RS-485
Serial communication line supporting 32 devices.
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
Isolated RS-485
-
Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications. The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus.
-
Product
RS-422/RS-485 Repeater
ND-6510
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
2Counter/2DO Modbus RS-485 Remote I/O
ADAM-4080
-
2ch counter/2ch digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VRMS isolation protectionCounter frequency up to 50kHZ
-
Product
8Thermocouple Modbus RS-485 Remote I/O
ADAM-4018+
-
8ch thermocouple(can be set to current)Protocols:Modbus RTU,ASCIIWatchdog timer to recover the system3000VDC isolation protectionWiring burned-out detection function
-
Product
RS-232/RS-485 Converter
ECD485
-
Deploy sub-metering sites and simple metering networks with ease using the EDMI MiniHub RS-232 to RS-485 converter.1/4 Load RS-485 modules allow for up to 128 devices over 1.2km of wired daisy-chain network, with each meter capable of becoming the Network Master and remotely connecting to a backhaul system via an integrated EDMI Modem Port redirect connector.
-
Product
Isolated RS-485
-
Renesas' isolated RS-485 differential bus transceivers provide bidirectional data communication for Industrial Internet of Things (IIoT) networks.
-
Product
8Relay Robust Modbus RS-485 Remote I/O
ADAM-4168
Relay Output Module
8ch relayOperation temperature:-40~85°C,Power input:10VDC~48VDCNoise protection: 4kV surge(power),4kV EFT,8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
8DI/8DO RS-485 Remote I/O
ADAM-4050
-
8ch digital input/8ch digital outputProtocols: Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
USB To 2-Ch High Speed RS-422/RS-485 Port Module
EMIO-220S
Expansion Module
USB to 2-Ch High Speed RS-422/RS-485 port module, Full size Mini PCIe & Module type combo. MiniPCIe thru USB & USB Pin Header, FIFO buffer 4K byte transfer, 4K byte receiver. Widely temperature from -40 ~ 85 degree.
-
Product
8AI RS-485 Remote I/O
ADAM-4017
-
8ch analog input(voltage or current)Protocols:ASCIIWatchdog timer to recover the system
-
Product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
-
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
Product
7DI/8DO Robust Modbus RS-485 Remote I/O
ADAM-4150
-
7ch digital input(counter)/8ch digital output (pulse output)Operation temperature: -40~85°C, Power input: 10VDC~48VDCNoise protection: 4kV surge (power), 4kV EFT, 8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
RS-422 RS-423 RS-485
-
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
Product
8AI Modbus RS-485 Remote I/O
ADAM-4017+
-
8ch analog input(current or voltage)Protocols:Modbus RTU,ASCIIWatchdog timer to recover the system3000VDC isolation protection
-
Product
- RS-232 to RS-485 2 Wire with LCD Display
Model 366
-
FEATURES: DataSpy® Status Display; Implements Low Cost LAN; Supports 32 Users; Uses Single Twisted Pair; External DTE/DCE Switch; Programmable Contention; Selectable Termination. The Model 366 allows interfacing RS-232 based equipment with networks/equipment using RS-485.
-
Product
8Power Relay Modbus RS-485 Remote I/O
ADAM-4069
Relay Output Module
8ch power relayProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
16DI RS-485 Remote I/O
ADAM-4053
Remote Interface Unit
16ch digital inputProtocols: Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
Isolated RS-232 To RS-422/485 Converter
ADAM-4520
-
Automatic RS-485 data flow control3000 VDC isolation protectionSurge protection RS-485 data lineTransmission speed up to 115.2 KbpsLED indicator to monitor status
-
Product
- RS-232 to RS-422/RS-485 Concentrator - Wiring Hub
Model 290
-
FEATURES: Break RS-485 Limit, Expand to 496 Nodes 16 Port Capacity; Each Port Settable to RS-422 or 2 Wire RS-485; Provides Isolation Between Ports; All Ports Surge Protected; Increased System Reliability. The Model 290 RS-232 to RS-422/RS-485 Concentrator offers a unique group of features for those applications using RS-422 and/or RS-485 for communications between a multiplicity of devices.
-
Product
USB⇔RS-422/RS-485 Conversion
SI-35USB-2
-
SI-35USB-2 is an USB converter, which converts USB of PC into RS-422/RS-485.
-
Product
4Relay RS-485 Remote I/O
ADAM-4060
Relay Output Module
4ch relayProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
PCI-104 8-Port, 4-port, And 2-port Multi-Protocol RS-232, RS-422, RS-485 Serial Communication Boards
104i-COM-8SM Family
-
The 104i-COM-8SM (PCI-104) family of multi-port, multi-protocol (RS-232, RS-422, RS-485), serial communication boards deliver up to eight high-speed serial communication ports for use in a wide variety of applications. The boards were developed for use by system integrators and manufacturers in the design of industrial and commercial systems. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD) in RS-232 mode.
-
Product
8DI/8DO Modbus RS-485 Remote I/O
ADAM-4055
-
8ch digital input/8ch digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VDC isolation protection
-
Product
8Thermocouple Robust Modbus RS-485 Remote I/O
ADAM-4118
-
8ch thermocouple(can be set to voltage or current)Operation temperature:-40~85°C,Power input:10VDC~48VDCNoise protection: 4kV surge(power),4kV EFT,8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
LAN⇔RS-422/RS-485 Conversion
SI-65
-
SI-65 is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
Product
RS-485/RS-422
-
Renesas' half duplex and full duplex RS-485/RS-422 transceivers are available in a variety of speed grades to address any application needing reliable data transmission over twisted pair wiring.
-
Product
16DI Modbus RS-485 Remote I/O
ADAM-4051
Remote Interface Unit
16ch digital inputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VDC isolation protection
-
Product
SparkFun USB To RS-485 Converter
-
This is the newest revision of this board and this breakout board pairs an SP3485 RS-485 transceiver with an FT232RL USB UART IC to convert a USB stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps.
