PCB Piezotronics, Inc.

Product

Conformal Ballistic Pressure Sensor

Model: 117B67

-

PCB Piezotronics, Inc.

Model: 117B67 - PCB Piezotronics, Inc.

Conformal ballistics pressure sensor, 22 WMRF, 22 WRF, 22 WRF WITH 0.50" Centerline, 17 RF Mag, 17 HMRConformal ballistics pressure sensor for 17 HMR, 17 Magnum RF, 17 RF Magnum, 22 WMRF, 22 WRF, and 22 WRF with 0.50" centerline caliber cartridges.

Product

Sub-Miniature ICP® Pressure Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB's sub-miniature 105C dynamic pressure sensors are specifically designed to fit into tight spaces where mounting space is at a premium.

Product

Canister Load Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.

Product

Accelerometers

353B15

-

PCB Piezotronics, Inc.

353B15 - PCB Piezotronics, Inc.

Sensitivity: (10 %);10 mV/g 1.02 mV/(m/s) Measurement Range:500 g pk 4905 m/s pk Frequency Range:(5 %)1 to 10000 Hz1 to 10000 Hz Frequency Range:(10 %)0.7 to 18000 Hz 0.7 to 18000 Hz Frequency Range: (3 dB)0.35 to 30000 Hz0.35 to 30000 Hz Resonant Frequency:70 kHz,70 kHz Broadband Resolution (1)0.005 g rms0.05 m/s rmsNon-Linearity:1 %1 % Transverse Sensitivity:5 %5 %

Product

Cable Test Box

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.

Product

Precision Condenser Microphone

2575

-

PCB Piezotronics, Inc.

2575 - PCB Piezotronics, Inc.

Performance:Nominal Microphone Diameter1"1" Frequency Response: Characteristic (at 0 incidence) Random IncidenceRandom Incidence Open Circuit Sensitivity: 45 mV/Pa Resonant Frequency (90 Phase Shift)8000 Hz8000 Hz[1] Inherent Noise<10 dB(A) re 20 Pa<10 dBTemperature Range (Operating)TBD FTBD C Humidity Coefficient of Sensitivity (0 to 95%, non-condensing)0.001 dB/%RH

Product

ICP Blast Pressure Pencil Probe

Model: 137B21B

-

PCB Piezotronics, Inc.

Model: 137B21B - PCB Piezotronics, Inc.

Quartz, free-field, ICP blast pressure pencil probe, 1000 psi, 1 mV/psi, BNC connector

Product

Electronics For Signal Processing

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

PCB Piezotronics manufactures a wide variety of electronics to power ICP®, PE (Charge Mode), MEMS, strain gage and other types of sensors. All of these products provide conditioning of sensor signals for transmission to data acquisition systems.

Product

Low Noise Coaxial Cables For Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Low noise coaxial cables are used with single axis and triaxial charge mode sensors. This table provides relevant specifications for four cable types. Type 003 is the most commonly used, but three other types are also available.

Product

Pedal Force Load Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.

Product

ICP® Shock Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.

Product

Torque Transducers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.

Product

Accelerometers

356A02

-

PCB Piezotronics, Inc.

356A02 - PCB Piezotronics, Inc.

Sensitivity (10 %)10 mV/g1.02 mV/(m/s) Measurement Range:500 g pk4900 m/s pk Frequency Range: (5 %)1 to 5000 Hz1 to 5000 Hz Frequency Range: (10 %)0.5 to 6000 Hz0.5 to 6000 Hz Resonant Frequency:25 kHz 25 kHz Broadband Resolution (1)0.0005 grms 0.005 m/s rms Non-Linearity: (400 g, 3920 m/s)1 % 1 % Non-Linearity (500 g, 4900 m/s)2 % 2 % Transverse Sensitivity:5 % 5 %.

Product

Acoustics

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

When it comes to selecting a microphone for product tests—whether for sound power, sound quality, or noise source location—there's no need to compromise to sacrifice quality or performance for affordability.

Product

High Temperature Charge Mode Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).