Filter Results By:
Products
Applications
Manufacturers
AMC
Advanced Mezzanine Card
-
product
Core I7 Processor AMC, 10/40GbE
AMC727
The AMC727 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® next generation CoreTM i7 Processor (Haswell) with QM87PCH.
-
product
QorIQ P40x0 Processor AMC, SRIO
AMC719
The AMC719 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P4040 and P4080. The module follows the AMC.4 and AMC.2 specifications and the SRIO runs as dual x4. The module has options for up to 16GBytes of DDR3 memory with ECC.
-
product
36x36 Cross Bar Switch (CBS)
AMC241
The AMC241 is an AMC form factor with a 36x36 CBS which allows any of the 20 lanes from the backplane to be routed to the front. Since the CBS is agnostic to the protocol, any protocol such as PCIe, SRIO, 40GbE, 10GbE, GbE, Aurora, etc. could be routed between the backplane and the front panel.
-
product
PPC8315 Processor AMC W/ 2.5” SATA Drive
AMC715
The AMC715 is a Processor AMC (PrAMC) with an on board 2.5" SATA hard disk drive in a single-module, mid-size AdvancedMCTM (AMC) form factor based on the AMC.1, AMC.2 and the AMC.3 specifications. The module is ideal to be used for data flow management within a chassis. The AMC715 provides a low cost solution with an integrated high capacity disk. With a storage capacity of over 320 GB and data transfer rates of 150 Mbyte/s the AMC715 is the ideal AdvancedMCTM smart storage. The PCIe interface is configurable as Host or Agent mode. The module has 512 MB of DDR2 memory on board.
-
product
MTCA.4 Power Supply
To match the requirements of the next generation of “carrier grade” communication equipment the PCI Industrial Computer Manufacturers Group PICMG created in 2002 a new standard AdvancedTCA / ATCA. The ATCA crate backplanes are based mainly on 48V industrial power supplies. From this form factor evolve the Advanced Mezzanine Module carrier card AMC form factors defined in AMC.3 in types of single or double width.
-
product
QorIQ P204x Processor AMC
AMC711
The AMC711 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P2040 or P2041. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as dual x4 (ports 4-7 and 8-11). The P2041 has option to have ports 8-11 as XAUI (10GbE). The AMC711 has up to 8GBytes of DDR-III memory with ECC.
-
product
Intel® Xeon® Processor E-2176M AMC, PCIe Gen3
AMC760
The AMC760 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E-2176M (Coffee Lake) with CM246 PCH. The processor base frequency is 2.7 GHz with max turbo frequency of 4.4 GHz. The module follows AMC.1, AMC.2 and AMC.3 specifications.
-
product
Intel Xeon D-15xx Processor, AMC
AMC763
The AMC763 is a Processor AMC in a single module, mid-size, based on the Intel® 5th generation Xeon 4-core, 8-core or 16-core Processors (Broadwell). The efficient SoC design has low power consumption and integrated PCH technology. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
product
FPGA/FMC Carriers
Our AMC FPGA modules feature Altera Stratix IV, Altera Stratix V, Xilinx Virtex-5, Xilinx Virtex-6, Xilinx Zynq, Xilinx Artix, Xilinx Virtex-7 and Xilinx Kintex-7 FPGAs. We also offer a range of carriers that can accommodate standard FMCs featuring FPGAs from Altera and Xilinx, including the new Xilinx UltraScale family.
-
product
QorIQ P2020 Processor AMC
AMC717
The AMC717 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P2020. The module follows the AMC.1, AMC.2 and the AMC.4 specifications. The module is ideal for data flow management within a chassis. The PCIe/SRIO interface is configurable as Host or Agent mode. The PCIe option runs as x4 while the SRIO can run as x4 or dual x1. The module has option for up to 4GBytes of DDR3 memory with ECC. It provides Dual GbE to the rear per AMC.2 specification and a single GbE to the front.
-
product
Xeon D-15xx SoC Processor AMC
AMC754
The AMC754 is a Processor AMC in a single module, mid-size, based on the Intel® 5th generation Xeon 4-core, 8-core or 16-core Processors (Broadwell). The efficient SoC design has low power consumption and integrated PCH technology. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
product
QorIQ P5040 Processor AMC, PCIe
AMC704
The AMC704 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP P5040 (quad core) processors. The unit provides dual x4 PCIe on Ports 4-7 and 8-11 per AMC.1 and the PCIe interface can be configured in Host or Agent mode.
-
product
Xeon E3-1125 Processor AMC, Dual SRIO
AMC722
The AMC722 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMCTM (AMC) form factor based on the Intel® Xeon™ Processor with an 8900 Series PCH.
-
product
2 or 4 channel BC/RT/MT FMC Module.
NES-FMC1553-4
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMC’s to be supported on a wide range of existing form factor including but not limited to: PCle, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMC’s can be fitted on a 6U VPX carrier.
-
product
Processor AMC Based On QorIQ T4241, PCIe
AMC703
The AMC703 is a Processor AMC (PrAMC) based on the Freescale QorIQ T4241 in a single-module, mid-size AdvancedMCTM (AMC) form factor based on AMC.1, AMC.2 and AMC.3 specifications.
-
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
FMC Module
FMC1831
Sundance Multiprocessor Technology Ltd.
The FMC1831 is an FMC module designed to be compatible with AMC, VPX, PCI, PCIe, CompactPCI and PC/104 carriers. The module has two dual channel AD9361 transceivers with a maximum sampling frequency of 122.8 MHz over a bandwidth of 200 KHz to 56 MHz. A reference clock can be either externally supplied or be generated from an internal PLL. All input and output signals are connected via SSMC connectors for secure connectivity and signal integrity.
-
product
Advanced Mezzanine Card (AMC) Module
AMC SyncClock32
The AMC-SyncClock32 from Brandywine Communications is an Advanced Mezzanine Card (AMC) module. Precision time is provided to the host computer with zero latency. The onboard microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs handled by the AMC in its standard configuration are IRIG’s A, B/IEEE1344, and NASA 36. Alternatively, the clock in the AMC can be set using commands from host computer and free run using its on-board oscillator as the time base.
-
product
Xeon E3-1125 Processor AMC, XAUI
AMC721
The AMC721 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMCTM (AMC) form factor based on the Intel® Xeon™ Processor with an 8900 Series PCH.
-
product
Cavium CN63xx Packet Processor AMC
AMC730
The AMC730 is a a 10-Gigabit Ethernet (10GbE) AdvancedMCTM(AMC) module which includes an on-board line rate multi-core packet processor based on Cavium CN63XX CPU. VadaTech offers this product in a mid size (full size optional) form factor with the AMC.1, AMC.2 and AMC.4 specifications. The AMC730 is based around the Cavium OCTEON CN63xx processor which has been specifically designed to intelligently process Ethernet packets at line rate.The processor can be loaded via the PCIe/SRIO interface or via an optional flash memory. The number of processor cores, speed grade, and amount of DDR3 memory is customizable based on customer needs. The module has 2GB of HFA for pattern matching for deep packet inspection, etc. The SDK for the processor as well as additional software stacks are available from Cavium or third party.
-
product
QorIQ P40x0 Processor AMC, PCIe Gen 2
AMC718
The AMC718 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P4040 and P4080. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as x8 or dual x4. The module has option for up to 16GBytes of DDR3 memory with ECC.
-
product
Automated Monitoring of Airborne Molecular Contamination
AMC-Monitor T-1000
The all-in-one analyzer for FOUP, fab and clean-room environment AMC monitoring in the semiconductor industry. The AMC-Monitor is a modular and flexible platform for airborne molecular contaminations (AMC) monitoring in semiconductor applications such as: FOUP analysis with a focus on VOC and condensables incl. full integration with Pfeiffer Vacuum APA 302 pod analyzer. Clean-room monitoring in fabrication plants.
-
product
Graphics
Designed to meet the high performance and real-world graphics needs of military, industrial and telecom equipment manufacturers, VadaTech’s AdvancedMC (AMC) graphics modules feature specialized processors from ATI or Silicon Motion and offer DVI, VGA and HDMI options. Our portfolio ranges from very simple and cost-effective graphic interface modules to one of the fastest and most advanced, high-performance 2D and 3D graphics processors available for the AMC embedded market, as well as video driver modules.
-
product
Digital and Serial I/O
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
product
5 Port PCI Express
PEX 8508
The ExpressLane™ PEX 8508 8-lane, 5-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device enables users to add low cost, scalable high bandwidth switching, both fan-in/out and peer-to-peer, to a wide variety of applications including office automation, network interface adapters, docking stations, AMC cards, and processor isolation for servers, storage, and communications.
-
product
QorIQ P5010/5020 Processor AMC, PCIe
AMC713
The AMC713 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP P5010 (single core) or P5020 (dual core) processors. The unit provides dual x4 PCIe on Ports 4-7 and 8-11 per AMC.1 and the PCIe interface can be configured in Host or Agent mode.
-
product
Tilera GX72 Processor, 72 Core, Mid-size, AMC
AMC741
The AMC741 is ideal for packet filtering, intelligent networking, multimedia, video transcoding, cloud and other applications. The device includes 72 identical processor cores (tiles) interconnected with Tilera’s iMesh™ on-chip network.
-
product
Rugged 3rd Gen MicroTCA Carrier Hub (MCH), 40GbE/PCIe Gen 3
UTC042
The VadaTech UTC042 is a rugged version of the UTC004 (the most feature-rich MCH on the market). The front I/O Dual Ethernet Ports have changed from 10G copper to the 1 Gb copper, all other I/Os match the UTC004. The management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 AMCs within the chassis. It also manages the optional PCIe Gen3, SRIO Gen2, 40GbE/10GbE or Crossbar Fat Pipe switches as well as the standard GbE with 1GbE uplink Base Channel switch.
-
product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
