3U PXI Chassis
See Also: PXI Chassis, 6U PXI Chassis, Portable PXI Chassis
-
product
8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - 3U VPX
Model 52132
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2, &3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
product
PXIe-8881, 3.9 GHz 8-Core PXI Controller
786636-01
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
PXI 2A Multiplexer, 4-Bank, 16-Channel 2-Pole
40-614-007
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXIe-5667, PXI Vector Signal Analyzer
782366-01
Up to 7 GHz PXI Vector Signal Analyzer—The PXIe‑5667 is optimized for spectrum monitoring applications such as radio monitoring, interference detection, spectrum regulation, and related applications in line with ITU recommendations. It features real-time signal analysis and advanced signal processing using the capabilities of the built-in FPGA. The PXIe‑5667 includes options for various frequency ranges and instantaneous bandwidth.
-
product
PXI Dual 2x2 Insert/Bypass Switch ST
40-860-522-M
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI 3A Power MUX BRIC, 3-Channel, 48-Pole
40-571-003
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXI 25 x DPST Electromechanical Relays
40-146-002
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI Multiplexer, Dual 32-Channel, 1-Pole
40-630A-022-D/32/1
The 40-630A-022-D/32/1 is a dual 32-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
PXI High Density MUX BRIC, 6-Chan, 160-Pole
40-570-016
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI Simulation Modules For Sensor Simulation
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
product
PXI Breadboard Module, 2-Slot, 50-Pin D-Type
40-220A-502
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
PXI Relay Driver Module
The PXI Relay Driver Module controls up to 64 external relays with up to 50 VDC or 600 mA per channel drive capacity when using an external power supply. Modules can drive small DC motors or other inductive relay coils, and they include overcurrent, overvoltage, and flyback protection to ensure long operation. The PXI Relay Driver Module allows you to build custom switch configurations while using the standard IVIcompliant NISWITCH driver software.
-
product
PXI High Density Multiplexer, 10-Bank, 16-Channel, 1-Pole
40-615A-003
The 40-615A-003 is a 10-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful here a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
9-slot Chassis
CH-09 AXIe-0
The 9-slot chassis in AXIe-0 format is intended for use in modular measurement information systems based on the AXIe standard.
-
product
PXI 2A Multiplexer, 16-Bank, 8-Channel, 1-Pole
40-614B-001
This 16-bank, 8-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Type 12R1 Family of 19" Rackmount Chassis Platforms, Reduced Weight, Rugged
12R1
The Type 12R1 family is a 19" rackmount chassis platform that is rugged yet lighter weight than the sturdier Type 12R2 platform. The chemical conversion coating provides corrosion protection and electrical conductivity. The rear evacuation cooling system uses high CFM blowers to remove the heat generated by the board payloads.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-04
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
PXI 4x4 10GHz Matrix with Loop-Thru
40-787-518-4X4-L
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
product
PXI 3A Power MUX BRIC, 40-Channel, 6-Pole
40-571-405
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781262-01
PXI Vector Signal Generators offer custom and standard modulation, as well as the ability to generate communications standards formats such as GPS, WCDMA, DVB-H, and more. They support quadrature digital upconversion, which reduces waveform download and signal generation time, as well as stream-to-disk capabilities. The power and flexibility of PXI Vector Signal Generators make them ideal for use in scientific research, communications, consumer electronics, aerospace/defense, and semiconductor test applications as well as for areas such as software-defined radio, radio-frequency identification (RFID), and wireless sensor networks.
-
product
PXI 3A Power MUX BRIC, 48-Channel, 6-Pole
40-571-406
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXI 48 x SPDT Power Relay Module
45-157-001
The 45-157 SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC.
-
product
PXI High Density MUX BRIC, 64-Chan, 10-Pole
40-570-414
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI Multiplexer, 18-Bank, 3-Channel, 1-Pole
40-617A-021
The 40-617 18-Bank, 3-Channel, 1-Pole Multiplexer Module is part of our range of reed-relay based switching solutions. The Module consists of 18 electrically isolated banks of multiplexers controlled by a PXI/PCI interface. Each bank is a 1 to 3 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously.
-
product
PXI 2 Amp MUX, Single 16-Channel 2-Pole
40-635-102
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI MUX 1-Bank of 80 Channel 1-Pole
40-615-021-1/80/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
60-Watt DC/DC Converter, 3U cPCI
55KQ2-02
NAI’s 55KQ2-02 is a 60 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 60 Watts. It is designed to work along with NAI’s 72.5 DC Power Line Conditioner w/Holdup companion unit, model 44KS3-02.
-
product
3U VPX SDR Module
VPX3-ZU1-SDR
Sundance Multiprocessor Technology Ltd.
The VPX-ZU1-SDR from PanaTeQ is a 3U OpenVPX module based on a Xilinx Zynq Ultrascale+ MPSoC ZU6EG/ZU9EG/ZU15EG using JESD204B interface to an Analog Devices AD9371 or AD9375 Wideband RF Transceiver. Available in Air Cooled or Conduction Cooled version (see picture), this module offers incredible capabilities for the developers looking for ruggedized Software Defined Radio applications and targeting the defence/aerospace market. The module can work as stand-alone module or can be the SBC of the VPX system using the power effecient Quad-Core ARM Cortex A53 SoC and the on-board PCIe Gen2 Switch (worldwide unique feature)
-
product
PXI 3A Power MUX BRIC, 12-Channel, 12-Pole
40-571-303
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
