Plugs
A male connector.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Bus Analyzer / Exerciser
VME850P2
-
The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.
-
Product
Matrix Switch Cards
1260-145 Series
Switch Card
These quickly and easily plug into the front of Astronics 1260-100 and 1260-101 Adapt-a-Switch™ carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
-
Product
Electronic Compact Pressure Switch (Pallect Pressure Switch)
PPE
-
mm.A compact trimmer setting type, three types of piping connections (R1/8, Φ6 plug, Φ6 one-touch fitting) and a dustproof/waterproof structure allow for flexible use.
-
Product
COLOCOIL® AM Isocoupler
-
LBA’s modular approach allows the operator to start with one CoLoCoil®, and build out to 6, 9, or more – supporting 50 or more antennas! Practically "plug and play", expansions are fast, minimize AM station impact, and maintain full grounding and lightning protection!
-
Product
PXI/PXIe Power Relay Module, 32xSPDT, 5 Amp, 50-Pin SGMC Connectors, With Interlock
42-158-001-HI
Relay
The 40/42-158-001-HI is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
Acute 2GHz, 34 Channel, TravelLogic Series Protocol & Logic Analyzer With 8Gb Memory
Acute TL4234B
-
The TravelLogic Series of Protocol & Logic Analyzers are small enough to fit into your shirt pocket, yet are truly sophisticated logic analyzers, capable of 2 GHz timing analysis, or 200 MHz state analysis, with up to 8 Gb total stackable memory for the 34 channels. They plug into a PC or Laptop USB port making them ideal for the field service technician or engineer, hopping from PC to PC, or taking with them for diagnosis on the road. Also remember that with USB, no additional power supply is needed.
-
Product
600-Watt DC/DC Converter, 6U VME/cPCI
55U91-01
DC Converter
NAI’s 55U91-01 is a 600 Watt DC/DC Converter that plugs directly into two card slots in a standard 6U VME chassis. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts +28 VDC input, provides up to 9 outputs at up to 614 Watts, and addresses the power supply needs of both VME and cPCI systems.
-
Product
EPON OLT ( Optical Line Termination )
OLT-1408
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OLT-1408's Optical Line Terminal (OLT) adopts GiGA Ethernet Passive Optical Network (EPON) technology. It is a compact chassis with L2/L3 GiGA switching and routing function. All the functional components are modularized design and it supports hot-plugging with plugging and playing. 1~4 pieces of GiGA optical port or electrical port are optional in the uplink port, which provides a direct optical interface for the Ethernet/IP network core. 1~8 pieces of EPON optical port are optional in the down link port. Through a passive optical Network (PON), an optical Network unit link (ONU),it can provide final transmission with bandwidth up to 1Gbps for the user.
-
Product
Diesel Tester Adaptor for Ford 6.0L
35650
-
Has 14mm-1.25 threads for testing at glow plug port. Applications include: Ford/Navistar Power Stroke 6.0L & 6.4L engines found on F-250 through F-550 trucks and International VT 365.
-
Product
Detector, Metal, Power, Stud
72-6792
-
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
Product
AC Power Supply
FC5003
-
Behlman’s FC5003 is a ruggedly built, COTS frequency converter designed to convert 120/208 VAC, 3-phase, 60 Hz, ground power to 115/200 VAC, 3-phase, 400 Hz, aircraft power. The FC5003 is in a rugged 6U (10.5”H) 19 inch rack mount chassis with an input line cord with plug and an output receptacle.
-
Product
High Current Probes (Plug Connectors) HCE08FB52S28E260
1052667
-
The High Current Probes (Plug Connectors) HCE08FB52S28E260 represent a premium choice for demanding electrical applications where reliability and durability are paramount. Designed to support continuous currents of up to 200A and featuring a robust construction capable of withstanding temperatures from -45°C to +200°C, these probes are perfect for high-load environments. They boast a basic contact probe design with an innovative spring mechanism that allows for a nominal travel of 4mm and a maximum travel of 5mm, ensuring excellent connection quality even under rigorous conditions.
-
Product
3-48V Auto Tester
1960A
-
Peaceful Thriving Enterprise Co Ltd
Check on 3-48V systems. Especially suitable for the control of electrical and electronic parts of motor vehicles, for the fault finding on components. The tester is connected with a banana plug adapter, including a testing probe and an alligator clip.
-
Product
PXI 10A Power MUX, 1-Bank, 16-Channel
40-661-103
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
Temperature Data Loggers
-
The Track-It™ Temperature Data Logger is a battery powered stand alone compact data logger that records up to 64,000 samples of temperature data. The unit is easily configured using the included Track-It™ Software. Simply plug the logger into an open USB port on your PC and the software automatically identifies the logger. Configure the unit to start and stop recording at a predetermined time and date or only when an alarm condition is sensed. The sample storage rate can be set from 1 sample every 2 seconds to 1 sample every 24 hours.
-
Product
Long Test Block (LTB)
-
The SecuControl LTB is a robust, finger-safe test block engineered for IEC substations. Paired with keyed STP test plugs and built-in CT shorting, the LTB provides make-before-break operation and patented sequential opening (trip → current → voltage) so relays can be isolated and tested without risk of open CTs or nuisance trips. Its extended rear access (long rear end) brings relay connections closer to the block for neater, more efficient cabling and flush panel integration.
-
Product
Network & Cable Testers
-
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
Product
50Ω uWave SMA 2.92 Cable Assembly, 40GHz, 1m
40-977-544-1m
RF Cable Assembly
50 Ohm uWave SMA 2.92 Plug to uWave SMA 2.92 Plug Cable Assy, 1m Long.
-
Product
NI 9980 10-Pos Spring Terminal (qty 10)
197991-01
-
10-Pin, Male COMBICON to 10-Pin, Female Spring Terminal Block Plug - The NI-9980 consists of a bag of 10 spring terminal plugs for any 10-position C Series module. These terminal plugs provide direct connectivity to the module. All C Series modules ship with the required connectors, so you can purchase the NI-9980 to add spring terminal connectivity, reduce wiring on multiple devices, or use for spare replacements.
-
Product
High Current Probes (Plug Connectors) HCF76289B218080570G300
1023603
-
The High Current Probes (Plug Connectors) HCF76289B218080570G300 are engineered to deliver exceptional performance and reliability in various electrical applications. With a design that features a basic contact probe configuration, these connectors exhibit a pitch of 4.00 mm, making them versatile for both space-constrained setups and standard configurations. Built to operate within a temperature range of -45°C to +200°C, these probes ensure durability across diverse environmental conditions, catering to the needs of professionals in demanding fields.
-
Product
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36" to 9-Pin DIN, 3 BNC Plugs & 2 SMB Plugs
540096010211
Cable Assembly
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36" to 9-Pin DIN, 3 BNC Plugs & 2 SMB Plugs
-
Product
Circuit Breaker Identifiers
191 CBI
-
Standard Electric Works Co., Ltd
● 191 CBI is an easy tool to find the circuit breaker or fuse supplying electrical power to an outlet or lighting fixture. Just plug the transmitter into the outlet.● Use the receiver to scan the circuit breaker panel box. An audible tone will be clearly heard when the right circuit breaker is scanned.● The plug of transmitter is changeable. The plug of transmitter could be changed for customers' requirement from different countries.
-
Product
Thermocouple (J-Type) And Temperature Probe Adapter
U1185A
Temperature Probe Adapter
The U1185A consists of a thermocouple bead (J-type) and a mini connector to dual banana plugs.
-
Product
Mini 4 Block Desktop Receiver
VGR4
Receiver
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250VAC/5Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Cable Assembly, Receiver, Mini Power/TriPaddle, 36", 7-Pin DIN and 4 Banana Plugs
540078010211
Cable Assembly
Cable Assembly, Receiver, Mini Power/TriPaddle, 36", 7-Pin DIN and 4 Banana Plugs.
-
Product
Switching Pedals
-
Are made specifically for effects pedals. In essence, they let you manage your pedalboard more efficiently, but offer far more than that. With several inputs (or "loops"), you can plug a few or indeed all of your pedals into a switcher.
-
Product
USB-TC01, 1-Channel Temperature Input Device
781314-02
Temperature Input Module
The USB‑TC01 is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take … temperature measurements with your PC. You can connect the USB‑TC01 to any USB port to use your PC as a display and monitor data in real time. The USB‑TC01 is compatible with J, K, R, S, T, N, E, and B thermocouples.
-
Product
Noid Lights, IAC Test Lights & Ignition Spark Tester Kit
36330
-
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
Product
SMB Connectors
-
Pasternack SMB connector category has dozens of part numbers, most are RoHS and REACH compliant. SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB connectors are built to precise microwave and RF industry specifications. Connectors in the SMB series are manufactured in jack or plug gender with 50 Ohm impedance. SMB connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this SMB connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
