Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
-
Product
Fixture Interface Module 2 Test Matrices
OTP2 module no.193
Interface Module
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
-
Product
Small Footprint Flex 20 ATE
Flex 20
-
The Flex 20 is floor mounted but maintains a small footprint on the shop floor. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
Product
Flying Probe Testers
-
SPEA’s Flying Probe Testers help manufacturers of printed circuit boards to deliver top-quality products in the fastest time-to-market, avoiding fixture cost and increasing accessibility when compared to bed-of-nails testers.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Custom PCB Test Fixtures
-
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
Product
(ITA), Breakout Box & Fixtures
ITA
WinSoft provides a wide range of Interface Test Adapters (ITA) and test fixtures to meet the most challenging functional test and signal conditioning requirements. This includes high frequencies, voltages and current.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
Hand Held Test Fixtures
-
Manual, or semi-automated mechanical devices designed to secure a Device Under Test (DUT) and provide a stable interface for electrical testing, inspection, or programming.
-
Product
S6 Slide Mount
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common test racks. Slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. Measure the rack depth between mounting rails and choose the slide kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
Single Screw Electromechanical Universal Testing Machine
CMT Series
-
Jinan Testing Equipment IE Corporation
The CMT series single screw testing machine is designed for mechanical property test mainly on metal materials, cement, asphalt, and bitumen etc. A variety of fixtures can be offered to do compression, bending and shearing test as well. This series of single screw testing machine is suitable for the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many fields such as industry factories, mineral enterprise and high schools.
-
Product
Receiver, G12x, 18 Module, with 20" Platform, for Slide Mount
310104385
Receiver
The 20” G12x Receiver provides rack mounting and tabletop mounting options. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Edge Press Technology Bed of Nails Testers
Rand Edge Press Family
-
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
Product
Keying Pin Kit, Receiver/ITA
310118112
Keying Pin Kit
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
Product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
-
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
Product
Femto / Picoammeter, 0.01fA, Battery
B2983B
-
The B2983B Femto/Picoammeter is the world’s only graphical picoammeter that allows you to confidently measure small currents with 0.01 fA (0.01 x 10-15 A) resolution. In addition, battery operation eliminates AC line noise from your critical measurements. It possesses a 4.3” color LCD with a graphical user interface that provides trend chart and histogram data in addition to numeric information. These front-panel capabilities enable you to capture transient behavior and to perform quick statistical analyses without a PC. The available Setup Integrity Checker software option allows you to compare the noise levels of different cabling and fixturing arrangements to help isolate external noise sources.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 15,50 kg
-
Product
Wind Power Solution
NXA GAMESA
-
The NXA GAMESA is custom-made with firmware and fixtures designed specifically for Gamesa turbines: G80x, G90x, G114, G126, G132, G145. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Power Cord Bending Tester
SW-6
-
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm SMB
45-720A-511
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm SMB
45-720A-751
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
Test Port Cable, 1 Mm
11500L
-
Connect test ports to devices, fixtures, or probe tips with this 24-cm cable featuring a return loss of 16 dB minimum.
-
Product
System Level Test and Burn-in Solutions
-
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
Product
Spectrum Analysis, Up To 26.5 GHz
S930902B
-
The S930902B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 26.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
-
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
Product
Flexible Probearm for HBM and Flex-Pitch Applications
TPA-GFG
-
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Flexible rotation of the probearm by precision gear 80:1*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
Product
Enhanced Time Domain Analysis With TDR
S96011B
-
Use S96011B to perform enhanced time domain analysis for high-speed data applications. Includes all functionality of the S96010B (TDR/TDT mode). In addition, the S96011B enables more detailed measurements and evaluations, such as eye diagram / mask modes, without adding PLTS software. Jitter and emphasis / equalization capabilities enable simulation of real-world signals and environment. The S96011B covers up to 53 GHz bandwidth. Full calibration is available and the automatic deskew ensures easy removal of fixture and probe effects. To get the best accuracy, use mechanical calibration kits or ECal with DC option (i.e. N469xD or N4433D with Option 0DC).
-
Product
Shielding Effectiveness
-
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
