RF Detectors
Sense the presence of radio frequencies.
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
Peak/Average Reading Directional RF Wattmeter
83000-A
-
When you need Peak power measuring capability in the 2 to 2300 MHz frequency range and from 100 mW to 10 kW, then you need to get your hands on our Model 83000-A RF Peak Reading Wattmeter -- only from Coaxial Dynamics.
-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, MCX
40-830A-103
Relay
The 40-830A-103 (PXI) and 42-830A-103 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-830A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
Microwave Wideband Direct Modulated DFB Transmitters (without RF Amp)
MT50 (40KHz~20GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT50 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
Product
Ultrasonic Optical Flaw Detector
MIV-X
-
Thanks to Shimadzu’s proprietary light imagining technique, which combines an ultrasonic oscillator with a stroboscope, defects near the surface of a material, including peeling of the bonding and adhesive surfaces of heterogeneous materials, as well as paint, thermal sprays, and coatings can be inspected easily and non-destructively.
-
Product
RF Device Test Socket
Coaxial Socket
-
With unparalleled technology, coaxial structure and high-precision machining equipment, LEENO can provide RF test socket with high bandwidth, impedance matching and high frequency up to 100Ghz.
-
Product
Gamma Detectors
-
In Gamma detectors, the gamma radiations produce electrons by interacting with the cathode material and the filling gas.These electrons ionize the gas and the charge carriers are collected by the electrodes. The resulting anode pulse is detected by a load circuit. The primary electrons are created by several interaction mechanisms:- Photoelectric effect- Compton scattering- Pair production
-
Product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector
40-728-002
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Process Sense™ NDIR End Point Detector For Chamber Clean
-
The Process Sense endpoint sensor is a small, low-cost SiF4 sensor specifically designed for Remote Plasma Chamber Clean Endpoint detection for silicon-based CVD deposition chambers. Process Sense is based on infrared absorption, the only technique applicable to all plasma cleaning processes (in-situ and remote). It gets mounted onto a bypass on the rough line, ensuring no effect on deposition hardware. The signal level reported by the Process Sense, which is proportional to SiF4 concentration, can be used to determine the completion of the chamber clean process.
-
Product
RF & Microwave
-
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
-
Product
Air Tightness Detector
FQ
-
Fuzhou Fuguang Electronics Co., Ltd.
FQ series air tightness tester is the latest high-precision non-destructive testing equipment developed by Fuguang Electronics. The equipment mainly uses compressed air as the medium to apply a certain pressure to the inner cavity or surface of the product to be tested, and then uses a high-sensitivity sensor to detect changes in pressure to determine the tightness of the product to be tested.
-
Product
RF COMPONENTS
-
If space is an issue and you are looking for high quality RF Components, ETL's wide range is designed and manufactured at the ETL factory. Covering DC to 40GHz, these are at the heart of many of our 19" Rack Systems.A key feature of many of ETL components is the ability to pass or block a 10 MHz signal or DC voltage through the products, which can be used to power interconnecting components or pass a stable frequency reference to a LNB or BUC within the system.
-
Product
Ultrasound Detector
D200
-
A heterodyne detector with backlit, large digit, accurate digital display, showing the tuned frequency in the heterodyne mode. The frequency and volume controls are on the side of the case, making it easy to adjust.
-
Product
RF Switch Matrix
-
Switch Matrices are offered in Blocking, Non-Blocking, and Super Non-Blocking configurations in mechanical housing packages of 1U-10U. Completely customizable control (USB, 10/100 Base-T) and expandable in blocks of 8 by 8 and 64 by 64 in a single unit, multiple units up to 256 by 256.
-
Product
Average Reading Directional RF Wattmeter
81000-A
-
The Model 81000-A Wattmeter ... now you can measure RF Power in 50-Ohm coaxial cable and transmission lines, and accept plug-in elements in the range of 100 mW to 10 kW full scale, and from 0.45 to 2300 MHz.
-
Product
Accessories for Gas Detectors
-
Electronic siren / Precalibrated sensor for gas leak detector ect.
-
Product
Mass Burette Flow Detector
FX-1100 Series
-
The FX-1100 Series Mass Burette Flow Detector takes the position of the fluid surface inside the burette as the head pressure using the differential pressure detector attached at the bottom and directly measures the flow of fluid as a mass based on changes in this pressure. It does not require calculation correction of temperature and specific gravity, and has many advantages such as high accuracy and extremely less affected by air bubbles, which enable to measure fuel consumption in the tests such as chassis dynamometer and engine bench. The 3 models are available according to the measurement range and application.
-
Product
Particle Counters And Detectors
-
Our family of particle counters and particle detectors contain instruments optimized for a variety of applications. In environmental research and monitoring, customers face high concentrations in city centers, near freeways or harbors, or very low concentrations in remote locations which are used as reference sampling points.
-
Product
Ground Fault Detectors
-
STB Electrical Test Equipment, Inc
STB's convenient Ground Fault Detectors may be operated with one hand and are ideal for preventative maintenance. Ground Fault Detectors indicate ground faults and electrical leakage while equipment is in operation.
-
Product
RF Solutions
-
ST offers wideband and multiband RF solutions for wireless communication infrastructure and RF equipment including GSM/3G/LTE base stations, microwave links, cable modems, satellite, broadcasting, instrumentation, security, defense and test equipment.
-
Product
TAP Detectors And Power Monitors
-
The “Premium” jumpers are VZ TPR Certified Cables that provide the highest level of reliability. We also offer the high performance “Standard” jumpers that are Telcordia GR 326 tested and certified. Both the Premium and Standard cables are made in our state of the art manufacturing facility recognized by leading global service providers as one of the best in the industry. We attribute our success to the highly dedicated and skilled production team which starts by selecting only the highest quality fiber and connector components.
-
Product
TERAHERTZ HOT ELECTRON BOLOMETER DETECTORS FROM 0.1 to 70 THz
-
Insight Product Company offers ultrafast superconducting hot-electron bolometers (HEBs) operating at terahertz frequency range. from 0.1 to 70 THz. Superconducting hot electron bolometers HEBs are designed to detect and register the electromagnetic radiation pulses in the frequency range from 0.1 THz to 70 THz.
-
Product
RF Amplifiers up to 500 MHz
-
Narrow and Broad band RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAsFET in Class A and Class A/B topologies for AM, FM, VHF, and UHF bands with output power ranging from 0dbm to 60dbm.
-
Product
FieldFox Handheld RF Analyzer, 4 GHz and 6 GHz
N9912A
-
CAT and VNA: 2 MHz to 4/6 GHzSA: 100 kHz to 4/6 GHz Carry the world's most integrated handheld RF analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional T/R VNA, spectrum analyzer, built-in power meter, and more Save time by measuring RL and DTF simultaneously in the same sweep Calibrate simply in the field with Quick Cal Easily measure average and pulse power with a USB power sensor
-
Product
PXI/PXIe MEMS RF Multiplexer, Dual 4-Channel, 4GHz, 50Ω, SMB
42-878-221
Multiplexer Module
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
PXI 8x4 RF Matrix 300MHz 50 SMB With Loop-Thru
40-729-001-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
RF Bridge, 50 Ohm, 300 kHz to 3 GHz
86205B
-
The Keysight 86205B high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
