Test Adapters
See Also: Interface Test Adapters
-
Product
PCI to PCI Express Adapter
SKU-011-01
-
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
Product
Test Capabilities
-
Eltek International Laboratories
ELTEK Labs has conducted more Electrical Insulation Systems (EIS) and Component Compatibility Testing (CCT) than all other laboratories worldwide combined. ELTEK Labs is proud to be a Third-Party Testing Laboratory for internationally recognized certifying bodies.
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
-
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
Product
SAR Testing
-
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
Product
Piezoelectric Testing
-
Radiant Technologies, Inc. specializes in the measurement of electrical and piezoelectric properties of non-linear materials. The Piezoelectric Task captures a sample's displacement as a function of voltage profile along with the sample's polarization response. An external displacement measurement instrument must be attached to a Radiant Precision Test System to make this measurement. All of the Radiant testers are equipped with a high-impedance voltage input to capture the output of a displacement sensor. Every Vision measurement task will collect data from that sensor input simultaneously with the measurement being executed. Radiant's test systems work easily with displacement sensors which include:
-
Product
Test Probe
-
Beijing KeHuan Century EMC Technology Co,.LTD
Is a physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
Test Stands
-
We develop modern and flexible test stands for research, development and production. In doing so we exclusively use our own in-house imc measurement hardware and software platform that has become established in the testing market worldwide. Our experienced “customer solutions team” is at your side during all phases of project development: from planning and construction through to configuration and implementation phases. We are also more than pleased to support you in modernizing and retrofitting existing installations and protecting your investment in the future.
-
Product
Factory Testing
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Efficient factory testing is vital in order to achieve the tightest tolerances, maximum repeatability, high precisi- on and quality in the manufacturing processes, as well as long production machine lifecycles. What‘s more, it helps to reduce manufacturing costs due to minimized replacements, retesting processes, and recalibrations. Online CatalogApplication Notes
-
Product
EMC Testing
-
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
Product
In-House Testing
-
Aerodyn’s state of the art test facility features vast capabilities for new product development and testing to meet our customers’ needs. By coupling our extensive design, fabrication, and instrumentation capabilities, along with our LabVIEW certified engineers, Aerodyn offer the utmost support to allow for very quick test setups and delivery of results.
-
Product
Fiber Adapter
I2C fiber adapter
-
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*Up to 350kHz*Up to 50m*No software or drivers required
-
Product
XMC-to-PCI Express (PCIe) Adapter
8613
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 4X (8613) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
Test Contactor
cDragon
-
cDragon™ Test Contactor pin’s thermal design supports fast temperature control response and stabilization for repeatable at temperature testing of devices in a handler environment.The homogenous MEMS elastomer-free multi-beam pin delivers long life and high wear resistance. By design the cDragon’s pin decouples insertion motion from the test-interface-board side of the pin. This eliminates test-interface-board pad wear.
-
Product
Passive XMC-to-PCI Express Adapter
5935
-
The Technobox, Inc. P/N 5935 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
EBIRST 78-pin D-type Coaxial Adapter - 37 SMBs
93-006-202
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Semiconductor Testing
-
The integrated PXI platform and the open interfacing provides extension capabilities for additional testing requirements like DUT specific resistors-networks or temperature sensors. The Test System comes with the ready-to-run GTSoftware package and allows easy programming of test sequences (GTbuilder) and fast execution in production/test mode (GTengine).
-
Product
Modular Testing
-
Modular testing requirements come in all shapes and sizes. It is therefore important that we are able to match your requirement with a suitable ATE System. At ATE Solutions, we have a range of modular test and test automation products to choose from, with a tester to suit every situation.
-
Product
Test Systems
-
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
Product
Test Programming
TestAssistant II
-
From a front-end graphical user interface to a back-end relational database, TestAssistant II organizes and maintains everything necessary for testing. Tester interfaces, wires, connectors, adapter cables, and other complex sub-assemblies are graphically represented.
-
Product
Noise Test
-
As experts in the acoustic industry, our company offers a wide range of noise monitoring equipment, including sound level meters, monitoring substations, and noise localization devices. We also provide customized solutions to meet specific scenarios and requirements for noise control.
-
-
Product
Test Fixtures-Assemblies
-
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
USB I2C Adapter
MS (Master & Slave)
-
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
Product
Test Probe
-
A physical device used to connect electronic test equipment to a specific point on a circuit or device under test.
-
Product
NI-6585B , 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
784060-01
Digital I/O Adapter
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
Test Port Adapter
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
PCIe adapter for PMC
PCIeBPMCX1
-
Now you can use your PMC with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. The PCIeBPMCX1 ( PCIe Bridge PMC 1 slot) adapter / carrier converter card provides the ability to install one PMC card into a standard PCIe (Express) 4 lane slot.
-
