RF Power Sensors
See Also: RF Power, RF Sensors, RF Power Meters, Rf Power Amplifiers
-
product
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps)
7-241914000-036
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps).
-
-
product
RF Hybrids
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
product
PXIe-4112, 2-Channel, 60 V, 1 A PXI Programmable Power Supply
782857-01
The PXIe‑4112 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
product
Clamp Sensors
Kyoritsu Electrical Instruments Works, Ltd.
Can measure AC current up to 1000A Flexible and light weight by the air core coil used at the sensor part Designed to meet the international safety standard IEC 61010-1 CAT IV 300V, CAT III 600V
-
product
RF & Microwave Cables
Low Loss, Low VSWR for Integrated Systems: MegaPhase also manufactures high performance coaxial cables using GrooveTube® technology for high power and phase-defined systems, including electronic warfare, telecommunications equipment and many other RF platforms on the ground, sea, air and space.
-
product
Strain Sensors
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
product
Photoelectric Sensors
Our broad range of photoelectric sensors is aimed at all automation solutions where noncontact object detection can be utilized. The wide variety of different operating principles, models, sizes and specifications means that the best possible sensor can always be found for the relevant application and all conditions that occur in practice can be met.
-
product
AC Sensor
This sensor started it all! Our original handheld sensor detects 50-1000 volts AC and is designed for a CAT IV environment. Always ready for use, this sensor can prevent electrical shock and is non-reactive to static electricity.
-
product
RF Sources
Textron Systems’ commercial RF Sources (RFS 340, SSI) provide an unmatched combination of frequency coverage, power range, signal fidelity and switching speed in either a two-slot VXI, 1U LXI®, or VME Synthetic Stimulus Instruments (SSI) format.
-
product
Frequency Sensor
DARE?s frequency sensors and monitors are available in both AC powered and DC powered models in a wide variety of standard or custom enclosures. Used in aircraft, ground support equipment (GSE), ground power applications, and other military and industrial applications, DARE frequency sensors, monitors, and frequency sensing relays will protect equipment that is sensitive to fluctuations in power line frequency from damage due to over and / or under frequency conditions.
-
product
Optical Sensors
Optical (Infra-Red) Proximity Switches with advanced and reliable technology for every application offer a flexible solution for automation, where other Proximity Switches can not perform. Optical Proximity Switches have distinct advantage of higher sensing distance over Inductive and Capacitive types.
-
product
DC System Power Supply, 30V, 25A, 750W
N5745A
The single output, 750W N5745A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
-
product
Web Sensor
P8552
The devices are equipped with two connectors for connection of the temperature and humidity external probes and three binary inputs for two-states signals. The dry contact or two-state voltage signal can be connect to the binary input.
-
product
RF Microwave Switching
Keithley S46
S46 and S46T Microwave Switch Systems are designed to simplify the automated switching needed to test a wide range of RF and telecommunication products and devices. The S46 can control 32 relay contacts in a package as small as a 2U high (3.5 in) full-rack enclosure. Choose the System 46T if your application requires a terminated configuration. It builds on the design technology of the unterminated System 46. The System 46T accommodates up to eight terminated SPDT coaxial microwave relays and four terminated multi-pole coaxial microwave relays.
-
product
RF signal distribution
SpectralNet™
Kratos Defense & Security Solutions, Inc.
RT Logic’s SpectralNet eliminates the physical distance limitations in RF signal distribution, enabling the optimization of ground infrastructure to improve flexibility, reliability and reduce costs. SpectralNet is the first product to digitize and transport RF spectrum over IP networks in a way that preserves both frequency and timing characteristics, and then faithfully reconstructing the original RF signals to enable processing, recording or retransmission at another location. SpectralNet provides advanced networking tools to ensure reliable transport of digitized RF across lossy public and private IP networks. SpectralNet brings analog RF data to the IP network world, unleashing the power of virtualization and centralization of ground architectures for satellite and range ground systems, teleports, UAV and missile ranges, and ISR data processing.
-
product
Web Sensor
T3511
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
RF Connector
Electrical connector designed to work at radio frequencies in the multi-megahertz range. RF connectors are typically used with coaxial cables and are designed to maintain the shielding that the coaxial design offers.
-
product
Cavitation Sensors
Cavitation is often induced by an external acoustic field which typically has very high acoustic amplitudes but the acoustic emissions from these cavitation events are significantly smaller. The small acoustic emissions are characterised by well defined spectral peaks at integer harmonics and sub-harmonics relative to the fundamental bubble frequency.
-
product
RF Spectrum Analyzer
RF-EXPLORER / 3
Monacor International GmbH & Co.
RF Spectrum Analyzer, 15-2700MHz, in a compact aluminum housing with two antennas (SMA connection) for the different frequency ranges, among other things to avoid frequency collisions when setting up radio links in the frequency range mentioned above
-
product
Sensors
We design, develop and produce state-of-the-art SIGINT sensors that seek, exploit, identify, and locate sources of RF energy, underwater sound, light, heat and other complex phenomena. These sensors recognize threats, gather intelligence, and allow our customers to make informed, strategic response decisions.
-
product
DS Sensor
Z-Gard DS Sensor
The Z-Gard DS Sensor is designed to detect the presence of carbon monoxide and nitrogen dioxide gases in parking garages, vehicle storage areas or wherever else these two toxic gases could be found. These sensors employ electrochemical sensors which generate a representative output signal proportional to the calibrated operating range.
-
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
RF SCOE System
RF SCOE Systems require fast yet reconfigurable data processing as well as RF Modulation capabilities.For which FPGA Cards inside the PXI Frames are well suited.
-
product
Eddy-Current Sensors
Eddy-Current sensors are noncontact devices capable of high-resolution measurement of the position and/or change of position of any conductive target. Eddy-Current sensors are also called inductive sensors, but generally "eddy current" refers to precision displacement instruments (or nondestructive testing probes) and "inductive" refers to inexpensive proximity switches. High resolution and tolerance of dirty environments make eddy-current sensors indispensable in today's modern industrial operations.
-
product
Bench Power Supply, Adjustable, 4 Output, 0 V, 32 V, 0 A, 3 A
T3PS43203
Bench Power Supply, Adjustable, 4 Output, 0 V, 32 V, 0 A, 3 A.
-
product
Turbidity Sensors
Turbidity sensors measure the amount of light that is scattered by the suspended solids in water. As the amount of total suspended solids (TSS) in water increases, the water's turbidity level (and cloudiness or haziness) increases. Turbidity sensors are used in river and stream gaging, wastewater and effluent measurements, control instrumentation for settling ponds, sediment transport research, and laboratory measurements.
-
product
RF Shield Box
Qosmotec Software Solutions GmbH
Qosmotec RF Guard is a RF shield box that allows engineers to create an affordable automated end-to-end test environment with each UE shielded individually. It enables the user to perform wireless network tests without undesired RF interference by protecting mobile devices from outside network frequencies.
-
product
Vision Sensors
Providing you the best range of Vision Sensor with effective & timely delivery.
