-
Product
Temperature & Humidity Sensor Breakout Board
Si7021
-
Sensor for Silicon labs has ± 3% relative humidity measurements with a range of 0–80% RH, and ±0.4 °C temperature accuracy at a range of -10 to +85 °C. Great for all of your environmental sensing projects. It uses I2C for data transfer so it works with a wide range of microcontrollers.
-
Product
Development Platform
LaunchPad™
-
Begin rapid prototyping applications in minutes with our microcontroller-based LaunchPad kits, Sitara™-processor-powered BeagleBoards and SimpleLink™ wireless connectivity SensorTags. The Sidekick line of kits from Seeedstudio offer customers a quick way to evaluate custom circuits with many of the popular microcontroller development kits available on the market.
-
Product
Circuit Simulation & PCB Design Software
TINA Design Suite
-
TINA Design Suite s a powerful yet affordable circuit simulation and PCB design software package for analyzing, designing, and real time testing of analog, digital, HDL, MCU, and mixed electronic circuits and their PCB layouts. You can also analyze SMPS, RF, communication, and optoelectronic circuits; generate and debug MCU code using the integrated flowchart tool; and test microcontroller applications in a mixed circuit environment.
-
Product
SparkFun 16 Output I/O Expander Breakout
SX1509
-
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
Product
Absolute Optical Encoder
A2
-
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
SPI Isolators
-
SPI (Serial peripheral interface) is one of the most widely used interfaces between microcontrollers and peripheral ICs such as sensors, ADCs, DACs, shift registers, SRAM, and others. Analog Devices has your isolated SPI bus covered with our dedicated SPI digital isolators which support this synchronous, full duplex master-slave-based interface. Options include devices built with ADI's proven iCoupler® technology and offering a small footprint, simple design-in, fast speeds, and high data integrity, as well as integrated µModules which require no external components. Our SPI isolator solutions increase performance and reduce board space. This simple, compact solution is ideal for isolated SPI data requiring communication across different ground potentials or through large common mode transients often found in Industrial PLCs (programmable logic controllers) and Instrumentation and data acquisition systems.
-
Product
High Parallel Tri-Temp Pick-and-Place Handler
Delta MATRiX
-
Cohu’s MATRiX handler has a highly flexible test site configuration that’s well suited for a wide range of test applications, including analog ICs with short test times and high throughput, automotive devices requiring accurate thermal control, small pitch wireless-communication products, high parallel microcontroller testing, MEMS device testing, and many other device market segments with their unique requirements. The MATRiX has a highly flexible test site configuration that enables customers to reuse existing load-boards, including boards made for competitor’s legacy handlers.
-
Product
Intelligent Sensors
-
Silicon Labs is a leading supplier of intelligent sensor solutions that are characterized by superb reliability, compact size, high levels of integration and unmatched ease of use for a variety of applications. Our diverse sensor product portfolio includes optical sensors, digital relative I2C humidity and temperature sensor ICs, biometric sensors and capacitive touch sense microcontroller devices.
-
Product
RX Family Of 32-bit High Power Efficiency MCUs
RX600
-
The RX600 Series has an abundant lineup of high-performance microcontrollers with up to 160MHz CPU operation, This Series offers up to 4MB of embedded Flash and 640KB of embedded SRAM, advanced security, connectivity (Ethernet, USB, CAN) and HMI function. The RX600 Series addresses a broad range of applications for IoT endpoints such as white goods, meters, and other industry and consumer area. The RX600 Series can be considered as the mainstream series of the RX Family. Some of the RX600 Series products are tuned for motor control solutions, too.
-
Product
Renesas Synergy™ Microcontrollers
-
Spanning across four distinct series, the Renesas Synergy™ Microcontroller family is designed for end applications ranging from connected mobile devices for the IoT market to high-performance embedded systems controllers.
-
Product
Triple-Axis Accelerometer (+-2g/4g/8g/16g) w/ I2C/SPI
ADXL345
-
Filling out our accelerometer offerings, we now have the really lovely digital ADXL345 from Analog Devices, a triple-axis accelerometer with digital I2C and SPI interface breakout. We added an on-board 3.3V regulator and logic-level shifting circuitry, making it a perfect choice for interfacing with any 3V or 5V microcontroller such as the Arduino.
-
Product
Low Cost Emulator
EB-XAG49
-
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
Development System
FE-W7
-
* Emulates Winbond W77xxx or W78xxx Microcontrollers * 125K Code Memory * Real-Time Emulation * Frequency up to fmax at 1.8V to 5.5V * Wide Supply Voltage Support * MS-Windows Debugger For C And Assembler * Emulation Headers for PLCC, QFP and DIP * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Multifunction Meters
-
Measures V, A, PF, Hz, KW, KVA, KVAr, Kwh, KVAh & KVArhTRMS MeasurementCan be used for Continuous MonitoringAuto / Manual Scroll Display (User Selectable)State of Art Microcontroller DesignPortable, Handy, Plug-n-Play and Easy-to-useLCD Display with BacklightRS-485 5KV Isolated Port (Optional) with MODBUS RTU Protocol (Optional)POWER MASTER Software for MIS Reports (Optional)
-
Product
Microcontrollers And Microprocessors
-
In response to user requirements that are rapidly expanding in scope, Renesas Electronics offers microcontroller and microprocessor products that provide excellent expandability while allowing customers to make full use of existing resources.
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
Low Cost Emulator
EB-XAS3
-
* Emulates P51XAS3x Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 68-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
RL78 Family of 8/16-bit Ultra-Low Energy MCUs
RL78/I1x
-
The RL78/I1x microcontrollers are part of the RL78 microcontroller family with rich analog integration and support high temperature operation. RL78/I1x is ideal for application specific solutions but also suitable for many general purpose application In the mass market with tough environment operation.
-
Product
Custom And ODM Designs
-
Added intelligence in the form of custom firmware, FPGA design and microcontroller code add product feature for differentiation in the market.
-
Product
SparkFun SAMD21 Development Board
RedBoard Turbo
-
If you’re ready to step up your Arduino game from older 8-bit/16MHz microcontrollers, the SparkFun RedBoard Turbo is a formidable alternative. At its heart, the RedBoard Turbo uses the ATSAMD21G18, which is an ARM Cortex M0+, 32-bit microcontroller that can run at up to 48MHz. With an impressive 4MB of external flash memory and a UF2 (USB Flashing Format) bootloader, the RedBoard Turbo provides you with an economical and easy to use development platform if you're needing more power than the classic RedBoard.
-
Product
Microcontrollers
-
Panasonic Industrial Devices Sales Company of America
Based on a rigorous analysis of embedded device software and system needs, the Panasonic AM1 (MN101C/MN101E/MN101L) and AM3 (MN103H/MN103S/ MN103L) Series signal a new concept in Microcomputer design. With 8-bit and 32-bit models that share a unified architecture, Panasonic Microcomputers combine high performance with low power consumption in a package that supports C-language programming for a fast, efficient development cycle. Since the instructions for MN103H/MN103S and MN101C/MN101E are respectively compatible with MN103L's and MN101L's, the programming data can be inherited to achieve efficient system development. Panasonic Microcomputers feature a single development environment and are suitable for a wide range of applications, including high-performance embedded controllers and key devices in multimedia hardware.
-
Product
WriteNow! Programmers
-
Based on the proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices (microcontrollers, memories, CPLDs and other programmable devices) from various manufacturers and have a compact size for easy ATE/fixture integration. They work in standalone or connected to a host PC (RS-232, LAN and USB connections are built-in), and are provided with easy-to-use software utilities.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
In-Circuit Programmer/Loader
SKU-018-01
-
The In-Circuit Programmer/Loader (“EasyLoader” or “eLoader”) is a standalone device that was designed to provide a flexible and cost-effective solution for electronic device manufacturers, as well as for hardware design companies and their customers. It allows you to upgrade code on any JTAG/SPI/I2C compliant device (like FPGA/CPLD/EEprom/Flash, etc.) or Microcontrollers at any time of development, testing or production.
-
Product
Integration of Flash / Controller Programming
-
Flash or microcontroller programming can be integrated in a wide variety of ways, depending on the type and scope of the application.
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
SPC5 32-bit Automotive MCUs
-
The SPC5 family of 32-bit Automotive Microcontrollers is designed to accommodate a wide range of automotive applications ranging from Gateways, Electro Mobility, and ADAS to Engine and Transmission control, Body, Chassis and Safety. Based on a Power PC Architecture, SPC5 microcontrollers provide up to 3 cores operating at up to 200 MHz and with a 165 °C junction temperature.
-
Product
Semiconductor Testing
-
Teradyne’s semiconductor test portfolio is transforming the way you test chipsets for automotive, industrial, communications, consumer, smartphones, and computer and electronic game applications. Semiconductor devices span a broad range of functionality, from very simple low-cost devices such as appliance microcontrollers, operational amplifiers or voltage regulators to complex digital signal processors and microprocessors as well as memory devices.
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
