-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Proving Unit
PRV240
-
The Fluke PRV240 provides a safe method to verify that your electrical test tool is operating properly before and after you conduct any live tests. The concept of “Test Before Touch” (TBT) involves testing your meter against a known live source before and after the actual measurement.
-
Product
Measurement And Control
-
Amplicon supplies Measurement and Control products for every type of application, from high-end Test & Measurement to a simple digital panel meter installation. We have products that can monitor, display and log high and low speed signals.
-
Product
Measurement Sensors
-
Atlas Material Testing Solutions
Atlas offers various sensors measuring irradiance and temperature to operate and to calibrate your weathering instruments.
-
Product
Source Code Review
-
Source code review, also known as Security Code Review is the process of auditing the source code for an application to verify that the proper security controls are present, that they work as intended, and that they have been invoked in all the right places. Code review is a way of ensuring that the application has been developed to be “self-defending” in its given environment.
-
Product
Hall Effect Measurement system
HMS-5300
-
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
Product
Power And Bus Protection Units
-
Silver Engineering Inc. offers several Bus Protection Units designed to protect the power input to a spacecraft or payload during integration and test activates. The BPU’s monitor for over/under voltage and over current and disconnects power in the event of a fault condition.
-
Product
Three-Phase AC Power Sources
AC6900 Series
-
Keysight’s AC6900 Series AC power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument. You can easily produce DC power, either alone or as a DC offset to an AC waveform, in a compact form factor.
-
Product
PLTS N-Port Measurement And Analysis
N19307B
-
PLTS N19307B extends the N19301B base product to perform N-port (greater than 4 ports) measurements and analysis
-
Product
Temperature Measuring Board
W16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Temperature Measuring Board conform to IEC60335-1:2004 and GB4706.1-2005 can be used to the temperature test of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.
-
Product
Sund Source
Qohm
-
The extreme low weight of 3.5 kg and small dimensions allow highly efficient measurements, saving time in transportation and test-set-up. This set prevents heavy lifting work and allows flexibility in positioning during tests, because also the tripod, power amplifier, and soft-bag are light weight.
-
Product
Angular Position Measurement Kit
55290A
Accessory Kit
The Keysight 55290A Angular Position Measurement Kit automatically calibrates rotational axes in turning and machining centers. It can perform calibrations on full, partial or multiple rotations, improves angular positioning accuracy, and allows the documentation of machine tool capability.
-
Product
Remote Plasma Sources
-
Equip your manufacturing and abatement processes with high functionality and exceptional reliability. Customize your chemistry. Expand your operating range. Deliver higher process rates. Advanced Energy’s remote plasma sources offer sophisticated options in streamlined designs.
-
Product
Multi Channel LED Light Source
LE7
-
Image Engineering GmbH & Co. KG
The iQ-LED is the latest development of Image Engineering. It is a multi channel LED light source that provides the possibility to generate the spectral characteristics of nearly every required light source in just one device. With its 22 different software controlled LED channels it is possible to generate a spectral match of standard light sources such as, D50, D55, D65, A, B, C etc. with very high accuracy.
-
Product
Environmental Conditioning Units
-
CSZ's environmental conditioning units are designed to create temperature and humidity controlled climates inside a digital printing press. This controlled environment was required to maintain consistent conditioning of printing press components in order to achieve high quality printed material.
-
Product
Multi-Function Test & Measurement System
-
Optoplex’s Multifunction Test and Measurement System (TM100 Series) is designed to provide a flexible and cost effective optical test and measurement solution, particularly for manufacturing lines. The mainframe can be mounted in 19” rack or stationed on desk-top for ease of use. There are many selections of the pluggable modules, from tunable laser, optical spectrum analyzer, EDFA, power meter, ASE light source, optical tunable filter, optical performance monitor, …, etc.
-
Product
Temperature Measurement Interments
-
Most everyone wants to know the temperature on a daily basis, so we rely on accurate thermometers to give us this information. Testo manufactures a fully comprehensive offering of temperature solutions employing different senory technologies among a full assortment of measuring devices, all supported with a great probe selection to fit nearly any application.
-
Product
SLED Source Driver
S-108
-
SLED Source & Driver slot module of FOTS system is an efficient module that can drive a stable high power broadband source and modulate a high power SLED to output a high bit rate optical signal. As a high power broadband SLED source, this module can drive the maximum output power of more than 14 dBm and has a stable wideband source characteristics of >90nm@-20dBm/nm. As a high current (400mA) modulation technique, it shows a high power and high bit rate digital signal of > 155 Mbps with > 13 dBm peak power.
-
Product
VCSEL Light Source
-
ams supplies LiDAR systems with specific light sources, called VCSEL (Vertical Cavity Surface Emitting Laser). These VCSELs offer specific advantages over other types of light sources as for instance Edge Emitter Lasers:
-
Product
AC Power Sources
-
Test basic AC power with confidence using the most stable, reliable AC power sources More effectively simulate and analyze high-performance AC environments with built-in measurement capabilities Lower your cost of ownership with global support and the longest standard warranty in the industry
-
Product
Vector And Scalar Mixer/Converter Measurements
S96083B
-
S96083A provides fully calibrated conversion gain/loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers
-
Product
Sag Measurement Instrument
DUMES
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Mounting on the lattice mast*Adjustable angle elements with 5/8‘‘ tapped hole*Tubular level for levelling instrument*Three axis precision scope with wide angle eyepiece*Magnification 30-x*Made in Germany
-
Product
Rotary Torque Measurement System
-
Honeywell Industrial Automation
Honeywell's analogy telemetry rotary torque systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements.
-
Product
Broadband Xe Light Source
PowerArc
-
75W Xe Ozone free light source for UV-Visible-NIR applicationsThe PowerArc™ is a complete, integrated light source that includes power supply, starter, high efficiency collection optics and lamp housing in one compact package.
-
Product
R*evolution® Remote Plasma Source
-
The innovative R*evolution® Remote Plasma Source combines field-proven, low-field toroidal plasma technology with an actively cooled plasma chamber made of high purity quartz, significantly reducing oxygen, hydrogen and nitrogen atomic gas loss through wall recombination. Self-contained and compact, R*evolution delivers up to 10 slm of oxygen radicals from a 6kW power supply with true power accuracy of <1% resulting in a high density, extremely clean radical source for photoresist strip and an optimal clean rate greater than 12 microns/min-1. R*evolution can be used for other surface preparation applications.
-
Product
Broadband Calibrated Noise Sources
-
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
Product
Noise Sources
NC1128A
-
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
Product
Front Panels for Plug-In-Units | IEC
-
Front panels for plug-in-units according to IEC | with or without EMC protection | aluminum 2.5 mm | clear anodised
-
Product
Safety Control Unit
Epec SC52
-
SC52 offers a flexible solution for software-based safety function implementation. Together with the SC52 controller, Epec offers a set of pre-certified PLCopen application libraries in order to reduce customer’s safety related software development effort.
-
Product
Inertial Measurement Units
IMU
-
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
