Wind
See Also: Wind Tunnels, Anemometers, Wind Turbine, Wind Speed, Turbulence
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
Wind Tunnels
-
Omega's Wind Tunnels come in benchtop or floor standing models for any research, manufacturing, or quality control application. All Wind Tunnels are manufactured in The USA.
-
Product
Wind Turbine Performance Lidar
Wind Iris
-
The Wind Iris is based on Leosphere's leading WINDCUBE pulsedLidar technology, and is the first remote sensor dedicated to turbine-mounted measurements. It measures the horizontal wind speed and direction from 40m to 400m upwind of the turbine. Real time and average data can then be transferred automatically or stored in a data logger.
-
Product
Wind Sensors
FT742
-
The FT742 measures wind speeds up to 75 m/s. Its innovative design incorporates a series of “turbulators” which condition the air flow to deliver our highest levels of accuracy yet. Available in four mounting options, the Flat Front (FF) and Pipe Mount (PM) are typically used in wind turbine control and the Direct Mount (DM) in meteorological applications. The Surface Mount (SM) has been specifically designed for OEM integration and for use on UAVs/drones.
-
Product
Wind Turbine Lidar
ZephIR 300
-
ZephIR 300 measures wind characteristics onshore and on fixed or floating platforms offshore from just 10 metres (33 feet) up to 200 metres (656 feet) from installed position to inform wind regime and quality studies during the development and operation of wind farms onshore and offshore.
-
Product
Wind Power Solution
EVO ACCIONA
-
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Wind Tunnel Control System
WTCS
-
Wind tunnel facilities are important for the development of all kinds of transportation vehicles. In any kind of wind tunnel - aerodynamic, climatic or acoustic - users are interested in optimization of the valuable factor time for the performance of experiments and measurements. Aerodynamic properties exerting direct influence to fuel consumption have to be optimized.
-
Product
Pocket Wind Meter
Kestrel 3000
-
The Kestrel 3000 Pocket Weather Meter is the handheld weather-monitoring device that provides a wide range of functions, plus accurate relative humidity measurements. Before the Kestrel 3000 came along, the technology required to gather this information would require masses of equipment but not anymore. The Kestrel 3000 Weather Meter measures essential environmental parameters like temperature and wind speeds, and has added advantages for professionals that need access to humidity and heat stress readings.
-
Product
High-precision Surface Inspection for Wind Turbine Blades
waveCHECK™
-
8tree's waveCHECK is a handheld-portable 3D-inspection tool for inspecting wind turbine blades in manufacturing and operation. Its efficient detection of surface defects and instant visual feedback revolutionize surface inspection.It can detect wrinkles, steps, gaps, rain erosion and any other surface damage.
-
Product
Wind Profilers
-
Bristol Industrial & Research Associates Ltd
Biral provides Sodar systems for the 3-dimensional measurement of wind speed and direction in a vertical column extending hundreds of metres above the sensor. Sodar systems are used in applications such as wind energy site assessment, wind shear detection at airports, plume modelling and basic research.
-
-
Product
Wind Sensors
FT702
-
The current version of the FT702 is Version 22. Its strength and dependability have made it particularly popular for wind turbine control. It is used globally by the world's leading wind turbine manufacturers, as well as in a range of meteorology applications.
-
Product
Solid-State Wind & Meteorological Measurement System
AGIMET
-
Aeronautical & General Instruments Ltd.
AGIMET uses the latest proven solid-state meteorological sensor technology specially designed for the marine environment to provide accurate measurement of wind speed and direction, temperature, pressure, humidity and other local environmental parameters.
-
Product
Wind Power Solution
NXA SIEMENS
-
The NXA SIEMENS is custom-made with firmware and fixtures designed specifically for Siemens 2.3, 2.4, 2.6, 3.6, and 4.0. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Dual Mode Wind Turbine Performance Lidar
ZephIR DM
-
ZephIR DM is a Dual Mode variation of the successful 300 system. ZephIR DM measures wind characteristics in front of or behind a turbine from just 10 metres (33 feet) out to 300 metres (984 feet) situated inside the spinner or on top of the nacelle, during the operation of wind farms onshore and offshore (this is limited to 200m (656 feet) when in ground based vertical mode).
-
Product
Wind Power Solution
ECO SUZLON
-
The ECO SUZLON is custom-made with firmware and fixtures designed specifically for Suzlon turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Wind Tunnel Balances
-
To meet the increasing demands of a modern wind tunnel and the need for appropriate simulation, HORIBA has developed the rolling road and wheel spinning units for road simulation. To increase the wind tunnel efficiency, the HORIBA wind tunnel balances can be equipped with lifting platforms which enable vehicle modifications to be performed in a short time
-
Product
Distribution Transformer Tester
NDB-DOC-3™
-
The NDB-DOC-3™ is a test instrument designed for distribution networks transformers from 5kVA to 3MVA. It can determine the presence of short circuits or open circuits in the distribution transformer primary winding & also short circuits on the secondary winding.The NDB-DOC-3™ is designed to be operated without disconnecting the transformer’s secondary windings from their loads.
-
Product
All-in-One Weather Sensors
-
Basic weather sensors measure six parameters: wind speed and direction, precipitation, barometric pressure, temperature, and relative humidity. These compact, multi-function sensors have no moving parts.
-
Product
Winding Resistance Meter 50Amps, 3 Channels
WR50-13
-
Raytech Digital Winding Resistance meter WR50-13 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Transformer Ratio Meter
TRM 1000
-
AJIT Transformer Ratio Meters are the most modern turn's radio meters widely used to test the turn's ratio of high voltage windings, to low voltage windings, of Transformer. These meters are accurate, compact & light in weight.
-
Product
Handheld Turns Ratio & Winding Resistance Tester
TWR-H Series
-
Handheld TWR-H device is DV Power single-phase instrument designed for measuring transformer winding resistance and turns ratio.The instrument has two output DC sources for measuring transformer winding resistance. The first DC source can output up to 2 A DC and is used for injecting current to the transformer’s high voltage winding. The second DC source can output up to 10 A DC and is used for testing the transformer’s low voltage winding. This is especially useful when measuring winding resistance of distribution transformers. These transformers have large turns ratio and therefore a big difference between resistances of high voltage and low voltage windings. Upon the winding resistance test, it is also possible to demagnetize the transformer core. The demagnetization process is completely automatic and safe.Together with the turns ratio, the instrument also measures excitation current and phase shift. This enables detecting transformer core or winding turns failures which cannot be spotted by measuring turns ratio only. The instrument can output test voltage up to 40 V AC for this test, but it can also output a very low test voltage of 1 V AC which is necessary for turns ratio verification of the majority of current transformers.TWR-H is powered by an internal Li-Ion battery. Up to 100 tests can be performed with a fully charged battery.
-
Product
Vigilant Aircraft Hygrometer
137
-
The Edgetech Instruments Model 137 Vigilant Aircraft Hygrometer is a rugged, shock mounted military qualified instrument used for the primary measurement of dew point in flight or in installations with existing flow, such as wind tunnels.It features a miniature remote dew point sensor employing a platinum resistance thermometer, and has 15 feet of interconnecting cable to the control unit. Precision calibration units for the linear analog outputs are included.
-
Product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
-
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
Product
Digital Surge Tester
5KV & 6KV
-
The Digital Surge Tester is designed specifically to test the coils and windings of Low range AC Rotating machines ranging up to 660 V. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
Product
Coil Tester
-
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
Product
Signature Model High Frequency Surge Testers
S
-
Bench size performance & durability with PJ's exclusive/unique High Frequency Technology capable of testing the integrity of any turn to turn insulation, including low inductance windings. These Digital Surge Testers come standard with a rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope.
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
Product
TRANSFORMER WINDING RESISTANCE METER
-
International Biological Laboratories
This Test set is suitable to measure winding resistance of transformers, single or 3-phase, star or delta connected upto several MVA.Two independent displays read the resistance of both primary & secondary windings simultaneously. However, primary or secondary winding can also be measured separately.
-
Product
Tap Changer Analyzers & Winding Ohmmeters
-
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
