Magnet
Attract iron and are surrounded by a magnetic field.
-
product
Wind Direction Sensor
ENVIROMUX-EWDS
Balanced wind direction vane with a near-zero friction bearing and a high accuracy magnetic angle sensor to provide precision wind direction. Sensor range: full 360 degrees , zero deadband. Accuracy: ±1.8 degrees. Resolution: 12 bit or 0.025 degrees. Directional Vane approximately 8 inches (203 millimeters). 3 wire flying leads, 25-feet (7.6-meter). Supply voltage: 4.5 to 5.5 VDC. Current: 15 mA typical. Output: 5 to 95% of input voltage (0.25 to 4.75VDC). Requires the ENVIROMUX-S5VDC-5V to operate with ENVIROMUX-2D/5D/16D. Maximum cable length: 1000 ft (305m)
-
product
Magnetic Flaw Detector (Magnetic Yoke)
NOVOTEST MPD-DC
Magnetic Flaw Detector (Magnetic Yoke) NOVOTEST MPD-DC applies in circumstances where the electric equipment mustn’t be used or prohibited by the rules.
-
product
Mini Cryogen Free Systems
mCFMS
Cryogenic offers cryogen free measurement systems, which include a cryocooler, cryostat with superconducting magnet (3, 5, 7 or 9 Tesla), variable temperature sample space, a selection of special probes for measurements of different physical properties, as well as electronics, computer and measurement software.
-
product
250 A Molded Case Circuit Breaker Tester
MCCB-250
The Vanguard MCCB-250 is a programmable, high-current source designed specifically for testing molded-case circuit breakers, thermal magnetic and solid-state overload motor-protection relays.
-
product
Nuclear Magnetic Resonance Equipment
SpecFIT HRC27
Low-field Nuclear Magnetic Resonance (NMR-DT) equipment with user-friendly interface software and data analysis under development. Compatible with Industry 4.0
-
product
Fluxmeter
480
An advanced tool designed primarily for use in industrial and measurement systems settings, the Model 480 fluxmeter measures total flux from which B, flux density, and/or H, magnetic field strength, can be determined.
-
product
Hall Effect Portable Gauss-Meters
300 Series
Integrity Design and Reseach Corp.
Typical Applications include Measurements of the Earth's field vectors, Air shipment inspection, Mapping and recording field perturbations, Magnet classification, Analysis of magnetic circuitry and components, Magnetic Resonance Imaging (MRI) and Measuring residual fields.
-
product
K Thermocouple Magnetic Contact Probe
TP757
Magnetic thermocouple type “K” probe for measurements on magnetic metal surfaces.
-
product
Hall Effect Measurement system
HMS-3000
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
product
Micro-Ohmmeters
Contact resistance measurement is one of the most important and common tests during switchgear manufacturing, commissioning and maintenance stages. Besides switchgear testing, the RMO digital micro-ohmmeters are designed for simple, safe and efficient testing of:disconnecting switches,high-current bus bar joints,cable splices,welding joints,and different high-current links in factory and high-induction field environments.All DV Power RMO micro-ohmmeters use Kelvin’s 4-point measurement principle which is the most convenient for very small resistance measurements. The measurements are accurate and in accordance with international standards for AC high-voltage circuit breakers testing (IEEE C37.09 and IEC 62271-100).Starting from 2003, DV Power has been a trend-setter on the market when our first 500 A micro-ohmmeter weighing only 8 kg (RMO500A / CPM500) was released.Currently, DV Power products portfolio includes 16 models, divided into 3 series:13 portable models: RMO-A (6) and RMO-G (7) series.6 handheld models: RMO-H (6) seriesThe instruments generate a user-selectable and ripple-free test current up to 800 A in an automatically regulated test ramp. Test current ramping significantly decreases the influence of the magnetic transients to measurement.
-
product
Non Magnetic Slides
Del-Tron’s new product line of Non-Magnetic ball slides provides the ideal solution for applications where magnetic interference cannot be tolerated. These lightweight Non-Magnetic ball slides are the perfect solution for medical, semiconductor, military and laser applications, just to name a few.
-
product
Vibrating Sample Magnetometer
VSM-P2H
This is low magnetic field type of exclusive use for soft thin film sample by the use of Helmholtz Coil.The type is capable of measuring variations of temperature from -50°C to 200°C by adding gas-flow type of temperature controller as an option.
-
product
Inductance Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Inductance Trainer comprises of a coil wound on a bobbin in which a magnetic material core moves as sensor. The displacement of the core is measured and displayed through a digital indicator.
-
product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45NK
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement*DC leakage current measurement*Least affection from the magnetization of core and temperature fluctuation*Convenient ＋24V single polarity power supply
-
product
Flexible Magnetic Field Probes
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
product
Fixed Gas Detectors
700 Series
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
product
AC Clamp Meters
Cambridge Instruments & Engineering Co.
A clamp meter is a clothespin-shaped instrument that can be clamped around a live wire in order to measure the current it's carrying. As a measurement principle, clamp meters detect the magnetic field emitted by current flowing in a wire in order to measure the current value.
-
product
DC BIAS CURRENT UNIT
3265B SERIES
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
product
Vector Manetometers
In the past, magnetic observatories relied on a combination of Overhauser, fluxgate and theodolite instruments for obtaining measurements. GEM then introduced the dIdD (delta Inclination / delta Declination) system for high precision results. Now, the dIdD has been enhanced significantly with the development of the Suspended dIdD system
-
product
Linear Slide
M-011
Physik Instrumente GmbH & Co. KG
M-011 ultra-high-precision magnetically-coupled stages use the force of integrated magnets to preload the bearing. This magnetic preload results in extremely uniform and smooth motion with minimum friction. Unlike conventional stages, where two bearings with limited parallelism guide the carriage (inducing runout and rotational errors) in M-011 stages, only one of the two linear bearings has a guiding function (V-groove) while the second bearing is for support only (U-groove).
-
product
Galvanic DO Electrode for DO and BOD Measurements in Laboratories
9521-10D
- Ideal for laboratory use- Integrated with built-in temperature sensor- Comes with replaceable 7544 DO Electrode Tip, detachable BOD bottle adapter and stirrer - Use magnetic stir plate during measurement- Waterproof
-
product
3-AXIS DIGITAL ELF GAUSSMETER: 20-4000 Hz
IDR-210
Integrity Design and Reseach Corp.
Typical Applications include checking the frequencies and magnetic fields (BW: 20-4000 Hz) produced by equipments such as computer monitors, television sets, power lines, induction heaters, industrial, scientific and medical equipment and household appliances, etc. Magnetic fields are invisible radiations, the best method to detect them is by using one of the accurate gaussmeter from Integrity Design & Research Corp.
-
product
Composite Inductors
Composite inductors are constructed by inserting a pre-wound coil over pre-press magnetic core and then pressing or molding a magnetic material around this assembly. The composite inductors are very similar to molded but typically offer lower DCR and lower overall losses. Our composite core inductors provide a fully shielded, high energy density, soft saturation solution for applications up to 120Apk. The construction enables the highest energy density of any available SMT inductors and also minimizes acoustic noise. We offer both commercial grade (-40C to 125C) and automotive grade (-55C to 155) in a wide range of platforms from 4x4x2mm to 17x16x13mm.
-
product
NMR Permanent Magnet
PM1055
A secondary field reference for NMR testing and Hall teslameters calibration.
-
product
Miniature Single-Stage Isolators – 780nm And 852nm
AOSense is excited to offer free-space optical isolators at 780 nm and 852 nm. The innovative, small package size enables integration into compact laser sources and amplifiers without sacrificing transmission efficiency. The low external magnetic field enables the isolator to tightly integrate into systems with high magnetic-field sensitivity such as atomic spectrometers, magnetometers, clocks, and cold-atom devices.
-
product
Metallic Probe Inductive Proximity Sensor
Shanghai Pubang Sensor Co.,Ltd.
1. All-in-one stainless steel housing design, strong anti-shock function2. Magnetic field interference, high switching frequency, wide temperature range3. Protection class IP67 (IEC)
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
Thin Film Composition and Thickness Monitor
P-1000
The Precision P-1000 readily analyzes compound thin films utilized in semiconductor, superconductor, magnetic and applications.
-
product
Speed Switch
M100T/M5000T
Features• Internal sensor• SPDT relay output• 5-100 rpm (M100T), 100-5,000 rpm (M5000T)• Terminal block for easy wiring• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs/wraps• Explosion proof (XP) housing• UL Listed Class I, Div I (C, D) Class II (E, F, G)
-
product
Cryogenic Temperature Sensors
Capacitance
CS capacitance sensors are ideally suited for use as cryogenic temperature control sensors in strong magnetic fields because they exhibit virtually no magnetic field dependence. Displacement current is not affected by magnetic fields. Consequently, temperature control fluctuations are kept to a minimum when sweeping magnetic field or when changing field values under constant temperature operation.
