Filter Results By:
Products
Applications
Manufacturers
Open Short
Pinpoint open circuits.
-
product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
LAN Cable Tester
21-6566-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
Motor Winding Ohmmeter
RMO-M Series
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
product
LAN Cable Tester
Is a hand-held test instrument that lets you verify and troubleshoot the LAN cable of twisted pair. It displays graph wire-map, opens, shorts, miswires, split pairs and the remote ID number all on one screen.
-
product
ELECTRONIC CIRCUIT TRACER
PPECT3000
*Locate short and open circuits without having to remove plastic panels, molding and carpet*Traces shorts and open wires with visual navigation and sound indicators*Pinpoint shorts, open circuits, switches and breaks in wires
-
product
Circuit Breaker Tester
LAN & Breaker
Find opens, shorts and mis-wired cable installations with quick go/no-go tests, using an Amprobe LAN tester. Identifying circuit breakers is efficient when you use an Amprobe breaker tracer.
-
product
3-in-1 OSL Mechanical Calibration Kit, DC To 50 GHz, 2.4 Mm (m)
85564A
The 85564A 3-in-1 mechanical calibration standard combines an open, short and load standard in a compact unit. The product is small, easy to handle, and lightweight. All standards in the 85564A are male 2.4 mm.
-
product
Cable Continuity Detectors
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Cable Continuity Detector can test the open circuit, short circuit, crossover and continutiy for RJ11/RJ45/BNC/USB cable, and the test result is displayed by the visible LED light status.
-
product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
4-in-1 OSLT Mechanical Calibration Kit, DC To 9 GHz, Type-N(m), 50 Ohm
85514A
Easily calibrate non-insertable devices with a type-N (m) 50 Ω open, short, load, and through in a compact unit
-
product
Rack Mount Audio/Lighting/Network Cable Tester
AudioJog Rack 8
There are 2 rows of 9 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
1 Mm Calibration Kit
85059B
The Keysight 85059B is a 1.0 mm calibration kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. The opens, shorts and loads in this kit are optimized to provide accurate and traceable calibrations over the specified frequency range. The 85059B with 85059V 1 mm Verification kit are replacements for the 85059A 1 mm calibration/verification kit.
-
product
Network Toner & Probe Kit
MT-7028
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (m)
85562A
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight
-
product
4-in-1 OSLT Calibration Kit, DC to 40 GHz, 2.92 mm (m)
CK562A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Low Voltage Testers
Device used to identify opens and shorts in applications that are driven on low voltages.
-
product
Milliohm Meter
MO-100
Diagnose potential failure with the MO-100, portable battery powered milliohm meter. Quickly check windings opens or shorts in motors, generators and transformers, wire-to-wire connection resistances, heating elements testing and contact resistance in critical electrical connections.
-
product
An IEC 61000-4-11 Full Compliance Voltage Dip SimulatorModel: VDS-2002
VDS-2002
NoiseKen's new VDS-2002 offers easy and accurate test and following features: Dip, swell, interruption and variation tests up to 16A 240V single-phase AC, interruption test up to 125V DC, preset levels 0%/40%/70%/120%, open and short mode selection for interruption and optional Windows software.
-
product
Cable Fault Locators
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
product
Actuation Methods for In-Circuit Test Fixtures
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
product
Cable Tester
WEETECH offers a number of individual testers for the low voltage open test and short test.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
HDMI Cable Tester
MT-7062
Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.
-
product
Automatic and Accurate Inspecting Systems
Circuit AOI
The Circuit AOI system is designed to perform automatic and accurate inspecting systems. It integrates rigid mechanical system with advanced vision technology and manufactured and tested by strict is standards. It is suitable for circuit inspection for PCB/FPC, verification and repair. Innovation and unique inspection algorithms are applied to inspect open, short, protrusion, nick, scratch, pin hole, island, line width/space violation, object missing and others defects. AOI system can use offline setup project and check results. It will improve the throughput.Compare to halogen lighting, the full angle LED lighting of Circuit AOI can obtain the best image contrast and is good for different panel type inspection.
-
product
Hand-held Cable Tester
STM-8
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
product
Open-Short-Load RF calibration kits
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
product
Lan CAble Testers
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
