-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
ABex in System Programmer with Onboard SMH FlashRunner LAN 2.0 NXG
ABex AM-307 FR-NXG Flashrunner
-
The ABex AM-FR-NXG incorporates the FlashRunner LAN 2.0 Next Generation from SMH Technologies. The FlashRunner is used to program microcontrollers, flash and other logic and memory devices. All DIO’s, the programmable voltage lines and the corresponding ground lines can be switched by relays.The ABex AM-FR-NXG is equipped with an onboard Ethernet Controller which connects the FlashRunner directly to the PXIe Backplane of the ABex Chassis. Using a windows host, each AM-FR-NXG will provide its own network adapter.
-
Product
LED Drivers And Backlighting
-
Simplify the development of LED applications and get to market faster with our complete portfolio of LED drivers, which can be combined with our microcontrollers and power management, interface and connectivity products.
-
Product
5-Position Switch
27801
-
The 5-Position Switch is a normally open contact switch. It has a nice snappy feel, and returns to the center/un-pressed position immediately when it is released. By monitoring the input state of five pins, it’s easy for any Parallax microcontroller to detect whether the switch is in the up, down, left, right, or pressed position. It is possible for more than one position to make contact at a time, such as pressed+right, left+down, or pressed+right+down, for a total of 18 output states.
-
Product
TSL1401 Linescan Sensor Daughterboard
28317
-
The Parallax TSL1401 Linescan Imaging Daughterboard provides one-dimensional sight to almost any microcontroller. It is designed for plug-in compatibility with Parallax’s BS2pe Motherboard but can be used with other BASIC Stamp modules, the Parallax Propeller, the SX, PICs, and AVRs, to name just a few. It is a platform suitable not only for evaluating TAOS’s TSL1401R imaging chip, but also for incorporation into OEM products, as well as hobbyist, robotic, and educational platforms.
-
Product
LilyPad Light Sensor
-
The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from the board through the signal tab to the microcontroller you connect the sensor to. If the sensor receives no light, no current will flow through it. In a typical indoor lighting situation, the sensor will output around 1 to 2V. Adding this board into your next e-textile or wearable project will really open up the possibilities by being able to incorporate light level sensing capabilities.
-
Product
Low pin and internal configurable analog MCU
RL78/G11
-
The RL78/G11 microcontroller line-up concept is based on small packages like 20 to 25pin, in small 16KB flash memory and rich analog peripherals such as A/D converters, D/A converters, comparators and PGA and these are configurable as PGA+ADC+VBGR, PGA+CMP, CMP+DAC/VBGR, or PGA+CMP+DAC/VBGR. Using the smart features like DTC and ELC a lot of peripherals can be connected internally to reduce CPU workload and can save overall power consumption. It also supports very low power operation (100 uA @ 1 MHz ) and a high speed 4µs wake up. Available in small 3x3mm² WFLGA , 4x4mm² HWQFN and standard 20pin LSSOP, this MCU line is suitable for sensor application, Lighting/power sources and many small appliances.
-
Product
In-Circuit Debugger for RS08 Family of Microcontrollers
ICDRS08
-
P&E's ICDRS08 is a powerful tool for debugging code. It uses the processor's background debug mode Module(BDM), via any of P&E's RS08 compatible interfaces (see product add-ons for more information), to give the user access to all on-chip resources.
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
Circuit Simulation Software
-
Proteus Virtual System Modelling (VSM) blends mixed-mode SPICE simulation with world leading fast microcontroller simulation. It enables rapid prototyping of both hardware and firmware designs, in software! Design, Test and Debug your embedded projects in the Proteus electronic circuit simulator before a physical prototype is ordered. Agile development for the embedded systems workflow.
-
Product
Cross Development Tools
S12Z
-
Cosmic's tool chain for the S12Z family is part of a complete and uniform product line incorporating over 20 years of innovative design and development. Cosmic's familiar and easy to use software interface is available for all Freescale microcontrollers to simplify the migration between targets. All Cosmic products include one year of technical support and updates.
-
Product
Orange5 Programmer
-
Orange 5 is a professional tool for programming memory and microcontroller. A unique feature of the current generation of programmers is built macrolanguage the preparation of records. It enables the addition of new types of micro patterns, meeting the requirements of manufacturers’ read and write algorithms
-
Product
ESP8266 WiFi With Headers
Feather HUZZAH
-
Flagship development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Assembled Adafruit Feather HUZZAH ESP8266 with headers. At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core.
