-
product
Telescopic Hot stick
HS-178
Standard Electric Works Co., Ltd
● Triangular-shaped design keeps sections aligned during extension and retraction● Push button release for stick extension and retraction ● Telescopic design allows for easy assembly, storage and transportation● Lower push button fix position for better support of the telescopic hot stick● Withstands voltage rating of 100kV from 30cm for 5 minutes ● Universal end fitting accepts a wide variety of standard attachments● High-visibility yellow tip section● Easy-to-replace sections● Carrying bag included ● Optional integrated height measurement scale● Complies with IEC 62193 safety standard
-
product
AC/DC Digital Clamp Tester (CE)
M-270
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Auto zero adjustment for DC current offset.*Conform to IEC safety requirements.
-
product
IEC 61000-4-5 EN61000-4-5 Lightning Surge Tester, Surge Generator
506AX
Shenzhen Chuangxin Instruments Co., Ltd.
Automatic lightning surge generator (or Lightning surge immunity) is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
-
product
HMM+™ Tester
Model 4702
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
LST-2000 Laser Safety Test System
Hangzhou Everfine Photo-E-Info Co., LTD
The system can measure the spectral power distribution, radiant power, radiant energy, apparent light source size, pulse energy and other parameters of the laser light source, and classify the laser light source according to the standard IEC 60825.1. Because laser measurement involves more condition parameters, limit calculation and judgment process is complex, so this system adopts systematic design, the measurement complexity is simplified, the hardware adopts componentization module, users only need to follow the software prompts, carry out the corresponding steps of operation can accurately measure the effective radiation value under the corresponding conditions. The software calculates the relevant reachable emission limits and automatically classifies the laser product's safety level.
-
product
Regenerative AC Emulator, 600 VAC, 63 A, 30 KVA, 3‑Phase
SL1201A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Plug Socet & Cord Testing
Educated Design & Development, Inc.
Flexing Tests: On flexible cables (or cords sets with fitted plugs), electric tools or hand lamps. Meets requirements of standards such as IEC 60335, IEC 60227, IEC 60745 and UL745. This product is for continuous bending tests of cables or cord sets fitted with plugs. The model F39 allows the simultaneous testing of two samples in it's standard version. This not only allows for substantial time savings, but also allows for the testing current circuits to be simplified by looping through the cables.
-
product
SRJ (for IBP sensors)
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
product
Reach-In Solar Panel Test Chamber
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
product
Smart Polyglot - Wireless Probe
Signals & Systems India Private Limited
Smart Polyglot is designed to talk to meters of all protocols – PACT, ANSI, IEC. Not only does it talk over optical media, it interfaces with IR, IrDA meters as well, making it the only device that talks to any type of meter in any language.The Smart Polyglot has a wireless Bluetooth interface and enables seamless use with any DOS, Android, or Windows based devices with Bluetooth support. This Smart Polyglot Bluetooth probe can detect the commands from Bluetooth connected devices and establish a connection automatically for meter reading applications.
-
product
Protective Relay Test Kit
PW460
PW460 Protective Relay Test Kit is the comprehensive protection relay testing equipment for all types of protective relays with high accuracy. This relay test kit has in-built output monitoring and recording function and supports testing IEC 61850 digital relay.
-
product
19" Subracks
Elma implements quickly and easily scalable, robust 19'' subracks, card cages or rackmount chassis for the use in just about any industry or environment: Industrial automation, test & measurement, transportation, energy, defense, communications and medical. The products of Elma Electronic support standards such as IEC, IEEE or AdvancedTCA.
-
product
Headphone Test Fixture
AEC206
The Larson Davis Model AEC206 Binaural Test Fixture is the tool for testing supra-aural, circumaural, supra-concha, intraconcha, and insert-type headphones. Preassembled with IEC 60318-4 (711) occluded-ear simulators and TEDS compatible preamplifiers that provide electronic calibration information, the Model AEC206 is user-friendly and easy to learn. Additionally, calibration is a simple process—a custom adapter is included for the Model CAL250 acoustic calibrator or similar device.
-
product
Trip, Auxiliary and Supervision Relays
Delta Series
The Delta relays provides a robust and reliable interface between protection and control system circuits. A more economical alternative to traditional auxiliary, trip and supervision relays, the Delta provides a compact, flexible and high performance solution while meeting relevant IEC standards.
-
product
110kV/220kV Substation Series Testers
JYH-C
The JYH-C CT & PT Analyzer is a multifunctional device for testing current and potential transformers, covering excitation, ratio, polarity, resistance, and more. It meets IEC standards and features L
-
product
Short Hot Stick
HS-800
Standard Electric Works Co., Ltd
● Single foamed hot stick.● Universal sunrise fitting on the head to fit special tool fittings.● Rated at 100 kV per 300mm (5 minutes).● Can be connected to 275 HP HV proximity detector, 21X HVD capacitive HV detector and 277 HP Non-contact HV detector.● Meets IEC 60855.● Reasonable price.● Accessories
-
product
Capacitor Contactor
KML
Lifasa - International Capacitors, SA
The new KML contactors are designed in accordance with IEC 60947-1 and are suitable for the connection of three-phase power capacitors. Thanks to its pre-load block mounted on the same contactor, the strong current tips produced at the moment of capacitor connection are reduced and the contactor itself is protected at the same time.
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
Protection Test Set
CMC 850
The CMC 850 is a protection test set dedicated to IEC 61850. It focuses on the real-time communication methods GOOSE and Sampled Values to interface with the devices under test.
-
product
Electrical Safety Test Equipment
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
product
Fanless Embedded System With Intel® Atom® Processor E3845 For Railway, Vehicle And Marine PC
tBOX100-838-FL
The tBOX100-838-FL is certified with E-Mark and ISO 7637 for vehicle applications. The rugged tBOX100-838-FL comes with the onboard low power quad-core Intel® Atom™ processor E3845 along with onboard DDR3L memory up to 4GB. The compact vehicle PC features five BNC connectors with four video-in and one audio-in as well as one capture card for DVR surveillance applications. The capture SDK is ready and integrated to support system integrators to speed up the solution development. In addition, it was designed to withstand a wide temperature range from -40°C to +60°C and vibration up to 3 Grms, equipped with intelligent power management at wide voltage range 9-36VDC. The tBOX100-838-FL is also compliant with EN 50155, EN 50121, DNV 2.4, and IEC 60945 for use in rolling stock and marine industries. The cost-effective embedded system adopts a heavy-duty aluminum extrusion and steel case to withstand the rigors of day-to-day operation. The compact size of the fanless transportation computer ensures that it can fit into a variety of space constricting environments. To ensure that the system can be integrated into various locations, the tBOX100-838-FL supports DIN-rail and wall mount. The feature-rich system is ideal for security surveillance, transportation controller, data transfer and management.
-
product
MCB Endurance Test Bench
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
product
20KV 30KV Electrostatic Discharge Generator ESD
ESD-202AX
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performan
-
product
Circuit Breaker Test Equipment
DV Power has released a new generation of circuit breaker test equipment for condition assessment of medium and high voltage circuit breakers.Field-portable instruments with standalone or PC controlled functionality, allow performing various tests during circuit breaker manufacturing, commissioning and maintenance stages.Applications supported by the DV Power test equipment include measurements of:Contact resistanceDRM (dynamic resistance measurement)Coil resistance and coil current (IEC 62271-100)Mechanism charging time (IEC 62271-100)Minimum trip voltage (IEC 56, ANSI C37.09)Undervoltage release (IEC 60694)The timing of a circuit breaker’s main, auxiliary and pre-insertion contactsSynchronization between the contactsMotion and velocity“First trip” testThe essential part of a circuit breaker condition assessment is the ability to compare the latest test results with the previous testing. Accordingly, our instruments store measured values and compare them to a manufacturer’s limits. Also, a fingerprint obtained in this way can be used at a later stage as a reference during subsequent measurements. In order to obtain an accurate comparison, the tests need to be performed using identical test parameters. Consequently, any deviation and change in the test results may indicate the circuit breaker condition deterioration. Even more, to overcome this issue, DV-Win enables test plans and graph overlay features.Finally, as a final result of a circuit breaker maintenance process, the DV-Win provides analytical tools and customized report creations.
-
product
NED-LMD Near-Eye Display Measurement Systems
NED-LMD E-Series
The world’s most comprehensive test systems to completely characterize augmented reality, virtual reality, mixed reality, and heads-up displays (AR, VR, MR and HUDs) by truly emulating the human eye and conforming to the latest standards being developed by the IEC and SID.
-
product
3.0mm Preset Controls Probe
CX-A3C
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
product
Optical Spectrum Analyzers
FTBx-5245/5255
Robust In-service Pol-Mux OSNR for 100G/200G/400G (FTBx-5255). Industry’s only all-in-one OSA covering all applications: high speed (100G+ In-service OSNR, etc.), CWDM, O and L-band testing, etc.Portable solution for spectral characterization of DWDM/CWDM networks. Industry’s smallest OSA/transport solution in a single platform (FTB-4 Pro). Pol-Mux OSNR option compliant with IEC 61282-12 standard.
-
product
Medical Box PC With IEC 60601-Compliant NVIDIA IGX Platform
MLB-IGX
- GPU: 2,048-core NVIDIA Ampere architecture with 64 Tensor Cores- CPU: 12-core Arm® Cortex®-A78AE v8.2- Up to 1,705 trillion operations per second of AI performance- NVIDIA® ConnectX®-7 smart network interface card (SmartNIC)- Ten years of NVIDIA® hardware and software support
-
product
Lightning Impulse Simulation Tester
KT-6030iG
Most of all electric systems and equipments are weak against the lightings(direct, inductive lightning). In fact, those electric equipments are broken mainly by lightning.This Lightning Impulse Simulation Tester is certificated to IEC 61000-4-5, and generates the similar impulse with huge rush currents and tests the safety of the power systems and equipments.
