Filter Results By:
Products
Applications
Manufacturers
Voltage Indicators
1) Digital Voltage Indicator. 2) Digital Visual Interface, is a standard for a uniform connector that can handle both digital and video signals.
See Also: Indicators, Angle Position Indicators, Fault Indicators, Loop Indicators
- Pickering Interfaces Inc.
product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 2-Pole
42-321-123-HI
The 40-321-123-HI (PXI) and 42-321-123-HI (PXIe) are hex 7-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
LED Synchroscope
LS-96 SYNC
Standard Electric Works Co., Ltd
● Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.● Square shape panel 96 x 96mm● 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS"● 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks● 360° indication● 12 o'clock position LED is bi-colored● PC window, ABS resin frame, PC case
-
product
Proving Units for High Voltage Testing Equipment
A high quality range of proving units provide the important role of verifying the safe operation of high voltage potential indicators used by power engineers, maintenance personnel and service engineers. The proving units are essential tools for testing HV equipment before and after use.
-
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Impulse Voltage Generator
Shanghai Sanki Electronic Industries Co., Ltd.
Impulse voltage generator Impulse voltage generator is mainly used for test products such as power equipment to perform lightning impulse voltage full wave, lightning impulse voltage chopping, operating impulse voltage wave and steep wave impulse voltage test, to inspect insulation performance. The technical indicators comply with national standards and IEC standards.
-
-
product
Car Battery Voltmeter
TE6-0607
Hangzhou Tonny Electric & Tools Co., Ltd.
Test the voltage on your car battery so you don't get stranded in the middle of nowhere! This Automotive Battery Tester measures the voltage of 12V or 24V automotive batteries by simply plugging into the cigarette lighter socket of your automobile. A 1.1-inch LCD displays the voltage and LED indicators display the power level.
-
product
Ultra High Voltage DC Power Supply
Output control can be switched between remote control and local control. The output display and output indicators are located directly on the front panel and can be directed to an external remote display. The high voltage output terminal has overcurrent, overvoltage, short circuit protection and arc protection.
-
product
Milliohm Meter
4136 mO
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Microprocessor-controlled.● Four terminal measurement.● Measures down to 100μΩ.● 5 Ranges from 200.0mΩ to 2000Ω.● Maximum resolution of 100μΩ.● Three test currents with over-temperature protection.● Protection against inadvertent connection to over voltage.● Large LCD.● Potential lead resistance and current lead resistance checks.● "Full-featured” EnerSave inside.● EnerSave Auto hold.● EnerSave Auto off.● Lightweight, robust & compact.● Indicators show if reading may be invalid (RP, RC, and temperature).● "O-Ring” sealed case.
-
product
Proving Unit
PU260
Proving unit to enable compliance safety checking of voltage indicators for safe operation prior to testing on a live circuit.It is a requirement by Electrical Safety Council and the HSE that every electrician proves their voltage testers before confirming safe isolation.
-
product
Dual Nav/Comm Test Panel
TA-155
The Best Dual Nav/Comm Test Panel on the market today. This panel is designed to test the KX155/155A and KX165/165A radios specifically as well as others and will allow by the book testing of these units. The panel includes specific switching for testing the intercom features, providing unit configuration and audio isolation as required. This panel also incudes basic provisions to run a second Nav/Comm using the long time standard 8 pin octal connector. Monitoring of either current or voltage to either radio is also provided. Integrated or stand alone testing of your OBS or converter indicators is provided as well as the required test jacks. Click on picture for larger view.
-
product
Load Length Meter
Design for finding out the total voltage of neon tubes in a circuit, help to Choose correct rating of neon transformer;- Easy to use just like a neon transformer;- With color LED indicators, clearly shows the test result;- With build-in over voltage protection circuit.
-
product
Test Voltage Indicators
PRV240FS
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
product
Voltage Indicators
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
product
Partial discharge measurement with remote wireless reading
PD-LT
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
product
Electrical Tester
T+
The T+ Electrical tester offer three ways to know if AC/DC voltage is present. It lights up, makes a sound, and vibrates for added user protection. With these indicators, the user will be alerted to the presence of voltage even in dark, or noisy environments. The audible indicator can also be easily switched off - with the push of a button.
-
product
Network & Cable Testers
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
product
Low Resistance Ohm Meter
6237 DLRO
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measure down to 1μΩ.● 6 ranges from 2.000mΩ to 200.0Ω.● Maximum resolution of 1μΩ.● Three test currents with over-temperature protection.● Four terminal measurement.● Protection against inadvertent connection to over- voltage. (crow bars for current and voltage)● Clear & large LCD.● Potential lead resistance and current lead resistance checks.● "Full-featured” EnerSave™ Inside.● EnerSave™ Auto-hold.● EnerSave™ Auto-off.● Rechargeable battery operated● Robust & compact.● Indicators show if reading may be invalid (RP, RC, and temperature).● "O-Ring” sealed case.
-
product
Fault Passage Indicator for Overhead Lines
Sensorform OFI-FLS
The Sensorform OFI-FLS is a Fault Passage Indicator for Overhead Lines, which is designed to assist in the rapidlocation and isolation of faults on Medium Voltage networks (1-38kV). When the current in the phase exceeds a preset level, the fault is indicated by means of both a mechanical flag indicator and high-intensity LED indicators.
-
product
POWER PROBE III WITH CLAM SHELL - GREEN
PP3CSGRN
*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground
-
product
Hipot
AC, DC, AC and DC
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators with easy to read legend.• Continuously variable output from zero to full voltage.• Low end ground test.• Multi range analogue kV meter and current meter.• Fast acting overload circuit breaker.• Zero start interlock.
-
product
Non-Contact H.V. Detector
300 HP
Standard Electric Works Co., Ltd
● Protection class : IP66.● 3 LED indicators in a circle for easier viewing in any directions (360° LED indication).● 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV.● High bright LED visual indication.● With the longer shelter to make the 3 LED indicators brighter under the sun.● Sound indication.● The maximum voltage setting can be 500kV .● Self-test function.● Power source : 1.5V "C" type battery × 3.● High impact nylon casing.● Non-contact work by proximity.● Compatible with most hot sticks.● Lightweight, robust & compact. ● Suitable for indoor and outdoor use.● Easy access to batteries.● Special ranges are available upon request. ● The maximum detection range can be 500kV.● Meets EN 61326-1 CISPR 11 EN 61000-4-2 EN 61000-4-3 EN 61000-4-8
-
product
Plug-In Power Supplies
VECTOR Electronics and Technology, Inc.
Standard PCI output Voltages : 5.0V, 3.3V, +12.0V, -12.0VHot swap, N+1 redundancy with internal OR-ing diodes.99 power factor corrected AC 90-264V input DC 36-72V (48V nom.), or DC 18-32V (24V nom.) Current sharing on 5.0V and 3.3V outputs Power & Fault LED indicators to faceplate Excellent performance
-
product
Test Board For QSFP+ Transceiver
EQSFP10
The OPTELLENT EQSFP10 is a cost-effective and convenient test board for testing QSFP/QSFP+ optical transceivers in R&D and manufacturing environments. The EQSFP10 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP10 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Multi-Volt Twin-Lead Tester
69135
Checks and indicates voltage on circuits up to 460 volts, AC or DC.Tests for DC polarity, frequency, and polyphase line.Four separate bright neon AC/DC indicators indicate voltage being tested 110, 220, 277 or 460 volts.Reinforced test leads, stored in the case, and furnished with probes on the ends.Reinforced casing.
-
product
6-400V DC / 120-400V AC Universal Voltage Tester
1989A
Peaceful Thriving Enterprise Co Ltd
This is a convenient, low-line voltage tester which features 4 LEDs and 3 neon lamp indicators 6-400VDC or 120-400VAC.
-
product
Carrier Demodulator with LED Display
CD23/223
The CD23 and CD223 Digital Transducer Indicators are designed for use with variable reluctance and differential transformer transducers. The CD23 accepts input from a single transducer, and the CD223 accepts two switch-selectable inputs, with Zero and Span controls for each input. The indicators provide 5 Vrms, 5 kHz carrier excitation voltage to the transducer(s) and solid state circuitry to amplify, demodulate and filter the transducer output signals. A 3 1/2 digit front panel display is standard, with a 4 1/2 digit display optionally available.
-
product
Seaward HV Test Equipment
Experts in High-Voltage Test Equipment Seaward has been designing and manufacturing high-voltage test equipment for over 37 years and continues to innovate and bring the best instruments to the market. Choose from phasing sticks, safe discharge rods, voltage indicators and more.
-
product
DC Electronic Load
M9822/M9822B
M9822/M9822B is newly designed circuit adopts rapid AD and DA technology to achieve rapid measurements with high accuracy. And the resolution of 0.1mV/0.1mA can effectively display the minor change of voltage and current, so the instrument has a wider application field and achieves better test results. Meanwhile your operation becomes much more comfortable and easy by equipping the high-light VFD, the simple menu and displayed contents and the operation state indicators on all keys. Otherwise the complete and humanized test functions will greatly improve your productivity.
-
product
Voltage Indicators
Available with a digital readout or a simplified LED display Seaward's specialist range of voltage testers have the versatility and durability to cope with all types of user demands.
-
product
Auto Charging System Analyzer
TE6-0606
Hangzhou Tonny Electric & Tools Co., Ltd.
This unit simply plugs into your car's cigarette lighter socket and will present you with alternator and battery status. On the left side is the alternator status indicating if it's charging the battery at too high a voltage, normal or too low. On the right is the battery status green LED charged 12.4-12.6V, yellow LED recharge 11.8-12.35V, and red LED dead<11.75V indicators.
