Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
product
Bluetooth Recording Current Meter
RCM Blue
A self-recording dedicated current meter with Bluetooth for communications and data retrieval - now with the possibility to integrate a pressure sensor!The RCM Blue is a self-recording Current Meter which also measures water temperature in salt or fresh water, and a battery container with battery capacity up to 70Ah. .The Doppler Current Sensor is an upgraded version of the proven SeaGuard ZPulse sensor. The RCM Blue instrument configuration and data retrieval is done via Bluetooth which eliminates the need to open the pressure case for repeated deployments.RCM Blue has now been upgraded with the possibility to integrate a pressure sensor with a 0,01% accuracy. This simplifies your work significantly as you will know exactly where you are in the water column.
-
product
New Battery Resistance Tester
Hangzhou Xun Anda Electrical Co., Ltd.
maximum capacity of the battery:200AH/2000CCA(SAE)Voltage test range: 1.5-15VDCWorking voltage 1.5-15VDC,powered by the tested batterMaxim Power Consumption: around 0.5WOperating temperature: -10°C~50°C Operating humidity: 30%~90%, without condensationdisplay modes: Four different colors LED indicatorbutton: 3 buttons.Test Standard: SAE,DIN,EN,IEC,CA.
-
product
Cable Expert
AT/CX/CM Series
The VeEX® AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
product
Automotive & Industrial Cycle Testing System
CV
The CV is Bitrode's economical cycle life test equipment for the network based line of battery laboratory equipment. Designed to work with VisuaLCN Lab Client software, the CV provides standard or fully customized charge, discharge and rest cycles for automotive and industrial batteries. The Model CV is also useful for reserve capacity and charge acceptance testing with recharge.
-
product
Battery Impedance Tester
KVBT-15S
KV Hipot Power Test Equipment Co.,Ltd
Battery Internal Resistance Tester with advanced AC discharge measurement method, is applied to test accurately the voltage and resistance of battery capacity and state.
-
product
Battery Test Equipment
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
product
Battery Discharger & Capacity Tester
IDCE-CT
Fuzhou Fuguang Electronics Co., Ltd.
Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.
-
product
Battery Extra Load Units
BXL Series
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
product
Battery Load Bank
K-3980
Kongter Test & Measurement Co., Limited
Kongter offers a series of customized DC load banks with many different models for constant current battery discharge test and battery capacity test. They cover a wide voltage range from 12V to 480V nominal voltages with current up to 600A. They are widely applied in various industries. With its optional battery Data Acquisition Case (DAC), discharge values of EACH cell could be monitored in battery load bank and PC software simultaneously by using Kongter’s data view software.
-
product
Battery Tester
ZhangZhou Weihua Electronic co.,ltd
Is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition, namely its capacity for accumulating charge and any possible flaws affecting the battery's performance and security.
-
product
Battery Discharge and Capacity Testers
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
product
Battery Testers
Memory & Read FunctionRight Device to know the TRUE -LIFE of Battery Capacity (Resistive / Voltage) Simultaneously MeasureOn - Line Testing without shutting down batteryBuilt - in Comparator FunctionRates Conditions as PASS, WARNING or FAILDatalogging Memory FunctionCompact and lightweightRS-232 Interface & SoftwareAuto Power Off
-
product
Power Bank Tester
TOB-V-125
Xiamen Tob New Energy Technology Co., Ltd
Power bank tester test voltage current capacity (External battery pack tester machine).
-
product
Single Fiber Fusion Splicer
*Reversible monitor with control panel on each side*Color LCD monitor & 256 magnification*Compact & Light weight*Large capacity internal battery*Max. Wind velocity of 15m/s.*8 Sec. Splice time, 40 Sec. Tube-heat time*Simultaneous X and Y views*SYSTEM TEST ensures the best working condition*User programmable*Auto check fiber end face*Auto calibrate parameters*Store 8000 groups of splice results*Multiple language options
-
product
Frequency Conversion Rotating Magnetic Fla
MT-2XCF
MITECH MT-2XCF rechargeable frequency conversion rotating magnetic flaw detector is based on principle that the leakage magnetic field can absorb the magnetic powder. Make use of magnetic yoke magnetized the workpiece of ferromagnetic material. If there has defects it will produce leakage magnetic field that will adsorb magnetic powder. We could detect the flaw by observing the density of adsorption magnetic powder. It adopts large capacity lithium battery. By the inverter and the phase shifted signal processor to provide power for the detector, it solves the shortcomings of traditional magnetic particle detector relying on the 220V power supply. It has low power consumption and can continuous work for more than 6 hours. And the battery can be charged when the detector is on and off. Especially suitable for the field testing. It can choose the current frequency according to the flaw depth with unique frequency conversion communication design, that improve the detection sensitivity. It’s widely used in aircraft manufacturing, boiler and pressure vessels and other fields. It is a necessary professional precision instrument of quality control, in-service safety monitoring and life assessment.
-
product
Battery Analyzers
Beta D-50
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
product
Battery Discharger & Capacity Tester
Fuzhou Fuguang Electronics Co., Ltd.
Battery Discharger & Capacity Tester
-
product
Environmental Test Chambers
Bionic Scientific Technologies
Environmental Test Chambers offer precisely controlled environment required in insect and biological research, electronics production (battery testing and PCB manufacturing) and polymer testing (plastic and rubber testing) etc. Designed ruggedly and fitted with technology advanced instruments, our environmental chambers are available from benchtop cabinets to complex large capacity walk in rooms. At Bionics Scientific, we design and manufacture environmental chambers or climatic test chambers matching with customer required specifications and supply them worldwide at factory price.
-
product
20KVA to 200KVA Industrial UPS (3Ø – 3Ø)
NSP Series 20KVA to 200KVA
- Designed for powering critical Industrial and IT systems- DSP controlled IGBT based PWM technology- Design topology enables N+1 parallel redundancy- Industrial grade high speed CAN bus communication- User Friendly Matrix LCD and LED mimic front control and digital monitoring- Fully rated make before break maintenance bypass operation- Optional break-less load transfer via static switch- Low harmonic distortion- High crest factor tolerance and dynamic stability- Lower TCO- Continuous full rated power at ambient as high as 45°C- N+1 Parallel operation of UPS without any common hardware- Advanced Communication Capability (RS485/Modbus/SNMP)- High branch fuse clearing capacity- On-line battery bank test without load disconnection- Compact, elegant, and light weight enclosure- Easy installation with wheels for maneuverability and front bottom terminals
-
product
5KVA to 100KVA Industrial UPS (3Ø – 1Ø)
NSP Series 5KVA to 100KVA
- Designed for powering critical Industrial and IT systems- DSP controlled IGBT based PWM technology- Design topology enables N+1 parallel redundancy- Industrial grade high speed CAN bus communication- User Friendly Matrix LCD and LED mimic front control and digital monitoring- Fully rated make before break maintenance bypass operation- Optional break-less load transfer via static switch- Low harmonic distortion- High crest factor tolerance and dynamic stability- Lower TCO- Continuous full rated power at ambient as high as 45°C- N+1 Parallel operation of UPS without any common hardware- Advanced Communication Capability (RS485/Modbus/SNMP)- High branch fuse clearing capacity- On-line battery bank test without load disconnection- Compact, elegant, and light weight enclosure- Easy installation with wheels for maneuverability and front bottom terminals
-
product
Battery Internal Resistance Tester
HDGC-3915
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of battery capacity and technical status. The measurement data can be read on the instrument display directly. And it can also be uploaded to PC simply by using the USB drive. With the analyzing software, you could not only keep a record of the testing result but also have detailed analyzing for the status of batteries in different testing conditions.
-
product
Multi-Battery Tester
MBT-MIL
The ZTS MBT-MIL Multi-Battery Tester (MBT-MIL) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Battery Electronics
CAES Battery Electronics provide autonomous, dissipative, and continuous cell balancing to maximize available battery capacity, and therefore battery cycle life, throughout a mission.
-
product
Battery Discharge Capacity Tester
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
product
Multi-Battery Tester
MBT-1
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Life Cycle Module Testing System
LCN
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
product
6/12/24/36V Conductance Battery Tester
MBT300
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
product
Stationary Battery Comprehensive Tester
SAT-AG Series
Shaanxi Aitelong Technology Co., Ltd
SAT-AG Series Stationary Battery Comprehensive Tester is a kind of product introduced according to the market demand, which integrates the two major functions: on-line monitoring and capacity check test, with higher integration and better functions.SAT-AG is specifically designed for the maintenance of the lead-acid battery discharge in the electricity and telecommunication sector. It is a new high-tech intelligent product that provides safe, reliable and convenient constant testing equipment for the DC system(Direct current system) users.
-
product
Battery Discharger & Capacity Tester
IDCE-8X0
Fuzhou Fuguang Electronics Co., Ltd.
Wide Range: IDCE-8X0CT series can cover 10V~480V for multiple batteries test requirements like telecom (48VDC), powerutilities (110VDC, 220VDC), UPSs (300-60 VDC), traction batteries(12-96VDC)etc.
-
product
10 A True DC Micro-Ohmmeter
AUTO-OHM 10
The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for low-resistance-measuring applications such as the measurement of resistance in circuit breaker contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh, 3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per charge (10A/2 second duration) can be performed in the field. The Auto-Ohm 10 features a built-in charger that can charge the batteries when the unit is not in use.
