Instrumentation Amplifiers
A type of operational amplifier used when a circuit needs accuracy and stability.
See Also: Instrumentation, Amplifiers, Instruments
-
Product
Laboratory Instruments
-
Communicating 60,000-count TRMS benchtop multimeter for a broad range of applications in electronics and electrical engineering (1,000 V Cat. III) .
-
Product
Low Noise Amplifier
DLNA8-40-50-2582
-
Low Noise Amplifier, Frequency 40~50GHz, Gain 38dB, Noise figure 3dB, P-1dB 13dBm, 1.85mm-Female Removable
-
Product
Countermeasures Amplifier
CMA-100
-
CMA-100 Countermeasures Amplifier is a high gain audio amplifier used to detect and identify certain types of surveillance devices attached to building wiring such as telephone wiring, LAN and server systems, AC power, and alarm wire. The CMA-100 Countermeasures Amplifier functions employ a sophisticated automatic gain control circuit that is superior to most audio amplifiers.
-
Product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
-
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
Airflow Testing Instruments
-
Kanomax USA is one of the leading manufacturers of airflow testing instruments for HVAC Testing, Cleanroom Monitoring, Industrial Manufacturing, and much more. Our airflow testing instruments include air velocity meters, airflow capture hoods (i.e. balometers), micromanometers, a duct air leakage tester, high temperature anemometers, transducers, transmitters, and multi-channel anemometers.
-
Product
Instrument Transformer
-
Our company has achieved a reputed niche in international market by manufacturing and exporting a great range of Instrument Transformer. Widely used in electrical, power generation and engineering sector for transforming voltage or current level, this equipment is in accordance with industry standards. Manufactured using excellent grade raw materials sourced from reputed vendor, Instrument Transformer is offered to clients in different technical specifications. We stringently test this instrument on varied standard parameters.
-
Product
Pump & Motor Testing Instruments
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump and Motor Testing Instruments - dynanometer, stator rotation direction detector, digital RPM meter, DC power analyzer, motor analyzer.
-
Product
Wide Angle Scale Instrument
LS-110 LS-80 Hz
-
Standard Electric Works Co., Ltd
● Easy to read long-scale and pointer-indications can easily be read from a distance.● Full Scale Deflection : 250°● Accuracy : Class 1.5● Scale Length : LS-110 : 183mm LS-80 : 140mm● Case and Composition : Acrylic resin cover, plastic with UL body and terminal, Four studs mounting. LS-110 case : plastic body option 1 : plastic body with metal case, no UL option 2 : metal case, no UL exception : W, VAR, PF (3P4W)● Color : White scale plate, black terminal plate, black meter body.● Pointer : Sword-type in black color.● TAUT BAND / Pivot & Jewel for LS-110.
-
Product
Free Space Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
DC-Coupled Pulse Amplifiers
-
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
Product
Transimpedance Amplifiers
-
Artifex Engineering GmbH & Co. KG
Applications include photodetection with PMTs and photodiodes, spectroscopy, Scanning Tunneling Microscopy, ionization detectors, pyro and piezoelectric detectors.
-
Product
Premium Headphone Amplifier
A 2
-
A premium model with a discrete configuration and full analog circuit that was created to drive the T 1 thoroughly.
-
Product
Handheld Fiber Test Instruments
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
portable, battery-powered devices used by field technicians to install, certify, troubleshoot, and maintain fiber optic networks.
-
Product
Power Amplifier
-
The Model LN power amplifiers offer extended output power, voltage capabilities, lowdistortion, versatility and the latest BJT power in the operational amplifier technology. All theseperformance features are not available in other power amplifiers.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
Limiting Amplifiers
-
Teledyne Microwave Solutions (TMS) offer a range of Limiting Amplifiers which are used in instantaneous frequency and phase measurement receivers. The most important performance requirement of a limiting amplifier is to minimize output power variations, and provide a constant output over a wide input dynamic range.
-
Product
Amplifiers
MMICs
-
RF core has been innovating GaN-based MMIC solutions for active phased array system pursuing more ease of use, higher performance, lower SWaP (Size, Weight, and Power) as well as lower cost. We aim at integrating all components of TRM front-end for active phased array on single die.
-
Product
Power Amplifiers
-
Power Amplifier is used to amplify the output of the CS700A or CS701 signal generators. The 52 MHz bandwidth amplifier can swing 36Vpp with an output current up to 1A continuous. The CS1070 includes an internal inverting power supply to provide the negative rail, simplifying power supply requirements. The gain is fixed at x10 (20dB). The output voltage range is ±5V to ±18V and asymmetrical to +31, -5V for PSRR measurements right up to 30V as the input supply increases past 20V.
-
Product
Optical Plummet Instrument
TELIM
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Magnification 42x*Aperture 50mm*Cross levels (20‘‘/2mm)distance approx. 800m*Accuracy ± 1mm/100m*Made in Germany
-
Product
Nanomechanical Instruments For SEM/TEM
-
As the world leader in nanomechanical testing systems, Bruker makes it easy for you to conduct in-situ mechanical experiments in your microscope with the Hysitron PI Series PicoIndenters. Our unique transducer design delivers unmatched stability throughout your experiments, resulting in precise data even at the nanoscale. Video capture from the microscope enables real-time monitoring and direct correlation of mechanical data to microscope imaging. With solutions designed to fit many of the microscope brands in use, you are sure to find one that is ideally suited to your research.
-
Product
GaN Amplifiers
SBP-3233831838-KFKF-E1-HR
-
Model SBP-3233831838-KFKF-E1-HR is a power amplifier with a typical small signal gain of 18 dB and a nominal Psat of +38 dBm across the frequency range of 32 to 38 GHz. The DC power requirement for the amplifier is +30 VDC/2 A. The mechanical configuration is an inline structure with K(F) connector as its input port and output port. Other port configurations, such as K connectors and WR-28 waveguides for either the input or output, are also available under different model numbers.
-
Product
PWM Amplifiers
SA X-Series
-
MCS high power brushless motor drives combine high bandwidth with high current for demanding direct drive applications up to 100KVA. Backward compatibility with all MCS drives..
-
Product
Precision DC Source Instrumentation
-
High power, dual channel PXI User Power Supplies as well as precision DC source instrumentation. These products are offered in both PXI and GTXI formats.
-
-
Product
Instrumentation & Control
-
Rotork offer high performance and precision for all instruments and related products; intrument valves, controllers, and measurement
-
Product
Differential Pressure Instruments
-
The testo 512 differential pressure meter is available as four models. This model has a measuring range from 0.0.29 psi and is ideal for measuring pressure differences at filters and for carrying out pitot static tube measurements in air ducts at air flow speeds between 16 and 180 fps.
-
Product
Phase Domain Induced Polarization/Resistivity Instruments
ULTRA MiniRes
-
*Light weight yet durable*Low power consumption*Lowest cost in the industry*Exploration to greater than 1000 feet**2.5 HertzMEASURES:*Earth resistivity*Induced polarization
-
Product
Gas Measuring Instruments
N Series
-
Teledyne Advanced Pollution Instrumentation
N Series Gas Measuring Units for SO2 (Sulfur Dioxide), NO, NO2, NOX (Nitrogen Oxide, Nitrogen Dioxide), CO (Carbon Monoxide), CO2 (Carbon Dioxide), O3 (Ozone), True, Direct NO2, NOX, NO, CH4 (Methane), THC (Total Hydrocarbons), and more
-
Product
Audio and Electro-Acoustic Measurement Instrument
CLIO 11 FW
-
CLIO 11 is the Next Step forward in the CLIO software family of products for the CLIO System, building up the well-known CLIO 10measurement suite.The CLIO System with CLIO 11 software is a complete audio and electro-acoustic measurement instrument that gives state-of-theartsolutions to laboratory, on-field and production-QC applications. CLIO 11 is designed to support and drive the existing hardware likethe FW-01 Audio interface and is ready to accommodate its future developments; operating system support has been extended to thelatest Windows 8.
