Magnetic Field
an force around magnets, electric current and atomic orbits.
See Also: Magnetic, Magnetic Test, Magnetic Head, Magnetic Susceptibility, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field, Magnetic Field Mapping, Magnetic Field Meters, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test, Helmholtz Coils
-
Product
Continuous Magnetic Measurement Equipment
CWM
-
The automatic measurement equipment to continuously measure magnetic property in commercial power frequency of magnetic steel sheet sample on line, is used for quality control. Core loss in definite time of magnetic flux density [B] or magnetic flux density [B] in definite time of strength of magnetic field [H] for excited magnetic steel sheet is measured on line.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
TMR Angle Sensors
-
MultiDimension Technology Co.,Ltd.
Angle sensor are proportional to the sine and cosine of the angle of a magnetic field applied parallel to the surface of the sensor, which can be provided by a small magnet positioned above the device.
-
Product
USB Magnetometer
-
MultiDimension Technology Co.,Ltd.
A three-axis digital magnetometer that is intended for the measurement of magnetic fields near the probe tip at frequencies less than 250 Hz.
-
Product
Three Channel AC Magnetic Field Signal Conditioner
TCM-1A
-
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
-
Product
Micro probes 1 MHz up to 6 GHz
MFA 01 set
-
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
Flexible Leakage/Line Current Tester
RLM-10+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Highly Sensitive Magnetization Switching Evaluation system
FMSS
-
The necessity of evaluation for media by thin film and high speed magnetic recording increases as high density of magnetic recording media. This equipment is newly-developed one which applies any time-range and pulse magnetic field to test sample, and detect magnetization after applied with highly sensitive resonating sample magnetometer.
-
Product
Miniature Fluxgate Magnetometer
WFG-140
-
The WFG-140 magnetometer is a complete 3 Axis Fluxgate Magnetometer system packaged in a rectangular package of dimensions 1.5\"x1.5\"x4.65\". With low noise and small size, the instrument can be used wherever small magnetic fields (3 x 10-7 to 1 Gauss) need to be measured.
-
Product
Electronic Ammeters
-
The device puts out a voltage that is proportional to a magnetic field to which it is exposed.
-
Product
High-Dynamics PIMag Linear Stage
V-522 • V-524 • V-528
-
Physik Instrumente GmbH & Co. KG
Reference-class linear stage. Linear positioning stages with magnetic direct drives largely dispense with mechanical components in the drivetrain and the drive force acts directly on the motion platform. Together with precision bearings, a high travel accuracy and longer lifetime is achieved. The linear positioning stages are particularly suitable for scanning applications. PIMag® Voice Coil. Voice coil drives consist of 2 essential components: A permanent magnet and a coil, which is located in the air gap of the magnetic field. When current flows through the coil, it moves in the magnetic field of the permanent magnet. The direction of motion depends on the polarity. Thanks to their low weight and friction-free drive principle, voice coil drives are particularly suitable for applications, which require high dynamics and high velocities at limited travel ranges. High scan frequencies and precision positioning are also possible with these drives, because they are free of the effects of hysteresis.
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
e-Compases
-
Designed to accurately detect the direction and magnitude of external magnetic fields, ST’s eCompasses use accelerometer measurements for tilt compensation, thus ensuring very accurate compass headings even when handheld or mobile devices are inclined.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-110S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
NMR Precision Teslameter
PT2026
-
Nuclear Magnetic Resonance is the most precise technology to measure magnetic fields, and the PT2026 is the most precise NMR magnetometer on the market. In optimal conditions, it achieves a precision of under ten parts per billion! But precision is just one of the features brought by the PT2026: high fields, robustness to inhomogeneous fields, 33 Hz measurement speed, improved search time – the list goes on. The key is an instrument design, using modern RF and computer technology. The result is an NMR magnetometer that opens up a host of new application areas. Magnetometer Gaussmeter
-
Product
Loop Antennas
-
A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements,
-
Product
Hall Effect Speed Sensors
-
SPECTEC Innovative Sensor Solutions
SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.
-
Product
HandyScope HS6-DIFF With EMI & SafeGround: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMEG-W5
-
The powerful capabilities of the WiFiScope HS6-DIFF-1000XMEG EMI analyzer give the user the possibility to quickly perform a good EMI compliance test. With this cost effective test, time and money are saved by avoiding extra visits to expensive EMC testing facilities. The supplied EMI probe set TP-EMI-HS6 contains three magnetic field (H field) probes and one electric field (E field) probe. The tripod ensures that the probes can be positioned properly at the object under test.
-
Product
Magnetic Probing Systems
MPS-C-300 and MPS-C-350
-
MicroXact’s truly unique patent-pending design enables wafer-level testing of spintronic devices, nanoscale electronics and many other materials and devices where magnetic fields are required for accurate test and measurement.
-
Product
TMR Gear Speed Sensors
-
MultiDimension Technology Co.,Ltd.
Magnetic gear tooth sensors utilize a unique push-pull Wheatstone bridge design, including one or two Wheatstone full bridges, with four or eight unshielded high sensitivity TMR sensing elements. The Wheatstone bridge creates a differential voltage output with respect to the magnetic field gradient along the sensor’s sensitive direction.
-
Product
Magnetfield Testers
-
The magnetic field tester is suitable for rapid and precise testing of electro-magnetic switches and valves. Their tip lights up to indicate the presence of permanent, DC or AC magnetic fields. Thereby, they are so sensitive that very often it is not necessary to remove covers or cladding from machines and the function check can be carried out without any setting-up time or stopping the machine.
-
Product
3 AXIS DIGITAL ELF 50/60Hz AC GAUSSMETER, FWBELL
4100 Series
-
Integrity Design and Reseach Corp.
Typical Applications include checking the 50 and 60 Hz magnetic fields (EMF) produced by equipments such as AC Power Lines, Office Equipment, Video Display Terminals, Household Appliances, home and Building Inspection, etc.. Magnetic fields are invisible radiations, the best method to measure the strength fields is to use one of the accurate gauss meters offer by Integrity Design & Research corp.
-
Product
Vacuum Interrupter Pressure Integrity Test Set
-
Low Drift Current is measured by applying magnetic field.
-
Product
Vibrating Sample Magnetometer
VSM-P2H
-
This is low magnetic field type of exclusive use for soft thin film sample by the use of Helmholtz Coil.The type is capable of measuring variations of temperature from -50°C to 200°C by adding gas-flow type of temperature controller as an option.
-
Product
Magnetic Sensors
-
Magnetic proximity sensors are characterized by the possibility of large switching distances, available from sensors with small dimensions. They detect magnetic objects (usually permanent magnets), which are used to trigger the switching process. As the magnetic fields are able to pass through many non-magnetic materials, the switching process can also be triggered without the need for direct exposure to the target object. By using magnetic conductors (e.g., iron), the magnetic field can be transmitted over greater distances so that, for example, the signal can be carried away from high temperature areas.
-
Product
Hand Held Needle Detector
UI-G60
-
Hand held needle detector, using the principle of magnetic field, can accurately detect the specific location of ferromagnetic metal impurities such as broken needles, which is very suitable for the inspection of thin and small items. It is also suitable for the detection of large needle detectors. It can accurately find the position of steel needles or ferromagnetic metals in a small range with this hand-held needle detector, avoiding the damage of metal impurities to consumers and manufacturers, and improving the quality of enterprise products.
-
Product
Single Axis AC Magnetic Field Sensor
MGCH-2
-
Macintyre Electronic Design Associa
The MGCH-2 is the lowest noise, highest sensitivity single axis AC magnetic field sensor available for the measurement of sub radio frequency fields. Because of its innovative design, the MGCH-2 amplitude response is insensitive to the frequency of the field over its 10 Hz to 100 kHz frequency band. Accuracy at 10 kHz is 0.1 dB, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Fluxgate 150A Current Sensor
LF03
-
Our LF03 current sensor works with the dynamic Fluxgate measurement technology. It is characterized by its simple, practical design and prevents high temperature drifts. Fluxgate technology uses the phenomenon of magnetic saturation to modulate the measured magnetic field and convert it into an electric field.
-
Product
Cryogenic Temperature Sensors
Interchangeable Rox™
-
Ruthenium oxide temperature sensors are thick-film resistors, with most models suitable for use in magnetic field applications. These composite sensors consist of bismuth ruthenate, ruthenium oxides, binders, and other compounds that allow them to obtain the necessary temperature and resistance characteristics. Each Lake Shore Rox™ model adheres to a single resistance versus temperature curve.
