Isolation Amplifiers
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
-
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
64-CH Isolated Digital I/O Modules
cPCI-7432/7433/7434
-
- Two external interrupt sources for cPCI-7432/7432RP/7433- 3U Eurocard form factor, CompactPCI compliant (PICMG 2.0 R2.1)- 32-CH isolated digital inputs & 32-CH isolated digital outputs for cPCI-7432- 64-CH isolated digital inputs for cPCI-7433- 64-CH isolated digital outputs for cPCI-7434/7434P- 5000 VRMS isolation voltage
-
Product
Low Noise High Precision High Voltage Amplifier
WMA-280
-
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
Product
CATV Separate Raman Amplifier
RFA4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Amplifier is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. Raman amplifier is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Amplifier Systems
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies.
-
Product
Dual Channel High Voltage Linear Amplifier
F1020
-
This unit contains two independent amplifiers that share common ground reference and power supply. Left channel correspond to the F10A model and right channle corresponds to the F20A model.
-
Product
ULI-344DC - USB To RS-232/422/485 (DB9 Male) Industrial Isolated Converter, 4 Port
BB-USR604
-
USB to RS-R32/422/485 ConverterUL Class 1/Division 22 kV IsolationLevel 4 ESD Protection (15 kV Air, 8 kV Contact)921.6 Kbps Serial Data Rate- 40 to + 80 °C Operating TemperatureDIN and Flat Panel Mounting OptionsTB and Power Jack 10-30 VDC Power InputsHigh Retention USB Connector, Plug in Serial Terminal Block
-
Product
MOSFETs For Amplifier
-
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
Product
Isolated Relay I/O Card
mPCIe-IIRO-8
-
The mPCIe-IIRO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 750 V Isolation
43-752A-011
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
YDFA Amplifier
-
a high-gain three staged polarization maintaining optical amplifier unit designed for applications requiring high efficiency optical amplification in the 1060 nm regime in both CW and pulse mode operations.
-
-
Product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Product
Miniature Single-Stage Isolators – 780nm And 852nm
-
AOSense is excited to offer free-space optical isolators at 780 nm and 852 nm. The innovative, small package size enables integration into compact laser sources and amplifiers without sacrificing transmission efficiency. The low external magnetic field enables the isolator to tightly integrate into systems with high magnetic-field sensitivity such as atomic spectrometers, magnetometers, clocks, and cold-atom devices.
-
Product
Shortwave Power Amplifier
OM4001A
-
The OM Power model OM4001A is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
4-Ch Isolated Relay Output With IRIG-B Card
ECU-P1761
-
specialized interface module that combines four independent, electrically separated (isolated) relay contact outputs for switching external devices with a dedicated input/output port for receiving or transmitting IRIG-B serialized time codes.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
Isolation Relays
-
TransData Isolation Relays provide surge protection for energy metering installations by electrically isolating the pulse input/output wiring path to protect electricity meters, network components, energy management systems and recording devices from damage caused by transmitted or induced electrical surges.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
Thermocouple Interface Amplifiers
-
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
Product
ULI-234TE - Heavy Industrial RS-422/485 (Terminal Block) Isolated Repeater
BB-485OPDRI-PH
-
RS-422/485 Repeator2kV, 3-way isolation (input/output/power)Data rates:1.2 to 115.2 KbpsWide operating temperature range: -40 to +85 °CIEC-61850-3, IEEE-1613, NEMA TS2, FCC, CE10 to 48 VDC input power (power supply required, sold separately)
-
Product
PXI-8432, 2-Port, Isolated, RS232 PXI Serial Interface Module
779743-01
-
2-Port, Isolated, RS232 PXI Serial Interface Module - The PXI‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
HF Amplifier
-
bsw TestSystems & Consulting AG
Whether a HF amplifier which is mounted in a 19" rack is viewed as an instrument, a system or a component largely depends on the point of view of the application developer. We list this product family here; however we would like to point out that our 19" amplifiers for rack-mount and benchtop applications, as well as modules without power supply, are listed in the "Components" section.
-
Product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
Product
19-inch Rack Mount(2U) 20 Watts 80MHz to 1GHz Power Amplifier
-
Chengdu KeyLink Microwave Technology Co., Ltd.
20 Watts 80MHz to 1GHz amplifier in a compact 2U package for oversea market. It is a rack mountable-unit incorporating a universal voltage power supply and a built in forced air-cooling system. This amplifier subsystem utilizes LDMOS power device that provides excellent power density, high linearity, low distortion and wide dynamic range. The KB00810S43A SSPA is ideal for EMC testing to various industry standard as well as Broadband Communication.
-
Product
Operational Amplifier
Op Amp Series
-
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Product
Panel-mounted Power Amplifier
PAC2000B
-
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
-
Product
SOA & Raman Amplifier
-
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
Product
Unipolar Variable Gain High Speed Amplifier
F70PV
-
The F70PV is a very fast, unipolar, linear amplifier having a variable amplification of 0-10 times and capable of voltage output of +70V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Product
Power Amplifier, RF
-
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
