Programmable DC Electronic Loads
Vary load current programmaticlly.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
DC Bench Power
XPH Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPH Series provides 175 to 420 watts of DC power. The XPH is a compact, high performance low cost power supply suited for benchtop applications. The Sorensen XPH Series uses combined switch–mode pre–regulation with linear post-regulation to provide performance comparable with an all linear design. The XPH features excellent line and load regulation with low noise and good transient response. The XPH Series is available in a single, dual and triple output for benchtop use.
-
Product
Auger Electron Spectroscopy (AES)
-
Rocky Mountain Laboratories, Inc.
Auger Analysis, Auger Electron Spectroscopy (AES or Auger) is a chemical surface analysis method. AES measures the chemical composition of the outermost 100 Å of a sample. Measurements can be made at greater depths by ion sputter etching to remove surface layers.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-011
Programmable Resistor Module
The 40-254-011 (PXI) and 42-254-011 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 61Ω with 0.25Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Programmable Power Modules
Series MST
-
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
Product
Synchro to DC Converters
DC Converter
Computer Conversions Corporation
This unique series of Synchro to DC Converters makes use of advanced digital circuitry techniques to accomplish high speed conversion with extreme accuracy. Transformer isolation as well as balanced line-to-line input impedance is provided for superior and trouble-free system performance, regardless of the input synchro used.
-
Product
Precision Programmable DC Voltage Calibrator
2701C
-
Designed for critical calibration lab requirements, this 4th generation contemporary 2701C design is lightweight, rugged, and at home on the production line or the engineer’s workstation.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-034
Programmable Resistor Module
The 40-297A-034 (PXI) and the 42-297A-034 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBO SERIES
-
The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.
-
Product
Programmer Memories VP-598
-
Support more than 21 637+ memories . We are official distributor of Wellon products in Poland. Our customers receive 3 years warranty and 72h support.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 102kΩ
40-251-134
Programmable Resistor Module
The 40-251-134 is a programmable resistor module with 2 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 4Ω to 2.97MΩ
40-298-151
Programmable Resistor Module
The 40-298-151 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 2.97MΩ with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
AC Load Bank (Resistive)
K-1000 Resisitive
-
Kongter Test & Measurement Co., Limited
The kW of a resistive load bank is “real” power in electrical terms. When a resistive AC load bank is used to test an engine generator set the engine will produce its full horsepower rating, dissipate engine exhaust gases, and produce thermal energy into the engine cooling system. The resistive load bank in fact, will completely test the engine and its various systems.
-
Product
Cathodoluminescence Solutions for Electron Microscopy
CLUE Series
-
HORIBA Scientific's Cathodoluminescence Universal Extension enhances any SEM’s analytical capabilities while maintaining its original functionality. Since the sample is able to remain in the same spot, CLUE can easily be combined with other microscopy applications, such as EDS and EBIC.
-
Product
DC Power Supplies
-
Scientech Technologies Pvt. Ltd.
Power Supply is the most indispensable component of any electronic laboratory. A reliable, most accurate, fully specified, guaranteed and an efficient Power Supply Equipment are thus manufactured on a large scale by Scientech Technologies which has robust output protection and fault detection capabilities. DC Power Supplies with Different specifications of Voltage and Current are being manufactured for various Applications. The DC power supply converts the conventional 110 V or 220 V alternating voltage into continuous pulsating DC voltage (+3.3 V, +5 V, +12 V and -12V) used by various electronic components. A DC Power Supply also regulates the voltage to eliminate spikes and surges common in most electrical systems.
-
Product
Surge / DC Hi-Pot Consoles
HC Model
-
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
Product
DC Power Supply
-
The main products of DC Power Supply are divided into four categories: linear DC power supply, programmable DC power supply, switching DC power supply, and DC power supply, which are subdivided into single output/dual output /Four sets of memory dual output/ high voltage/high power/high resolution/four sets of memory dual output/dual range/customized specifications and other DC power supplies are available for you to choose and use the appropriate DC power supply to get the best results. Best noise performance and device protection.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-030-HI
Programmable Resistor Module
The 40-230-030-HI (PXI) and 42-230-030-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Scanning Electron Microscope
JSM-IT510
-
Scanning electron microscopes (SEMs) are indispensable tools not only for research but also for quality assurance and manufacturing sites.At those scenes, the same observation processes need to be performed repeatedly and there has been a need to improve the efficiency of the process.
-
Product
Current Logger0 to 25mA DC
TV-4804
-
The TV-4804 measures current from 0 to 25mA DC and can be connected to a variety of industry standard sensors enabling the logging of a wide range of process parameters.
-
Product
DC BIAS CURRENT UNIT
3265B SERIES
-
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
Product
DC Hipot Tester,
294
-
Our Model 294 is a simple-to-use DC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 294 DC Hipot Tester includes all the features you need to get the job done and move on. Make testing simple with common sense security settings. PLC Remote allows you to make DC Hipot Testing safer with Personal Protective Equipment (PPE).
-
Product
Portable DC Power Supply
PS 30-20
-
Laxtronics Instruments & Controls Pvt. Ltd
Input Voltage 220 V, 50 HZ, 1 PH.
-
Product
DC Block
-
DC block offering broadband performance used to protect equipement and components from DC voltages
-
Product
DC Hipot Tester
296
-
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
Product
DC Voltage/Current Generators
-
Pulse generation/measurement with basic accuracy of ±0.02% and the minimum pulse width of 50μs, maximum output of 6V/5A
-
Product
PXI Precision Resistor Module 4-Channel, 1.5 to 3.55k
40-297-123
Programmable Resistor Module
.This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
-
Product
Adapter & DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband. RF Lambda’s line of adapters are used to connect RF signals using different connector options.
-
Product
Programmable DC Power Supply
SPD1000X Series
-
SPD1000X Programmable Linear DC Power Supply has a 2.8 inch TFT-LCD display, features remote computer control capability, and real time wave display. This single output design is focused on delivering high performance and ease-of-use in a small package. The SPD1168 features a high precision programmable output capable of delivering up to 16 V/8 A,the SPD1305X features a high precision programmable output capable of delivering up to 30 V/5 A and also includes a 4-wire sense function for more accurate voltage sourcing, especially for long leads or high resistance connections. There are additional output short and overload protect functions to assist in production and development applications.
