-
Product
10 MHz to 6 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2061XA
Power Sensor
The Keysight L2061XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz LAN peak power sensor.
-
Product
Three Phase Reference Standard Meter
-
Signals & Systems India Private Limited
The Three Phase Reference Standard Meter (TPRS-1107) is portable equipment from SANDS. The main objective of this device is to calibrate the errors in three-phase and single-phase energy meters i.e. the meter under test (MUT). The TPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, power factor etc of the meter under test. It has an LCD display, an alphanumeric keypad that makes it easy for the user to operate the TPRS. It can be interfaced with the PC for data analysis. It has the capability of storing up to 8000 test results.
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
1550nm High Power Fiber Optical Splitter
HPFS-1550-口口-1×N
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HPFS-1550 series high power fiber optical splitter and adopt special process of fused bi-conical taper technology and good heat treatment. It can be applied by divided high performance and high reliability to multi-port optical power distribution of 1550nm high power laser light source. The maximum pass power is 50W（47dBm）.The feature of the product is high stability, high uniformity, low polarization dependent loss and low excess loss.
-
Product
Smoke Detection Sensor – 120VAC Wire-In with Battery Backup
ENVIROMUX-SDS-120V
-
For warning of smoke and invisible fire particles. Ionization smoke detector. Applications from 40°F to 100°F (4°C to 38°C). Front loading battery door. 9V battery backup (included) in case of power failure. One button design for easy testing and HUSH mode activation control. LED indicates four modes of operation: standby condition, alarm condition, alarm memory and hush mode. Hush mode: silences false alarms for 8 minutes, or low battery warning for 13 hours. Voltage supply: 120VAC. Pre-stripped wiring harness with tinned strands. Audio alarm: 85dB at 10ft. Dimensions: 5" diameter x 1.75" depth. Dust cover prevents false alarms. Tamper resist feature. Links with up to 24 devices. Max distance between first and last device: 1000ft (305m). Alarm memory indicates initiating alarm in interconnected systems. Use compatible relay (ENVIROMUX-RLY-SDS120V) for connection to the ENVIROMUX system or other auxiliary warning devices such as external sirens or stairwell lighting. ENVIROMUX-RLY-SDS120V includes normally open and normally closed contacts. Contact ratings: 10A at 120VAC, 5A at 30VDC. Regulatory approvals: UL.
-
Product
PXI 18xSPST High Voltage Power Relay Module
40-330-002
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
Spectroradiometer
-
Spectroradiometer is usually used with a integrating sphere to measure the photometric and colorimetric parameters of all kinds of lamps. Relative spectral power distribution P(λ), chromaticity coordinate (x,y), (u,v), correlated color temperature Tc, color rendering index Ra, dominant wavelength, peak wavelength, spectral bandwidth, color purity, color ratio, SDCM, luminous flux, etc.
-
Product
Gigabit Ethernet Tester Module for 1G and 10G Packet
GAO-ENET-104
-
GAOTek Gigabit Ethernet Tester Module for 1G and 10G Packet is designed for installation and maintenance of Metro/Carrier Ethernet and IP services. It supplies a compact test solution for This test module functions with an intelligent network modular test platform. The test platform combines powerful function, flexible, convenience, fast and high-efficient advantages.
-
Product
Syscal R1 Plus Switch
-
The SYSCAL R1 Plus resistivity meter is specifically designed for medium-depth exploration. It combines a power source, transmitter up to a 200W or 1200Vpp output voltage, and a 2 channels receiver in a single unit; its compactness makes it an effective tool for intensive resistivity surveys.
-
Product
8-Pin Power D-Type Cable, Female to Unterminated, Ferrules
A008PF4-F-5A050
Cable Assembly
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Multi Output Regulated DC Power Supply
LQ6324T
-
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
Product
Modbus Master TCP/IP Component for .NET
WSMBT
-
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
-
Product
Isolated USB To RS-232/422/485 Converter
ADAM-4561
-
Power from the USB portHot swap function supportedIsolation protection 3000 VDC providedAutomatic RS-485 data flow controlTransmission speed up to 115.2 kbps
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Heat Exchangers RF Coaxial Loads
86500 Series
-
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
Product
Inversion Loss
DSP-1L
-
Is used to protect your three-phase motors against loss, imbalance or inversion. It continuously monitors each phase of your power supply. In case of phase loss, imbalance or inversion, the DSP-1L cuts off the power to the control circuit and thus protects the motor concerned.
-
Product
Circuit Tester "Light and Sound" Hook Probe
TE6-0708C
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Tests 6/12 volt circuits with POWER ON.*Interchangeable tips allow tool to be used as a probe- or pierce-type tester.*Retains wire for perfect pierce with one hand.*Hook grabs hard-to-reach wires.*Durable insulated clip and heavy-duty cord for professional use.*Spring loaded strain relief prevents cord pull out and damage.*High intensity glow for under hood and under dash visibility.*Easy-to-hear buzzer provides quick circuit test confirmation.
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
Gain-Compression Measurements
S95086B
-
The S95086B Gain-Compression Measurement (GCA) software provides fast and accurate input power, output power, gain, and phase at the compression point of an amplifier or frequency converter over a specified frequency and power range. With a simple setup, GCA reduces test times through an easy-to-use, fast, and accurate SMART Sweep. GCA also includes a guided calibration that corrects for absolute power levels, frequency response, and mismatch errors.
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector, With Interlock
42-153-104-HI
Relay
The 40/42-153-104-HI is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 37-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 52.4kΩ
40-251-033
Programmable Resistor Module
The 40-251-033 is a programmable resistor module with 4 channels which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Low Power Op Amplifiers (< 1mA/amp)
-
Analog Devices low power op amps offer a variety of benefits in many applications such as prolonging battery life, easing waste heat management in end equipment, reducing self heating to minimize thermally induced offset shift, and reducing total system power consumption and cost. Offering power efficient devices without compromising speed, noise, and precision has been a key focus on developing products at ADI.
-
Product
CPCI/PICMG 2.16 Intel Core 17th Gen. System
CP6004-RA_RC
-
The CP6004-RA/RC, a CompactPCI PICMG 2.16 compliant 6U CPU board, comes with various rugged levels, making it yet another addition to Kontron’s rugged PICMG 2.16 portfolio.Based on the Intel® Core™ i7 third generation processor and the QM77 platform controller hub, the CP6004-RA/RC is featured by dual or quad core computing performance at a reasonable thermal design power, including a complete set of data, communication and multimedia interfaces.
-
Product
Live-Dead-Live Meter Verifier
LDL-1200
-
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
Product
2U Family of Programmable AC-DC Switching Power Supplies to 1400W
-
The 2U family of programmable AC-DC power supplies sets a new standard for flexible and reliable power for your application. Available in a Rack Mounting or Benchtop at 1400W power levels with single output voltages ranging from 10 to 270V and current capabilities up to 120A. A user-friendly front panel provides reliable linear controls for finer adjustment and digital LED voltage and current meters. Standard features include; 'soft start' operation and 'no load' operation, thermostatically speed controlled fans to limit acoustic noise, short circuit and overload protection, thermal protection, internal EMI filtering, RFI shielding and remote sensing.
-
Product
Cable Tracing
-
High-power tone generator enables signal detection over 20 miles away and makes tracing through walls and enclosures easier with multiple tones and power levels suited for network, signal wire, coax, and telephone cable applications.
-
Product
Earth Leakage Breaker And Residual Current Device
IGR Series
-
IGR Leakage Current Analyzer is invented as the world first, and also can measure Insulation Resistance (MO) without power cut-off. This patented instrument can analyze leakage current, and display Igr(resistive), Igc(capacitive), and Io(vector sum), Ground Insulation Resistance, and the phase angle between voltage and current. (IGR ELB) - Operates due to Igr. - Properly-operating in spite of IGC in digital era. ( Not tripping on UPS load and Harmonics and noise area) - Possible to go down Igr for safety of people and animals. - Possible to manufacture high sensitive ELB. - Possible to prevent fire from electric leakage current.
-
Product
Optical Fiber Network Products
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
