Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
510104261
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
-
product
PXI Millivolt Thermocouple Simulators
Series 41-760
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
product
LXI And LXI/USB Modular Chassis
Our LXI modular chassis are available in 7 and 18-slot and our LXI/USB modular chassis are available in 2, 4 and 6-slot and support over 1,000 of our PXI modules. The PXI modules supported range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of simulation modules such as programmable resistors, digital I/O, power supplies, thermocouple simulators, function generator, battery simulators and attenuators. This gives you enormous flexibility to define a switching or T&M system to exactly match your needs.
-
product
PXI Simulation Modules For Sensor Simulation
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
product
Industrial Calibrators
A temperature calibrator, often called a thermometer calibrator, is used to correct inaccuracies in installed thermometers and temperature sensors, because temperature measurement is a critical parameter in many industrial processes. Although simulators are sometimes called temperature calibrators or thermometer calibrators and may be used to provide thermometer calibration for the electronics in an installed system, a temperature source with a calibrated reference sensor is still required to provide a complete and meaningful calibration. Fluke Calibration industrial and field temperature calibrators include: Metrology Wells; Field Metrology Wells; field dry-well calibrators; handheld dry block calibrators; Micro-Baths; large target infrared calibrators; field IR calibrators; ice-point dry-well; and thermocouple furnaces.
-
product
PXI Thermocouple Simulators
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
product
Thermocouple, ITA, 36", 24 AWG Thermocouple Wire K Type, Single Ended (3 Amps)
7-409803000-036
Thermocouple, ITA, 24 AWG Thermocouple Wire K Type (3 Amps), Twisted Pair, Single Ended
-
product
Solar Simulators
TriSOL CPV
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
product
Temperature Simulators
A single select button scrolls quickly between the 3 factory set calibration points for efficiency. Two models to choose from: 271-018 (0°F, 32°F, 212°F) and 271-019 (32°F, 212°F, 500°F). Each unit includes a 3-point UKAS Accredited Calibration Certificate so you know that you''re using a precision instrument. Also included is a 3 foot type K test lead for connecting up your type K meters. You get precision at an economic price. Simple and fast!
-
product
Grid Simulators
A grid simulator can be used to simulate the characteristics of low-voltage mains. For this purpose, all voltages and frequencies of the supply networks occurring worldwide can be simulated. Critical states such as short-term voltage dips or voltage peaks (surge/burst) can also be generated.The integrated sequencer function enables the generation of different network parameters, e.g. distorted waveforms and intermediate oscillations. Therefore, grid simulators are well suited for testing conformity to standards and especially for determining the behaviour of electrical equipment in borderline situations. Many European and other international standards are pre-programmed for testing.
-
product
NIBP Simulators
The full-featured SC-5 SimCube® NIBP Simulator provides ECG, Resp, Arrhythmias, Pacer Simulation, IBP, and more for accurate biomedical testing. The SimCube simulates real-life oscillometric pulses by varying both the shape and size of the wave as cuff pressure changes.
-
product
Thermocouple Switchbox
SWT-2
The SWT-2 is a compact, economical switchbox that lets you use two probes in a thermometer which has a single input. SWT-2 was designed with our BAT-12 Thermometer in mind - it is small and easy to carry in the field with a portable BAT-12 - but it also fits any miniature Type T socket. A subminiature connector mates quickly and easily to most Type T thermometers.
-
product
Ring Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
product
Thermocouple Probes
Type T
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
product
Thermocouple Calibrators
Practical Instrument Electronics, Inc.
PIE has a thermocouple calibrator to fit your needs from the PIE 520B single type thermocouple simulator to the advanced troubleshooting capabilities of the PIE 422Plus. Have you had issues in the past where your thermocouple calibrator wouldn’t work with some of the instruments in your plant? Our thermocouple calibrators are guaranteed to be compatible with all process thermocouple inputs including all brands of smart temperature transmitters, PLC input cards, DCS systems and multichannel recorders.
-
product
Thermocouple Calibrator
TC-100
The Thermocouple Calibrator provides high accuracy and measurement of ten common thermocouples, as well as mV.
-
product
Target simulators
Simat simulator is an advanced hardware simulator capable to simulate in infrared range several targets on quasi uniform background. In detail Simat simulator is a modular image projector capable to simulate in infrared range variable intensity, variable angular size, variable spectrum, spatially and temporally dynamic airborne type targets on quasi uniform background. Basically the aim of Simat to enable simulation typical airborne targets like aircrafts or helicopters for infrared imaging sensors used for surveillance of these targets. Optionally Simat can be modernized to enable simulation in both IR and UV/visible ranges as the projectors are built using broadband reflective optical elements.
-
product
ESD Simulators
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
product
Transportation Simulators
V - Series
L.A.B. Transportation Simulators are used to determine the ability of packages and products to withstand shocks and vibration encountered during the following courseof typical handling and transportation.
-
product
Simulators
In-Phase Technologies simulators are designed to simulate our customer’s operating product, allowing them to perform testing and “what if” scenarios
-
product
Damped Oscillatory Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
product
Thermocouple Probes
sensor that measures temperature. It consists of two different types of metals, joined together at one end. When the junction of the two metals is heated or cooled, a voltage is created that can be correlated back to the temperature.
-
product
Axle Load Simulators
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
product
Thermocouple Contacts
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
Thermocouple Sensor
CR15B
15' cable with 4" stainless steel sensorType J thermocouple wire with plug connection
-
product
3-Axis Motion Simulators
When a device under test needs to be stimulated with simultaneous movements around three axes, then a product from the ACUTRONIC three-axis motion simulator range is the right choice. Independent motion simulation in three axes makes them very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
product
TriSOL Large Area Solar Simulators
OAI has designed and engineered for large area markets Class AAA, ABA, or ACA Solar simulators with the same performance , quality, and reliability as our other solar simulator models. These large area solar simulators are available in several models.
-
product
Lightning Surge Simulators
LSS Series
A simulator to reproduce “High energy induced lightning noise” which is induced by potential change on the ground, or done to power lines or telephone lines as result of lightning current.This immunity test is required by major standards including IEC61000-4-5 and JEC 210/212 and is widely used in many industries.
-
product
Configurable Thermocouple Transmitter
HD778TR1
Configurable 4...20 mA/20...4 mA 2 wire temperature transmitter for K, J, T, N thermocouples.
-
product
Solar simulators
Solar simulators enable the measurement of (dark and) light IV characteristics and of power and efficiency of photovoltaic An artificial light source is used to create illumination conditions that are similar to those in natural sunlight. International standards hosted by ASTM, IEC and JIS allow to classify the properties of a solar simulator with respect to spatial light uniformity, spectral content of the light and time variation of intensity.
