PCI Backplanes
-
product
PCI Edge Connector Card
PMC239/F
The PMC239/F also comes with a fan. The fan can be disconnected from its power if not needed.
-
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Five-Site Dual-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6567
Our Five-Site Dual-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6567) adapts five single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
product
PCI / PMC / CompactPCI Test System
PCITS
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Fanless Embedded System With LGA1150 Socket 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H81, 2 HDMI/ VGA/ DisplayPort, 2 GbE LANs, USB 3.0, CFast™ And PCI Express Mini Card
eBOX635-881-FL
The eBOX635-881-FL supports the 4th Generation Intel® Core™ i7/i5/i3 and Intel® Celeron® processor with Intel® H81 chipset. The super light yet compact eBOX635-881-FL comes packaged in an IP40-rated aluminum and cold-rolled steel enclosure and is designed to operate at temperatures ranging from -20°C to +50°C for use in the extremely environments. The fanless embedded system supports six jumper-less RS-232/422/484 and sixteen DI/DO ports along with three display outputs of two HDMI, DisplayPort and VGA for applications used in transportation, POS, kiosk, industrial control automation and medical equipment. Two PCI Express Mini Card slots are added to the system for greater expansion capability. One SIM slot is also available for 3G/4G, GPS, Wi-Fi and Bluetooth applications, allowing for more efficient networking options.
-
product
PCI Dual 20 X 4 Matrix 1 Pole Screened
50-511-021-S
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
product
3U Rackmount Appliance for PCI Express® Gen4
R300-G4
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols, such as PCIe, SAS, and SATA.
-
product
PCI Express 16 Reed Relay Output
8004He
The 8004He PCI Express digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The isolated inputs protect the PC and other sensitive equipment from the voltage spikes and ground loop currents that are common to industrial environments. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications.
-
product
11th Gen Intel Xeon Compact PCI Blade
CP6007-SA
CP6007-SA is based on 6-core or 8-core 11th Generation Intel® Xeon® processors with 10nm technology, with outstanding performance-per-watt values. Its scalable power budget allows users to tailor the power dissipation to their requirements. 32GB soldered memory and the option for an additional 32GB SODIMM with ECC is provided.
-
product
Compact PCI Bus Analyzer / Exerciser
CPCI650
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
product
PCI Express (PCIe) 5.0 and Compute Express Link (CXL) Protocol Analyzer
Summit T516
The Summit T516 is targeted at high-speed PCI Express 5.0 and CXL I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 1.81kΩ
50-298-022
The 50-298-022 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCIe-8430, PCI Express, 2-Port, RS232 Serial Interface Device
782122-01
The PCIe‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
product
12-Bit PCI Express ADC/Digitizer
SIS1350-2
The SIS1350-2 is the follow up unit to the SIS1350 digitizer card. It was developed for high repetition rate acquisition of short analog signals (i.e. up to 128 µs at 500 MSPS) with good resolution.
-
product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
product
Passive XMC-to-PCI Express Adapter
5934
The Technobox, Inc. P/N 5934 is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
Triple PCI Express, Hot-Plug Controllers
MAX5957
The MAX5957/MAX5958 triple hot-plug controllers are designed for PCI Express (PCIe)® applications. These devices provide hot-plug control for 12V, 3.3V, and 3.3V auxiliary supplies of three PCIe slots. The MAX5957/MAX5958s' logic inputs/outputs allow interfacing directly with the system hot-plug management controller or through an SMBus™ with an external I/O expander such as the MAX7313. An integrated debounced attention switch and present-detect signals simplify system design.
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
PCI Express Serial Boards
Sealevel PCI Express serial boards utilize 120-byte FIFOs for maximum reliability in data-intensive applications. Software developed for standard PCI boards will also work with Sealevel PCI Express boards, simplifying your transition to this next-generation PCI bus. Sealevel PCIe serial boards are configurable for RS-232, RS-422, and RS-485 electrical interfaces. These PCIe serial boards are fully compatible with X2, X4, X8, X16, and X32 PCI Express slots.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Express 4 Base Specification Receiver Test Automation
N5991PB4A
The N5991PB4A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 4.0 ASICs.
-
product
18-Port PCI Express
PEX 8733
The ExpressLane™ PEX 8733 is a 32-lane, 18-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8733 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
PCI To CardBus PCMCIA Type 1/2/3 Dual Slot Card, Ricoh R5C486 Controller
P222-Ricoh
The P222-Ricoh is perfect for use with Wireless LAN cards like WiFi / 802.11b or any of the newly emerging 802.11a or 802.11g standards and thanks to its second slot can simultaneously run a Bluetooth card or other type of PCMCIA or CardBus card.
-
product
PCI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device
779111-01
32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Thin Mini-ITX SBC With Intel® Celeron® Processor N3350, Dual HDMI, LVDS, USB 3.0, PCI Express Mini Card, MSATA And HD Audio
MANO311
The MANO311 is powered by the Intel® Celeron® processor N3350 (codename: Apollo Lake). Its customizable I/O interfaces, wide voltage and stunning graphics performance were designed to reduce time-to-market and facilitate quick deployment. The feature-rich MANO311 is an ideal solution for healthcare, automation, retail, digital signage and other Industrial IoT-related applications. The Intel® Atom®-based MANO311 has one 204-pin DDR3L-1867 SO-DIMM socket with up to 8GB of system memory; moreover, it supports 4GB memory down for options. It features one SATA-600 connector, one mSATA socket and one SDXC slot for storage devices. A wide range DC input of 12V to 24V makes the power input selection more flexible for a various applications. Furthermore, the newest mini-ITX motherboard features one PCIe x1 slot and one PCI Express Mini Card slot to enhance its expansion. Triple-display capability is available through the dual HDMI and LVDS.
-
product
PCI Express Oscilloscope Software Compliance Test
Rohde & Schwarz offers automated compliance test solution of PCI Express Gen 1.1, 2.0 and 3.0 interfaces. The test wizard of the Rohde & Schwarz ScopeSuite compliance test software guides the user via illustrated step-by-step instructions. The option supports add-in card and system motherboard testing. It is based on the PCI-SIG standard post processing analysis software and utilizes PCI-SIG test fixtures. A configurable test report documents the test results.
-
product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
