Thermocouple Simulators
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
Boiler Thermocouple Monitoring System
BTM
-
The Boiler Thermocouple Monitoring System is used to acquire and archive data from thermocouples mounted on boiler tubes. Since this system interfaces directly with Allen Bradley Control Logix PLCs via EthernetIP communication, significant cost savings can be achieved by using it as remote IO.
-
Product
Cable Assy 78-Pin D-Type Female to 32 x Mini Thermocouple Plugs
A078DFR-32M002T5A100
Cable Assembly
This 78-pin D-type thermocouple cable assembly is terminated with 32 male mini thermocouple plugs. It is constructed from 7/0.15 (26AWG) silver plated copper wire and screwlocks are provided to secure the D-type to its associated products.
-
Product
MIMIC® Cable Modem Simulator
-
MIMIC Cable Modem Simulator, is the industry's first integrated simulation tool supporting DOCSIS, allows cable modem developers and cable companies to perform real world, integrated cable and internetworking device simulations. MIMIC allows suppliers of cable modems to design, develop and test their products in a virtual and scalable network environment, assuring customers that their cable modems will work properly when deployed across heterogeneous environments. Cable providers can use MIMIC to simulate the 1000s of households that use cable modems to assure the scalability of cable management software. In addition, providers can also use MIMIC for large-scale Operations Support System (OSS) testing deployments in place of large banks of cable modems, which would be cost prohibitive.
-
Product
Fiber Optic Network Simulators
SIM-2FON-25
-
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
Product
PXI Analog Output / Current Loop Simulators
-
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
High Output Simulators
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
MIL-STD-1553 Simulator & Analyzer Applications Software
F-SIM-1553
-
Avionics Interface Technologies
Software GUI Application for Operating AIT MIL-STD-1553 Interfaces - Bus Monitor Captures & Recordings - Simulate Bus Controller and Remote Terminals (up to 31) - Operate Multiple Bus Channels (and MIL-STD-1553 Modules) Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Engineering Unit Displays & Software Widgets - MIL-STD-1553 A/B Mode Code operations - Also Supports ARINC 429, ARINC 664, Ethernet, & Data Load operations
-
Product
SAE AS5643 Mil-FireWire PXI Express Test & Simulation Instrument
HSSUB-6120
-
Avionics Interface Technologies
Highest density capability available in an AS5643 3U PXI Express, single slot instrument - Four (4) FireWire nodes, each with three (3) ports - Apps provide high-level (AS5643) and low-level (1394) access, while accommodating end-user customization - S100, S200, S400, S800 transfer rates - Support all Nodes operating concurrently at 800 Mbps - Independent transformer coupling for each port - Eight (8) standard PXI backplane triggers - Industry standard Texas Instruments IEEE 1394b Chipset - ANSI C (typical), C++/C#/LabVIEW
-
Product
Virtual Platform Development and Simulation
DEV
-
The Imperas Developer products consist of tools, models and infrastructure components critical for the high quality, rapid development and verification of embedded software, utilizing virtual platforms. The Developer products provide the necessary capabilities to develop platforms, including software simulation capability to execute embedded code on the platforms.
-
Product
NIBP Simulator
SC-4 SimCube®
-
The SimCube SC-4 provides all the necessary parameters for testing the basic features of a patient monitor including 3 NIBP simulations, ECG, Heart Rate Sequence, Respiration, Digital Manometer, and Peak Detect Test modes with the option to upgrade to include the OxSim SpO2 simulator and complete accessory kit. Features one-button operation for quick testing of patient monitors.
-
Product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
PMC Module
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
Gauge Type T Thermocouple Wire
W-TW-36P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For VME (6U)
AVC429-x
-
Integrated modular solution by using the AMCX429-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) carrier card.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
K Thermocouple Immersion Probe
TP651_TP652
-
Immersion "K" Type thermocouple probe. °C max: 1200. Response time: 6 s.
-
Product
30:1 Spot IR Thermometer with Type K Thermocouple
FLIR TG56
-
The FLIR TG56 provides non-contact surface temperature readings so you can quickly and easily take measurements in places that are out of reach. Providing a distance-to-spot ratio of 30:1, the TG56 can measure smaller targets from a safer distance. The thermometer gives you control to view your current reading and last two temperature readings simultaneously, and the color screen makes it easy to navigate and select settings.
-
Product
LOCAL LOOP SIMULATOR FOR TR-114 INCLUDING BRIDGED TAP
458-LM-A1-30-TR114
-
The Model 458-LM-A1-30-TR114 Local Loop Simulator for TR-114 is the ideal solution for simulating test loops as defined in TR-114 and includes a Bridged Tap. In addition, it is also suitable for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing of straight loops out to 24,000
-
Product
NVH Simulation
-
With our NVH simulation tools, you experience your data in form of virtual test drives, thus speeding up the development processes. Auralize transfer path analyses based on test bench data or evaluate the NVH performance of a system even before components and assemblies can be physically combined.
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.
-
Product
Battery Simulators
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
NGI Battery Simulators
-
Product
GoldenGate RFIC Simulation Software
-
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
Product
PXI Single 16 Channel Switch Simulator
40-485-221
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Non-Hydraulic Steering Module Test Simulator
SMTS
-
The Steering Module Test Simulator (SMTS) from MB Dynamics is a non-hydraulic turnkey lab test system, offering accurate, reliable and repeatable in-laboratory simulations of driver, road & vehicle inputs acting on a steering system, and their associated effects on steering system performance and annoying noises. Supports troubleshooting, identification, diagnosis, and resolution of root causes of unwanted noise and other performance issues common to EPS, EPHS, EPAS, MDPS, and HPS steering systems.
-
Product
Thermocouple Thermometer Data Logger
HD2108.2
-
Thermocouple thermometer with logger. Input for K, J, T, R, N, S, B, E type probes with miniature connector. Maximum, minimum, average.
