Discrete Semiconductor Testers
check connected individual semiconductor components.
-
-
Product
Network & Cable Testers
-
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
Product
PON Tester
-
Shanghai Grandway Telecom Tech. Co., Ltd
In order to effectively manage the user resources of FTTH, we have developed new generation products FOH-8PRO and FOH-100 to help operators complete the user resource management.
-
Product
Isolation Tester UIP
-
The devices of the UIP (Union Isolations Prüfer) isolation tester series are used to test the pore-free condition of corrosion protection coatings of pipes, vessels or plant system parts. The battery-powered device generates test voltages between 5 kV and 30 kV, which are applied to the grounded test object via test electrodes. The location of a defect is signalized by a spark-over with an additional audible warning.
-
Product
Bonding Tester
PTR1102
-
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
Product
Axis Play Tester
PMS 3.5 | VP 225012
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axis play tester PMS 3.5 is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the PMS 3.5 easy to use.
-
Product
Solderability Tester
ZHX-35
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
Product
Insulation Tester
Calibrated 1kV Megohmmeter
-
*Calculations (automatic)*Potential Index and Dielectric Absorption Ratios*Tests Continuity, Resistance and Frequency Measurements*Programmable Alarms*Insulation Test, Resistance, Continuity*Hazardous Voltage Alert (Icon) if voltage is >70 volts 5.) On Board Timer, +1/- 1 sec.
-
Product
Phase And Continuity Tester
4100
-
Peaceful Thriving Enterprise Co Ltd
There are two function of this tester. One is to test the continuity and the other one is to test the phase of three-phase system. The operation is easy, the indication is clear with LED indication. There is a loud buzzer to remind you the continuity. The illumination is very helpful in the dark environment.
-
Product
Film Impact Tester
DRK136A
-
Shandong Drick Instruments Co., Ltd.
DRK136A Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.
-
Product
Yarn Count Tester
TY361
-
TESTEX Testing Equipment Systems Ltd.
Yarn Count Tester, automatically calculates count systems used for sliver, roving and yarn, and can also be used for fabric yield. Yarn Count Tester consists of an accurate electronic balance and built-in calculating program.
-
Product
Cable Tester
LX-560A
-
Shenzhen Lian Xin Technology Co., Ltd.
Cable/Harness Tester (low-pressure type) features its capability of testing the components inside the wire, the test speed more than double faster than that of the traditional wire testers, and the provision of such functions as unilateral, turn-on resistance editing, and spot metering color editing.
-
Product
Motor Tester and Analyzer
ITIG
-
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
Product
DMX Tester
DXT1
-
The new DMX Tester from NuDelta Digital is a feature-packed test tool you won't want to leave home without. It can send any level to any DMX address with simple commands similar to those found on the world's most popular lighting consoles. It can test for valid DMX signal and show you the level at any address. It can test continuity on all five pins of a standard DMX cable and indicate which pins are not connected or cross-wired. Runs for hours on a 9 volt battery (included).
-
Product
Transient Over-voltages Tester
SUG335
-
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
Product
Partial Discharge Tester
19501-K/19500
-
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
Product
Continuity Tester, LED
26330
-
If the bulb lights up, continuity exists. If the bulb fails to light, the circuit is open. Not for use on live circuits, but incidental contact with 12V supply will not burn out LED bulb.
-
Product
pH Tester
148
-
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, ITA
410114298
Protective Cover
Protective Cover, 9050, VXI and Discrete Wiring, ITA.
-
Product
HID Ballast Tester
WT2000-HID
-
• Input Parameters Measurement: 1) Test voltage, current, power, power factor, power line frequency, total harmonic and 0~50 harmonic 2) Range of voltage and current basic wave frequency: 45Hz~65Hz 3) Range of narrow frequency: 45Hz~5kHz 4) Range of wide frequency: 45Hz~1MHz
-
Product
EOL Tester
-
Sterner Automation would like to introduce its new end of line (EOL) tester platform. Sterner Automation has been a supplier of calibration and test equipment to the automotive industry for over a decade and is now offering a standard hardware EOL platform that is configurable with a variety of software modules for seating plant applications.
-
Product
Zipper Tester
-
TESTEX Testing Equipment Systems Ltd.
Zipper Tester, to determine the resistance to reciprocation of zipper (slide fastener), the test specimen is subjected to a specified number of cyclic operations whilst under lateral and longitudinal tension. Zipper Tester complies with BS 3084, CNS -1083, QB/T2171-1995, etc. Please contact us for more about information about pull test procedure.
-
Product
Hardness Testers
-
The QATM hardness tester portfolio covers all standard test methods, such as Vickers, Brinell, Knoop & Rockwell, as well as a wide test load range. The entire hardness tester range is characterized by technological innovation, precise measuring instruments and maximum comfort due to automation and advanced interfaces.
-
Product
LAN Cable Tester Plus
PK-3456 Spy Splitpair
-
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
Product
Wire Abrasion Tester
SG-D03DG
-
This machine is mainly based on UL1581 / UL83 standard abrasion test wire and cable testing requirements .
-
Product
Radio Vector Tester
-
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
Product
Diesel Tester for Mercedes Benz-Vehicles
34780
-
Has piggy-back 12mm-1.25 & 18mm-1.50 threads for testing at glow plug port. Applications: 12mm is for Model 300 & 300 Turbo Diesel from 1978 and the 250 & 350 Turbo models. 18mm is for all regular Mercedes Benz engines & Model 300 prior to 1978.
-
Product
Polarization Tester
-
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
