Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
Altitude Data Simulator
ADS-100
-
The Model ADS-100 is an all solid-state device that simulates the output of altitude encoders/digitizers in both parallel and serial (RS232) data formats. Designed to substitute for an altitude encoder when testing and troubleshooting an aircraft's altitude reporting system, the ADS-100 provides two RS-232 compliant outputs in addition to the ICAO pressure altitude code.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
PMC Module
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Air Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Five-Port Micro Sealed Electrochemical Cell
SF-1
-
Compact, fully enclosed glass micro-reactor (5–50 mL) designed for excellent mixing, stable mass transfer, and gas-tight electrochemical measurements. Ideal for high-precision studies, catalyst screening, and experiments sensitive to oxygen or moisture.
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
Product
PXI Electronic Load Module
Load Module
PXI Electronic Load Module provides the electronic load capabilities of sinking DC power with high-accuracy measurements in a compact form factor optimized for design validation, characterization, and production test.
-
Product
Robotic Sample Loading Systems
-
Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
Cell, Module & Pack Testing
-
Cell, Module and pack battery formats are crucial for electrification in transportation and energy. Arbin Instruments' test equipment is designed for performance-based tests, to meet the needs of these complex formats.
-
Product
High Power DC Electronic Load
3350G Series（4KW~6KW）
-
Each 3350G Series module has its own control and display panel, CC / CR / CV / CP /Dynamic modes, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
Production Caller ID Signal Simulator
AI-80
-
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
Product
Patient Simulators
-
Patient Simulators - also known as physiological simulators are essential tools for biomedical personals to accurately test and verify the performance of patient monitoring systems such as cardiac monitors, ECG machines. It simulates physiological parameters such as ECG, arrhythmia waveforms, blood pressure, respiration, temperature.
-
Product
NVH Simulation
-
With our NVH simulation tools, you experience your data in form of virtual test drives, thus speeding up the development processes. Auralize transfer path analyses based on test bench data or evaluate the NVH performance of a system even before components and assemblies can be physically combined.
-
Product
High Power DC Electronic Load（1250V）
36300E Series（50KW/60KW）
-
36300E Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
5V50mA Coin Cell Battery Test Equipment
TOB-5V50mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
Emulate Test in simulation
STIL-VT
-
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
Simulation Software For Cyclic Voltammetry
Digisim
-
Cyclic voltammetry can readily provide qualitative information about the stability of the oxidation states and the electron transfer kinetics of a redox system. However, quantitative studies using cyclic voltammetry (e.g., mechanistic investigations) are more difficult and typically require the use of simulation software. A number of methods have been developed for the simulation of cyclic voltammograms. Of these methods, the fast implicit finite difference method has been shown to be the most efficient, stable, and accurate, and this method is used for the DigiSim simulation software from BASi®.
-
Product
Manikins for realistic simulation of the acoustic properties of a human
Head & Torso Simulators
-
If you need to carry out realistic in-situ measurements of headphones, telephones or hearing aids, you need a Head and Torso Simulator such as the B&K ‘HATS’ – Type 4128D or GRAS’ Kemar to complete your test setup. These manikins have built-in ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. They are commonly used for tests on telephone handsets, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. Please contact your sales engineer or email sales@listeninc.com for more information.
-
Product
Troubleshooting Track Circuit Simulators
14900 Series
-
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
Product
Optical Components & Transmission Simulation Software
VPIphotonics Design Suite
-
VPIphotonics Design Suite™ embeds expert knowledge from our component and transmission design tools in one shared, flexible software environment to support requirements in design, analysis and optimization providing you with the most powerful numerical algorithms tailored for your applications.
-
Product
Test & Simulation Interface for PCI
PCI-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
Product
Electrochemical Cell Accessories
ECA-1
-
Replacement accessories for electrochemical cells, including electrode sealing screws, silicone gaskets, fixing rings, flange clamps, gas tubing, and related components. Compatible with a wide range of laboratory electrochemical systems.
-
Product
Radar・Sensor Simulation Framework
COSMOsim
-
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
Product
Regenerative Grid Simulator
61800
-
Chroma Systems Solutions, Inc.
Power rating: Up to 300kVA, single or three phase outputOutput Voltage: 0~330V L-N / 0~570V L-L0~400V L-N / 0~692V L-L opt. without using a transformerOutput Frequency: DC, 30Hz~100HzMaximum power delivered down to 200VAC L-NFull 4 quadrant, fully regenerative up to 100% of output current ratingSpecifically designed for PV inverter, Smart Grid and EV related test applicationsProgrammable slew rate settings for voltage and frequencyProgrammable voltage and current limitsTurn on, turn off phase angle controlLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetParallel output for higher power applications (three phase only)
