Carbon Monoxide
a toxic gas devoid of odor, color and taste.
-
product
Mid-Range Gas Filter Correlation CO Analyzer
Model N300M
Teledyne Advanced Pollution Instrumentation
The Model N300M is a microprocessor-controlled analyzer used to determine the concentration of carbon monoxide (CO) in a sample gas. The analysis method is based on the Beer-Lambert law.The N300M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
product
Indoor Air Quality Meter CO, CO2, Temp, RH%
AQM4
UEi Test & Measurement Instruments
Four measurements in one instrument; carbon monoxide (CO), carbon dioxide (CO2), temperature and relative humidity. Use calculated 8 hour Time Weighted Average (TWA) and 15 minute short term exposure limits of CO2 for compliance testing and CO measurements for safety testing. Record, recall or download all readings to personal computer for later analysis or record keeping.
-
product
Oxygen/Nitrogen/Hydrogen Analyzer
EMGA-930
This is a simultaneous oxygen, nitrogen & hydrogen elemental analyzer with high accuracy and repeatability suiting to cutting-edge technology's R&D as well as quality control in the market of steel, new materials, catalyst and so on. This is a new generation model optimized to fit to user's requests.The oxygen is measured as carbon monoxide and carbon dioxide by two non-dispersive infrared detectors, the nitrogen by a thermal conductivity detector and the hydrogen with non dispersive Infra Red detector as H2O.
-
product
Dual Gas Sensor
Z-Gard® DS MPO
The Z-Gard DS MPO Gas Sensor connects directly to a building automation system for dual gas monitoring solutions. It detects the presence of carbon monoxide and nitrogen dioxide.
-
product
DS Sensor
Z-Gard DS Sensor
The Z-Gard DS Sensor is designed to detect the presence of carbon monoxide and nitrogen dioxide gases in parking garages, vehicle storage areas or wherever else these two toxic gases could be found. These sensors employ electrochemical sensors which generate a representative output signal proportional to the calibrated operating range.
-
product
Combustion Gas Analyzers
Zirconia
ABB combustion gas analyzers are designed for combustion optimization / control and emissions monitoring applications. The range includes in situ Oxygen only analyzers and an Oxygen plus combustibles (carbon monoxide equivalent COe) close-coupled extractive analyzer.
-
product
SparkFun Environmental Sensor
BME688 (Qwiic)
The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The gas sensor on the BME688 can detect a wide variety of volatile organic compounds (VOCs), volatile sulfur compounds (VSCs), and other gases such as carbon monoxide and hydrogen in the part per billion (ppb) range. Combine that with precise temperature, humidity, and barometric pressure and the BME688 can work as a completely standalone environmental sensor all in a 1in. x 1in. breakout!
-
product
Multiple Gas Transformer DGA
MINITRANS
Based on the same core technology as the highly successful TRANSFIX the MINITRANS is a lower cost alternative, monitoring three key gases: Hydrogen, Acetylene and Carbon Monoxide (in ppm) plus moisture in oil (%RH & ppm). The measurement of these gases allows the user to detect a wide range of developing faults including arcing.
-
product
Gas Detector
Shenzhen UYIGAO Electronic Technology Co., Ltd
Gas detector is a portable detector for detecting carbon monoxide (CO) gas.
-
product
Infrared Camera for CO Detection and Electrical Inspections
FLIR GF346
The FLIR GF346 optical gas imaging camera detects carbon monoxide (CO) and 17 additional gases without the need to interrupt your plant's production process. CO emissions can be a significant threat to primary steel manufacturing operations; even the slightest leak in a vent stack or pipe can have a devastating effect. With the FLIR GF346, inspectors can scan large areas from a safe distance, pinpointing leaks in real-time, reducing repair down-time, and providing repair verification.
-
product
Air, Soil, Liquid, And Gas
Omega's Environmental products include Water Quality Sensors, Transmitters and Controllers. Air Quality devices include indoor air quality Transmitters and Industrial Carbon Monoxide Transmitters.
-
product
Industrial Gas Detectors
Seitron designs and manufactures detectors for methane, LPG, gasoline vapours and carbon monoxide (CO) for commercial and process industry use. Our detectors provide three communication protocols 4..20mA, Modbus and S-Bus (a proprietary protocol derived from Modbus). You can also choose between two types of housings: polycarbonate for industrial use or ATEX-certified for the installation of detectors in ATEX-classified areas.
-
product
Mill & Silo Monitoring System
MSM-100
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
product
Telecom Gas Monitors
SMC 2350/2360
The SMC 2350/2360 Telecom Gas Monitors both continuously monitor for the presence of Carbon Monoxide (CO), but the Model 2360 also monitors for combustible gases.
-
product
Oxygen Meters
In the diverse PCE range you will find an oxygen meter for water and gases. We have available an oxygen meter for water for both pure oxygen content and for oxygen concentration. The oxygen meter for water and gases has a water resistant design, interface and internal data memory as well as the classical version for laboratories. The oxygen meter for gases follows the security norms and is used for detection and measurement of methane, hydrogen sulfide, carbon monoxide and oxygen (as well as 50 more gases).
-
product
Gas Detectors
At PCE Instruments you will find a professional quality gas detector / gas detection instrument for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
product
Air Quality Meters
An indoor air quality meter is used in confined spaces to prevent mold, to monitor CO2 levels, or to detect gas leaks. Whether portable or fixed, handheld or wall mounted, air quality monitoring equipment is essential for ensuring health and safety. At PCE Instruments, you will find air quality monitoring devices that meet various industry standards relating to personal safety and that are used to detect, measure and monitor relative humidity, ambient temperature and / or levels of carbon dioxide (CO2), volatile organic compounds (VOCs), formaldehyde (HCHO), freon and other refrigerants (CFC / HFC), phosphine (PH3), hydrogen sulphide (H2S), carbon monoxide (CO), nitrogen dioxide (NO2), oxygen (O2), ozone (O3) and other flammable, hazardous or toxic gases.
-
product
Gas Measuring Instruments
N Series
Teledyne Advanced Pollution Instrumentation
N Series Gas Measuring Units for SO2 (Sulfur Dioxide), NO, NO2, NOX (Nitrogen Oxide, Nitrogen Dioxide), CO (Carbon Monoxide), CO2 (Carbon Dioxide), O3 (Ozone), True, Direct NO2, NOX, NO, CH4 (Methane), THC (Total Hydrocarbons), and more
-
product
Combo Gas Monitor
Z-Gard Combo Gas Monitor
A cost-efficient monitor for underground garages and ventilation control, the Z-Gard Combo Gas Monitor uses an electrochemical sensor to detect carbon monoxide. The unit features local audio/visual alarm status indicators and it can be configured to interface with air-handling equipment to control air quality within a building.
-
product
Gas Meters
At PCE Instruments you will find a professional quality gas meters for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2 m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
product
IAQ Meters
General offers five indoor air quality (IAQ) instruments that measure and track four key IAQ parameters: Carbon monoxide, carbon dioxide and two toxic gasesformaldehyde and volatile organic compounds (VOCs). The last two substances have made news lately for their ubiquity, invisibility and toxicity.
-
product
Combined Probe for IAQ
P37AB147
Temperature, relative humidity, atmospheric pressure, CO2 (Carbon Dioxide) and CO (Carbon Monoxide) combined probe, complete with SICRAM module.
-
product
CO (Carbon Monoxide) Gas Sensor
605-00007
The CO Gas Sensor is used in gas detection equipment for detecting Carbon Monoxide in home, automotive or industrial settings. When paired with our Gas Sensor Board (#27983) it provides a development system and test platform for CO gas sensor design.
-
product
Mid-Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300M
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance from low to high range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
OLLI - gas detector / measuring device
Gas measurement & warning instrumentExplosion-proof & compact handheld gas measurement instrumentas diffusion device. It can be used for up to 5 combustible and toxicgases as well as oxygen and comes in an extremely rugged2C synthetic housing with a Li-Ion rechargeable battery.Explosion-proof measurement instrument formethane (CH4),propane (C3H8),oxygen (O2),carbon monoxide (CO),carbon dioxide (CO2),hydrogen sulfide (H2S)
-
product
Mid-Range Gas Filter Correlation CO Analyzer
Model T300M
Teledyne Advanced Pollution Instrumentation
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.
-
product
Environmental Testers
Axi'An Beicheng Electronics Co., LTD.
Environmental Testers by RuoShui: digital thermometers, thermal imaging analyzer, infrared thermal imager, thermo-hygrometer, nicety meters, rain gauge, coating thickness gauges, combustible gas detector and monitor, carbon monoxide monitor, digital anemometer, vibrometer meters, storboscope tachometers, digital tachometer, combustible gas detectors, 4 in 1 gas detector, digital refractometer, wood moisture meter, lux meter, sound level meter, sound meter, and more.
-
product
Gas Filter Correlation CO Analyzer
Model N300
Teledyne Advanced Pollution Instrumentation
The Model N300 is a microprocessor-controlled analyzer based on the Beer-Lambert law that is used to determine the concentration of carbon monoxide (CO) in a sample gas.The N300 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb Infrared (IR) light. The analyzer passes the IR light beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
product
Optical Gas Imaging Camera
EyeCGas CO
Opgal Optronic Industries Ltd.
EyeCGas CO is a handheld OGI camera for CO gas leak detection. With this camera you can safely and remotely detect and locate carbon monoxide as well as other harmful gases emissions. It is also the only OGI camera that is certified for ATEX zone 2 and UL class I Div II, hazardous environments. The EyeCGas CO allows for routine and on-demand inspections in the steel manufacturing operations and other industries where CO emissions need to be closely monitored. With EyeCGas CO, Opgal helps you detect and repair toxic gas leaks inside the facility, whether in vent stacks or pipes, allowing video and audio recording while maintaining safety. Whether these toxic gases are part of the manufacturing process, or a byproduct of the production line, EyeCGas CO helps increasing safety and protect the environment.
-
product
Portable Gas Detection
GT Series
Teledyne Gas & Flame Detection
The GT Series is a range of Portable Gas Detection instruments that combine quality, ruggedness and advanced technology in a user friendly, hand-held gas detector. It has been designed for the gas industry, satisfying all the needs of service technicians within a single unit.Applications: Leak test, confined space entry, barhole testing, carbon monoxide, purge, sniffer pressure leak tightness.
