Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
product
Parallel Plate Dielectric Test Cell
LT-4203A
The LT-4203A Parallel Plate Dielectric Test Cell is designed for measuring the AC loss characteristics and permittivity of solid laminates and panels per ASTM Standard D150‑98, and implements the guarded electrode (three terminal) measurement preferred as the referee method.
-
product
Inductive Load Tester
4602-LV
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
product
RF Channel Simulators
Kratos Defense & Security Solutions, Inc.
The T400CS creates RF and/or IF signals that precisely match those that occur when transmitters and receivers are in motion with respect to one another. By accurately duplicating the motion effects and RF channel physics effects on an RF link, the T400CS allows bench testing of what once required actual motion and distance between a transmitter and receiver.
-
product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
product
Multifunctional Simulators
CCS600
Suzhou 3ctest Electronic Co.,Ltd.
CCS600 designed as a modular system is the most intelligent solution offering exactly what people need for full-compliant immunity tests against transient, surge and voltage dips. The max voltage is up to 6kV.
-
product
Capacitive Bank Load
Supreme Instrument Laboratories
Capacitive Bank Load Three phase suitable for operation on 415/440 volts three phase AC 50Hz housed in well ventilated sheet steel cabinet with bakelite front panel, complete with indicating lamps, voltmeter to indicate the input voltage and Ammeters to indicate, the load. ON/OFF switch, discharge switch etc. available in continuously variable type.
-
product
Motor Test Bench For No Load Test
The testing equipment is extensively used in industries for testing of motors under no load conditions.
-
product
NI Real-Time Test Cell Reference System
780590-35
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
product
Transportation Simulation Test System
KRD50 series
KRD50 series transportation simulation test system is to simulate the actual road conditions such as shocks and vibrations during the transportation of various items of a specific load, and to evaluate the effect of the actual working conditions on the loading, unloading, transportation, packaging, sealing or internal structure of the goods. In order to assess or confirm the products and packaging.
-
product
Flash Solar Simulators
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.
-
product
Unclamped Inductive Load Tester
ITC75300
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
product
Advanced GNSS Spoofing Simulation And Monitoring
SimSAFE
SimSAFE enables better protection against GNSS spoofing attacks. GNSS spoofing is a growing concern for developers and users of critical systems, with many well-publicized instances occurring every year. In order for users to be assured that their equipment continues to perform as expected when exposed to fake or replayed GNSS signals, it is vital to test thoroughly.
-
product
Torque Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S manufacturers two type of Torque transducers 1. In-Line Rotating Torque Transducers with / without speed sensors 2. Reaction Type Torque Transducers.*Transducer ranges from 1 Kg-m to 600 Kg-m with various types like Flange mount, Hallow type, Shaft mount, etc.
-
product
4kW Electronic Load
PT04-110
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 110V and 48V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
product
NIBP Simulator
vPad-BP
vPad-BP, part of the vPad-A1 family, is a NIBP (non invasive blood pressure) simulator designed to test the accuracy and repeatability of the NIBP function on Patient Monitors. User programmable settings allow for easy on site configuration to accommodate new models of NIBP devices.
-
product
Mechanical Simulation in Matlab
There are variety of numerical possibilities in the MATLAB and Simulink simulation environment. For those simulation environments we offer you various toolboxes that allow you to perform simulations easily and efficiently. These toolboxes can be combined with all available ways of MATLAB and Simulink. Our toolboxes can provide you support in the following areas: Analysis of structural dynamic behavior, Vibration and noise abatement, Design of active systems, Model Reduction, Ansys-Matlab interface.
-
product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
product
Test Cells (
LaplaCell
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They \re calibrated according to the methodology of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing.
-
product
LOADED BOARD TEST PROBES
SERIES-70
ElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35mA test current70 18 mOhms mean73 60 mOhms mean74 40 mOhms meanMaterials and FinishesPLUNGER: Heat treated beryllium copperor steel hardened to 55-60RC70 24Kt gold plated over nickel73 24Kt gold plated over nickel74 Rhodium plated over nickelBARREL: Nickel silver70 24Kt gold plated ID and OD over nickel73 No Finish74 24Kt gold plated ID and OD over nickel
-
product
Rack Mounted Load Banks
Traditional commissioning is a daunting task. Since formal system operation doesn’t begin until the system is commissioned, the commissioning team experiences intense pressure to complete the commissioning process quickly. Commissioning can involve high expense and requires staffs from different departmental disciplines to work together. For these reasons data center commissioning has almost uniquely been associated with large data centers (over 20,000 ft2 or 1,858 m2). In the recent past, many data center managers chose to roll the dice and perform little or no commissioning, relying only on start-up data to press ahead with launching the new data center. Given the reality of 24x7 operations, however, the alternative of exposure to major system failures and accompanying downtime is no longer an economically viable option. Commissioning has now become a business necessity. JUNXY series AC & DC rack mounted load banks can be used to introduce heat loads and to allow for simultaneous testing of both electrical and cooling systems.
-
product
Simulation Software and Test Solutions
Simcenter Software
Siemens Digital Industries Software
The Simcenter portfolio uniquely combines 1D simulation, 3D CAE and test to help you predict performance across all critical attributes earlier and throughout the entire product lifecycle. By combining physics-based simulations with insights gained from data analytics, Simcenter helps you optimize design and deliver innovations faster and with greater confidence.
-
product
Load Support Unit
LSU220A
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
product
MIMIC® Web Simulator
MIMIC Web Simulator creates a virtual lab with hundreds of simulated web servers. It allows you to easily develop and test your web clients, management and monitoring products. Having a virtual and scalable environment, you can try variety of scenarios to test your applications to assure your customers that your web services will work properly when deployed across heterogeneous environments. Best of all, you can reduce your lab budget significantly.
-
product
Fuel Cell Test Software
Exceptional functionality with a user-friendly graphical interface- Enhanced with our proprietary automation language, Emerald Software - Comprehensively manages the full range of FCATS fuel cell test system parameters- Simple user-friendly interface permits even novices to begin testing in minutes
-
product
HBM Discharge Simulator
PSD-510
The PSD-510 is a low cost, light weight, battery powered Human Body Model (HBM) simulator designed to help customers determine the HBM ESD sensitivity of a device in accordance with ANSI/ESDA/JEDEC JS-001.
-
product
Simulation Software For Cyclic Voltammetry
Digisim
Cyclic voltammetry can readily provide qualitative information about the stability of the oxidation states and the electron transfer kinetics of a redox system. However, quantitative studies using cyclic voltammetry (e.g., mechanistic investigations) are more difficult and typically require the use of simulation software. A number of methods have been developed for the simulation of cyclic voltammograms. Of these methods, the fast implicit finite difference method has been shown to be the most efficient, stable, and accurate, and this method is used for the DigiSim simulation software from BASi®.
-
product
Fuel Cell Test Systems
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
product
Partial Discharge Simulation Devices
Hangzhou Xihu Electronic Institute
Simulation device of cable PD faults, simulation device of switchgear PD faults, simulation device of GIS PD faults, simulation device of transformer PD faults.
-
product
High-accuracy Dual-channel Programmable Battery Simulator
N8352 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8352 series is specially designed for the R&D and testing of portable, battery-operated products , such as Bluetooth headsets, mobile, AR/VR smart terminals, electrical tools, etc. The current flows in both directions and can be used as either a power supply or a load. N8352 is easy for operation with touch screen and UI design. The output features are comparable to actual batteries, with fast dynamic response, no overshoot in voltage rise and fall, and stable waveform. The resolution is up to nA level, which can test the loop static power consumption, etc. N8352 can be widely used in the area of consumer electronics testing.
-
product
IBP Simulator
IBPS 2.0
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
