
The 40-251-044 is a programmable resistor module with 2 channels which can be set between 2.5Ω and 1.51MΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Compact USB Programmer
S6
-
The Dataman S6 is a USB powered universal 48-pin programmer with compact dimensions and minimal weight • USB powered - no additional power supply is required • Over 16,000 devices supported with new devices added monthly • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Multiprogramming support allows one PC to control up to eight units programming as a gang programmer • Comprehensive 3 years parts and warranty • Free life-time software updates
-
Product
Temperature Monitor
SIM922A
-
Stanford Research Systems, Inc.
The SIM922A has a programmable, precision 10 µA current source to provide sensor excitation. Results can be displayed in either kelvins or volts.
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
Programmable DC Current Source
Model 121
-
The Model 121 programmable DC current source is a precision instrument suitable for bench-top use or panel-mounted operation in labs, test facilities, and manufacturing environments. It provides a low-noise, highly stable source of current up to 100 mA, with convenient manual selection through 13 pre-set output levels, each representing a ten-fold change in power when attached to a resistive load. A “user” setting allows the current output to be defined anywhere within the operating range of the unit, from 100 nA to 100 mA.
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 9 W, PXI Programmable Power Supply
779647-10
Programmable Power Supply
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
Probe Card
Indexer™
-
The patented Indexer™ is the industry’s first automatic probe card changer designed for lights out parametric test.*Can support up to five VC20™’s with Advanced Cantilever™ technology, any variety*Card changes are complete in seconds*Fully programmable*Tested for hundreds of thousands of touchdowns.
-
Product
Power Supply Support
-
Renesas offers a complete portfolio of system supervisory solutions ranging from single to quintuple (five) voltage monitors. In addition, the system management ICs are voltage monitors with small amounts of I2C or SPI software programmable EEPROM memory. Renesas single-chip sequencing solutions sequence up to four different voltages while providing other useful features such as voltage monitoring, fault protection, and reset assertion.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-152
Programmable Resistor Modules
The 40-297A-152 (PXI) and the 42-297A-152 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Military-Grade 4-In-One Temp/Humidity/Vibration/Pressure Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Integral structure, the internal overall TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism. - The use of Chinese color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box independently developed special software, with automatic, intelligent, human control and other characteristics. - Control mode: constant operation mode, program operation mode. - TEST EQ patent "Cold and heat balance technology”, low temperature constant temperature season can be more than 30%. - Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions. - The humidification system adopts TEST EQ patented technology. - The lift structure through the lift (wireless remote control) up and down and left and right movement to match the shaking table horizontal or vertical table, comprehensive performance test. - Gantry structure: Through worm gear (wireless remote control), the studio box is lifted up and down and the gantry is moved around to match the horizontal or vertical table of the shaking table, and the comprehensive performance is tested. - The seal of temperature and humidity box and vibration table adopts TESTEQ patent technology low pressure flexible connection device. - Pressure mode: internal pressure type or external pressure type. - Vacuum system: the world famous brand ""Laibao"" or ""Jitis"". - Configure RJ45 communication interface, remote control system (open data transmission protocol support Modbus/OPC). - Surface electrostatic powder spraying; chamber color ""TESTEQ White "", controller panel color ""TESTEQ Blue "".- TESTEQ patent cold well adsorption anti-condensation function (optional).
-
Product
P104 LVDT/RVDT Measurement Board
73LD4
-
NAI’s 73LD4 is a PC104-compliant LVDT/RVDT Measurement Board with six separate transformer-isolated channels. The channels can incorporate up to six programmable LVDT/RVDT-to-Digital Tracking Converters in a stack-through module. Each channel is programmable for 2-, 3-, or 4-wire inputs that automatically range between 2.0 volts and 28 volts, so there is no need to purchase multiple boards set for specific inputs. Operating frequency between 360 Hz and 10 kHz can be specified. Each channel also produces differential incremental encoder (A & B) outputs with programmable resolution and a zero-degree marker pulse.
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P, LL/UL/S/C, Programmable Amplitude Balance
LS-16A-R1-24SPLUSC
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
MIL-STD-1553 A / B Test And Simulation 3U PXI Module
PXI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*PXI trigger on 1553 bus events*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
PMC Module
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
Product
Programmable Step Attenuator, DC to 50 GHz, 0 to 65 dB, 5 dB steps
84908M
Attenuator
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
Product
Fixed Systems
-
Low cost versatile solutionCompact, weatherproof, NEMA 4X enclosure115/220 VAC or 24 VDC operationLong life sensors (2+ years typical)Accepts RKI LEL/O2/H2S/CO direct connect sensorsAccepts any 4-20 mA transmitterAudible alarm with reset buttonTwo programmable alarm levelsBuilt-in trouble alarm with relayRelay rating 10 amps, form CProvides 4-20 mA output
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 3U VPX
Model 52671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- Extended interpolation range from 2x to 1,048,576x- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (Open VPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Indicators & Displays
-
30,000 displayed divisionsOIML R76 ApprovedStainless steel IP65 housingMains powered with 12V DC option25mm wide angle LCD display with back light2 programmable function keys and navigation keys provide easy operationLinearity correctionGravity AdjustmentLi-Ion long life rechargeable batteryAuto Power offPanel mount, desk stand, pole/wall bracket mounting includedRS-232C data port standard, 2nd RS-232C port optionTicket printing with Date, Time, Ticket no, Gross, Tare & Net Weight100 product memories for check weighing and countingSmart dynamic weighing algorithm for animal weighingCE approved
-
Product
QuadPOD Conditioning Interface
JT 2147/VPC
-
The JT 2147/VPC is a variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within Virginia Panel Corporation’s mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry, two independent, programmable TAP modules (of type JT 2149) and two TAP modules with I/O (of type JT 2149/MPV) on a single board that interfaces via the VPC QuadraPaddle connectors type G20x or G14x.
-
Product
Controllers
-
*Inputs for analog, digital, diagnostic and pulse signals*Digital, PWM or current-controlled outputs*Programmable to IEC 61131-3 with CODESYS*High-performance CAN interface for various communication tasks*E1 type approval (German Federal Motor Transport Authority)
-
Product
Power Quality Meter
PQMII
-
The PQM II is an ideal choice when continuous monitoring of a three phase system is required. It provides metering for current, voltage, real and reactive power, energy use, cost of power, power factor and frequency. Programmable setpoints and 4 assignable output relays allow control functions to be added for specific applications.
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 57671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-036
Precision Resistor Module
The 40-297A-036 (PXI) and the 42-297A-036 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 395 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Programmable DC-DC Converter
VDD Series
-
VDD series is a high power and variable output DC-DC converter which can be operated on DC. Because the DC operation, VDD is most suitable for many applications. For example, it is the best choice for R&D of next-generation energy systems and anti-disaster measure systems, such as Smart house in which electricity is supplied as DC mutually between home rechargeable batteries and EVs, and Voltage adjustment when driving DC electronic equipment by emergency large rechargeable batteries.
-
Product
8-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 58671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 1.25 GHz 16-bit D/As- Eight digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Quad µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 26.7kΩ
40-251-032
Programmable Resistor Modules
The 40-251-032 is a programmable resistor module with 4 channels which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
