Filter Results By:
Products
Applications
Manufacturers
-
product
Robotic Inspection Vehicle
Iris Power RIV800
The Iris Power RIV800 Robotic Inspection Vehicle and Camera System, allows a visual inspection of the generator stator and rotor, including checking the air vents for debris, with or without removing the rotor. The robotic inspection vehicle also provides an automated means of EL CID electromagnetic core imperfection detection testing and SWA stator wedge analyzer testing.
-
product
Field Ground Module
SEL-2664
Schweitzer Engineering Laboratories, Inc.
Add the SEL-2664 Field Ground Module to the SEL-300G or SEL-700G to protect all the critical components in your generator with one comprehensive relay. Or, add the SEL-2664 to the SEL-2664S to complete ground fault protection on both the rotor and stator.
-
product
Motor Test for Electric Scooters
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
product
Rotor Balancer
Static and Dynamic Balancing of Rotating MachinesBalanced rotors are essential for the smooth operation of rotating machinery. Unbalance will create high vibrations, reducing machine life and causing material defects. Our single and dual-plane balancing tool is a great tool to eliminate unbalance on-site reducing long down times.
-
product
Capsule Slip Rings
Capsule Slip Rings are compact slip rings that can be used in a wide range of applications. They integrate rotor, stator, brush block, bearings and casings and enable the transmission of power and data through rotating systems. They are ready to be integrated into customers’ systems and provide built-in protection from humidity and dust.
-
product
Motor Test Instruments
The absorbed energy of the DCE series Dyno is converted into heat in two rotors located at the external side of the coils . The rotors are designed with curvilinear cooling fins for fast dissipating heat into the atmosphere . This design provides with the smallest physical size for air cooled Eddy-Current Dyno . Simple construction and desirable speed-torque characteristics are adaptable to most of the applications.
-
product
Magnet Testing
RMP Rotor Measuring Station
The RMP Rotor Measuring Station is a universal measuring system for the precise measurement and quality control of multi-pole permanent magnet rotors.
-
product
Electric Motor Checker
CIE/1001
Cambridge Instruments & Engineering Co.
Housed in attractive wooden body with sunmica finish. For comprehensive check of Rotor and Stator Inductance, Resistance and Insulation Resistance without dismantling the Motor. Only to isolate the power supply.
-
product
Helicopter FADECs
The EMC-100 is dual channel Full Authority Digital Engine Control (FADEC) system, designed for helicopter turboshaft engines. The electronic control unit’s (ECU) primary channel provides precise engine power management and rotor speed control throughout the operational range of the engine. The reversionary backup channel provides full mission capability should a primary system failure occur.
-
product
Dynamometer
Water Brake Series
The Water Brake (WB) Series Dynamometers are designed with aggressive rotor fin technology that allows for higher torque without the need for multiple rotors. The 0-4000 RPM range and high torque capacity make this dynamometer series an excellent choice for testing a wide range of motors from low RPM DC motors to 2 pole AC motors.
-
product
Measuring Stations
The main application is the measurement of the flux density on the surface of multipole magnets or components with magnets. A large amount of measuring stations is built for rotors.
-
product
Turbine Flow Meters
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
product
Magnetizer
MAGNET-PHYSIK Dr. Steingroever GmbH
Use our magnetizers for everything from the smallest rotors in a wristwatch to wind turbines. We magnetize magnets and magnetic materials of all sizes.
-
product
Enhanced Vision Systems
Elbit Systems of America’s Degraded Visual Environment (DVE) solution uses intuitive 3D grid symbology along with a helmet tracker to provide critical helicopter/tilt-rotor cues during brownout operations. This system, which is an upgrade to the head-up display installed on many military helicopters, removes weight or drag penalties by eliminating nose-mounted sensors. The helmet tracker provides numerous ancillary benefits such as depicting the other pilot’s Line of Sight (LOS) for improved crew coordination, as well as providing the ability to slew weapons or optical payloads to the pilot’s LOS, hands-free and heads-up.
-
product
Analytical Gear Inspection Machine
KNM 2X / 5X series
Analytical gear inspection machine for workpieces up to Ø 650 mm. Measuring machines for spur and helical gears, rotors, bevel gears, gear tools, shafts etc. Ultimate highly precise measurement of smaller size gears in the lab or on the shop floor - no foundation required.
-
product
Wind Speed Anemometers
Comptus A75-101 and A75-104 Wind Speed measurement anemometers are built with durable injection molded polycarbonate rotors and housings, and utilize a fully hardened beryllium copper shaft.
-
product
Electric Attitude Gyroscopes
5000EG-series
The 5000EG gyro is based on our air-driven 5000B model, whose proven reliability has made it the industry standard for many years. There are two models available: 14 and 28 VDC. The rotor is precisely machined from a heavy-metal tungsten alloy, which has a higher mass than brass, contributing to the instrument’s demonstrated stability. The electric motor is driven by a built-in power inverter, and has an integrated air-erection mechanism. A warning flag is deployed upon loss of primary power. During acrobatic flights or short stops, the gyro’s mechanism can be caged whenever the knob is pulled.
-
product
Torque Sensors
A device for measuring and recording the torque on a rotating system, such as an engine, crankshaft, gearbox, transmission, rotor, a bicycle crank or cap torque tester. Static torque is relatively easy to measure.
-
product
Slip-Ring Motor Starting Panels
Rotor Starter
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into some steps and controlled via contactors by motor starting control system. As the motor speed increases, the external rotor resistors are eliminated by shorting contactors until all external resistors are shorted out.
-
product
Mooney Viscometer
SMV-301/301RT
The SMV-301 / 301RT allows the user to measure the Mooney viscosity, scorch time, minimum Mooney viscosity, and other characteristics of rubber in accordance with JIS, ISO, and ASTM test methods. With outstanding temperature recovery characteristics and easy operability, it can also be used for stress relaxation measurements or for tests that involve varying the rotor speed.
-
product
DC Coreless Motor
Adamant Namiki Precision Jewel Co Ltd.
There is a structure in the cage shape by only the copper wire turns around a cylindrical permanent magnet placed inside It is a feature. There There is not an anron core, it does not receive the action of the copper basket type rotor is light, the moment of inertia becomes small, so quick response is possible. A Permanent Magnet, There Is No Cogging, That Is, Rotation Is Smooth, And Vibration And Noise Can Be Reduced. - Since Rare Earth Magnets With High Magnetic Properties Are Used And The Rotor Is Formed Only With Coils, The Motor Itself Can Be Made smaller and lighter.
-
product
Automated Engine Testing System
Automated engine test system is intended for comprehensive testing of electrical motors with shaft rotation frequency up to 70 000 rpm. Such engines include:*high-voltage motors;*traction engines;*internal combustion engines;*AC motors;*DC motors;*synchronous engines;*asynchronous engines;*asynchronous engines with short-circuit rotor.
-
product
Rotor Test Systems
Automation Technology's RTS-3800 Rotor Test Systems offer an unparalleled ability to test the quality of die cast or PM rotors. The RTS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems; the RTS-3800 is backed by ATI's industry leading two-year limited warranty.
-
product
Moving Die Rheometer
SG-S05A
It tests the feature about vulcanization and searches for the best suitable vulcanization time.It adopts digital intelligent temperature-controller to adjust and sets easily.Its stability, reappear and accuracy is better than the general rotor rheometer.The microcomputer uses import CMOS chip which has high dependability.It draws、calculates and prints automatically,and has copy or blowwing up function. It adopts computer-control and interface to collect、store or deal with data and print test result .This machine's function is better than other types and shows high automatization features. It has functions about curve-comparing and blow up.It uses series of windows operation system flat and graphical software operation interface.The data is dealed with much truly.The user's test operation becomes faster, flexibly and protect conveniently.
-
product
Knopp Phase Sequence Indicator
K-3, K-6, and K-7
Use of the Knopp K-3 Phase Sequence Indicator saves man-hours and protects valuable equipment against damage. It pays for itself in a short time. Specially designed induction motor unmistakably indicates the phase sequence by direction of rotation or rotor disc.
-
product
Magnetizer
U-Serie
MAGNET-PHYSIK Dr. Steingroever GmbH
The pulse magnetizers of the U series are suitable for a wide range of applications in the laboratory and in production. With low energies, they are ideally suited for sensor systems made of ferrite material, which can be magnetized with short cycle times at currents of up to 20 kA. In the energy classes 1,400 Ws and 2,800 Ws, rotors with NdFeB magnets up to a diameter of approx. 60mm are typical applications. With this device, you can magnetize with pulse currents of up to 60 kA.
-
product
Integrated Turbine Rotor Measurement and Assembly Platforms
iMAP
Rotary Precision Instruments UK Ltd
Improve productivity and achieve higher levels of quality by reducing inspection times and the need for costly teardowns due to inefficient rotor assembly. iMAP is the definitive system for productivity improvement in turbine rotor assembly for large volume and heavy loads such as aircraft engines and gas turbines.
-
product
XCITE 1200T Torsional Series
The Xcite 1200T Continuous Torsional Exciters provide high inertial torque in the frequency ranges required to excite steam turbine rotors, deisel engine crankshafts, and ship power drive trains. The speed range of up to 3600 RPM for the 1200T-9 and 7500 RPM for the 1200T-10 system is ideal for testing a broad range of rotating power generation equipment.
-
product
Integrated Turbine Rotor Measurement and Assembly Platforms
GeoSpin
Rotary Precision Instruments UK Ltd
Improve productivity and achieve higher levels of quality by reducing inspection times and the need for costly teardowns due to inefficient rotor assembly.GeoSpin has been specifically developed for the measurement and assembly of smaller gas turbine rotors for the aerospace and power generation industries reducing the rate of teardowns by 95%.
-
product
Test Fixture with API
TA-14VG
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
