Thermocouple Simulators
-
Product
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
510104261
Receiver Module
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
-
Product
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)
510180111
SIM Insert
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 310130113 Receiver, i2 MX, 22 Slot VTAC/SIM Insert, EMINot loaded. Thermocouple patchcords need to be purchased separately.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
Large Area Solar Simulators
-
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
Product
31-Channel Thermocouple Input Signal Conditioner
U2802A
Thermocouple Signal Conditioner
The Keysight U2802A 31-Channel Thermocouple Input module is a thermocouple input signal conditioner device that functions to convert low input voltage signal from a thermocouple into an output voltage range suitable for the data acquisition device. The U2802A thermocouple signal conditioner is to be used together with the U2355A and U2356A model data acquisition to enable thermocouple inputs.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Solar Cell Simulation
Setfos
-
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
Product
Thermocouple (J-Type) And Temperature Probe Adapter
U1185A
Temperature Probe Adapter
The U1185A consists of a thermocouple bead (J-type) and a mini connector to dual banana plugs.
-
Product
UV Solar Simulators
-
UV Solar Simulators - please contact the company directly for more information.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Distributed Simulation & Test Environment
-
Modular hardware and software architecture with multipurpose modules and components in a common and reconfigurable simulation and test environment easily adaptable to meet project‐ and customer‐specific requirements.
-
Product
Vehicle Network Simulator
OBD Simulator™
-
Simulate Vehicle Network Messaging for OBD CAN, J1939 CAN, J1850 VPW, J1850 PWM, ISO-9141 and KW2000.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 12 Channel
43-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PCI Simulation Modules For Sensor Simulation
-
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
Product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Basic Rate and Primary Rate ISDN Network Simulator
Emutel Duo
-
Emutel Duo is a convenient and flexbile basic rate and primary rate ISDN network simulator. With 3 software selectable S/U interfaces and optional 2 E1/T1 interfaces you can test and develop a full range of ISDN equipment.
-
Product
K Thermocouple Immersion Probe
TP742
-
Immersion “K” Type thermocouple probe. Tolerance according to IEC 60584-2 standard.
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
6-Ch Thermocouple Input EtherCAT Slice IO Module
AMAX-5018
EtherCAT Slice IO Module
Channels: 6 differentialInput Type: V, mV, ThermocoupleInput Impedance: >2MΩVoltage Range: ±50 mV, ±100 mV, ±500 mV, ±1 V, ±2.5 VResolution: 16-bitFSR accuracy: 16-bit with ±0.1% @25°CSample Rage: 100 Sample/Second (per channel)
-
Product
Electromagnetic Environment Simulators
A2PATS® Products
Simulator
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
Product
K Thermocouple Penetration Probe
TP659
-
“K” Type thermocouple penetration probe. Tolerance according to IEC 60584-2 standard.
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Cycle Drop Simulation Generator
-
Beijing KeHuan Century EMC Technology Co,.LTD
Cycle drop simulation generator
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Aircraft Simulator
ePlane PC
-
Pneumatic connections Ps, Pt and AoA (option)High accuracy, high resolutionSelectable pressure units: hPa; mb; in Hg; mmHg; ft; m; kts; km/h, ft/min; and Mach number and needle equipment visualisationSoftware executable under Windows 2000 and XPUSB cable for PC connection
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
Thermometer / Cardiac / Invasiv, non Invasiv Blood Pressure Simulator
TBH-400
-
Test device for functional testing of medical thermometers (DIN EN ISO 80601-2-56), cardiac output, invasive (IEC 60601-2-34) and non-invasive blood pressure devices (IEC 60601-2-30).
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
8-CH Thermocouple Input Module
ND-6018
Data Acquisition Module
- Channels: 6 Differential & 2 Single-ended- Input Type: Thermocouple, mV, V and mA- Thermocouple Type: J, K, T, E, R, S, B, N,C- Voltage Range: ± 15 mV, ± 50 mV, ± 100 mV, ± 500 mV, ± 1 V, ± 2.5 V- Current Range: ± 20 mA- Isolation Voltage: 2500 VRMS
