Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
Product
pH Pocket Water Quality Meter
LAQUAtwin pH-22
-
The only pocket meter that directly measures pH in 0.1ml sample (or 0.05ml sample with sampling sheet B). Unique sensor allows measurement of viscous liquids, solids, and even powder samples. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the flat sensor. This procedure saves you time and prevents wasting your precious sample.
-
Product
Strip Tension Measurement
-
ABB’s strip tension system is the perfect choice for measuring strip tension in hot rolling, cold rolling and process lines.Accurate strip tension measurement is a prerequisite for keeping the strip tension constant within the desired range, during both acceleration and deceleration. This allows for optimal strip quality, increasing process uptime and preventing strip breaks. The system is proven to be exceptionally robust and resilient to high forces as well as aggressive mill agents. The load cells are calibration free, can withstand overloads up to 10 times the nominal force, and have an impressive life length. The load cells come in different sizes up to 200 kN.
-
Product
Reflective Memory
-
An innovative solution designed to provide highly deterministic data communications for your real time applications such as distributed simulation.
-
Product
DC Electronic Load Control Software
EES-100-xx
-
EES-100 Software controls all electronic load types. ( Single & Dual channel) data logging, constant current, constant voltage, constant power, constant resistance, up-down timing, V/I Curves, Graphing, Response Testing
-
Product
LAN Cable Tester
21-6566-00
-
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
-
Product
Multichannel Analyzers
-
Multichannel Analyzers (MCAs) are workhorse instruments in many scientific measurements. An MCA analyzes a stream of voltage pulses and sorts them into a histogram, or “spectrum” of number of events, versus pulse-height, which may often relate to energy or time of arrival. The stored spectrum may then be displayed and analyzed.
-
Product
Radar Water Level Gauge
HR7311
-
HighReach Measuring & Controlling System Co.,Ltd
The HR7311 radar water level gauge is a high-precision, low-power non-contact radar level gauge designed by our company. It can be used for surface (or pipe network) water level measurement; due to its pulse coherent radar (PCR) Having with the traditional pulse radar level gauge, the technology has higher measurement accuracy and lower power consumption, as well as ultra-small volume. At the same time, it uses 60G sub-millimeter radar wave as carrier signal, so it has high precision And small size. The volume and energy saving features make it independent of temperature gradients, water vapor, water contaminants and sediments. The optimized algorithm makes the measurement results more accurate.
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
PCI BUS Interface Card
PCI301
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
Pro-Stik II Level Sensor
7330
-
The Drexelbrook 7330 Pro-Stik II Series are intrinsically safe programmable liniear position sensors ideal for monitoring in a variety of liquids and tanks.These position sensors are based on the proven magnetostrictive technology and are available in different models including our popular explosion proof and flame proof models. The 7330 Pro-Stik II position sensors are loop powered and available with a rigid 316 stainless steel or flexible PVDF materials.The probe features a security feature by utilizing a timing sequence that is used to unlock the probe for programming. This ensures that the span cannot be accidentally programmed by someone in the field.All of the sensor's electronics are SMT components integrated into the 5/8" diameter sensing tube offering greater options for insertion and mounting in tanks and vessels.
-
Product
DMX Recorder
XRC-200
-
The XRC-200 is an easy to use DMX recording and replay unit. The operating concept is similar to a CD player and can be used by non-professionals. The sequences are recorded from a lighting console, or other DMX output device, onto the device. The XRC-200 replays the recorded sequences in real time.
-
Product
Energy Storage/Backup Power
-
Broadband service providers are challenged to reduce their carbon footprints and at the same time expand the reach and performance of their networks to meet escalating subscriber demand. The adoption of an eco-friendly energy storage and backup powering system based on hybrid supercapacitor technology enables service providers to achieve both goals while simultaneously improving network reliability and reducing capital and operational costs. ATX’s Areca™ Energy Storage Solutions include next-generation hybrid supercapacitor modules that offer significant improvements over existing standby power sources, such as valve regulated lead acid (VRLA) and Lithium-based batteries.
-
Product
Mission Data Programmer
MS 1602
-
The MIP programmer is used to program, read and erase mission data of Mirage 2000 Aircraft. This system is micro controller based design. This system facilitates to program the four EPROM devices at a time. This system contains four read write slots and one read only slot. Read only slot used to read the device data safely. System also has capability to program the one slot device data to another slot device.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
43-182B-003
-
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
Computer-Based Instruments
GT668PXIe
-
GuideTech’s GT668PXIe PXI 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system at low cost. High accuracy 100MHz time base with NIST traceable calibration. Some of the GT668PXIe-1 measurements include Jitter measurements, PLL & Clock Jitter, Spread Spectrum Modulation, PLL Lock Time, Frequency, Period, Pulse Width, Skew, Tpd, Rise/Fall Time, Time Interval Error and more.
-
Product
PXI High Density MUX BRIC, 32-Chan, 10-Pole
40-570-412
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Timing Controller
MS 2009
-
MS5128 Timing Controller has programmable logic generation, Input Output Signals Interface, Timings, macro-cells, Pins, internal timing delay and Signal Levels for airborne microprocessor boards.
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
-
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Towing Dynamometer
RS-10K
-
RS-10K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-10K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
Product
and EET200E - Encoder Emulator Tester
EET-200
-
End the shotgun approach to troubleshooting and reduce the time spent diagnosing altitude encoder/transponder problems. TRANS-CAL INDUSTRIES' EET-200 and EET-200E offers the avionics technician an inexpensive diagnostic tool for altitude encoder/transponder troubleshooting.
-
Product
Automotive Sensors
-
Vehicle electrification (e-mobility), sustainability (zero emissions), increased safety & productivity are trends significantly impacting the role of sensors in passenger and commercial vehicles. This includes the requirement to enable greater e-motor performance and efficiency, reduced charging time, increased battery life, cleaner and more efficient internal combustion engines, reduced maintenance / vehicle down-time as well as highly robust ADAS and autonomous driving safety systems. TE offers a diverse sensor technology portfolio, combined with deep application expertise gained from extensive experience of delivering quantifiable value across a wide range of demanding passenger & commercial vehicle applications.
-
Product
In-Circuit Test Fixtures
-
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
Product
External Temperature-40 to +125C
TGIS-0020
-
This model is battery powered and measures temperature using an external probe, providing cost-effective environmental monitoring ideal for inaccessible locations or where a faster response time is required.
-
Product
Semiconductor Thermal Transient Tester
T3Ster®
-
T3Ster (pronounced "Trister") is an advanced thermal tester from Mentor Graphics MicReD Products for thermal characterization of semiconductor chip packages. Superior to all other thermal characterization equipment on the market due to its speed and ease of use; its extremely accurate temperature measurements (0.01oC); and its 1 micro-second measurement resolution in time.
-
Product
LANTIME Stratum 1 Server for all networks
-
Meinberg Funkuhren GmbH & Co. KG
Our Network Time Protocol (NTP) is the only way to get the most out of your network, to-use time server appliances.
-
Product
CompactPCI Card
IIB-429-CPCI
-
The IIB-429-CPCI provides from ARINC-429 compatible channels (2 receive and 2 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-CPCI is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This CompactPCI card has a 3U form factor. This unit is also available in a 6U form factor (IIB-429-CPCI-4C) with four times the functionality
-
Product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
-
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Digital (1kV up) H.V. Insulation Tester
6213A IN (Ranges: 0.5kV to 10kV 0.5kV increment steps)
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 ×16 characters; large intelligent LCD module.● 20 Insulation test voltages 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV.● Ener-Save™ feature to extend battery life.● Bar-graph indicates test voltage; rise and decay can be observed.● Visual and audible warning if external voltage is present (>500Vac or Vdc.)● Insulation resistance; auto-ranging on all ranges.● Overload protection.● Low battery indicator (read time battery voltage measurement).● Measures insulation time duration of the test.● Low battery consumption.● Better than 10% accuracy on all ranges.● Auto-off.● Calculates Dielectric Absorption Ratio (DAR) automatically.● Calculates Polarization Index (PI) automatically.
-
Product
FlexMobile 429+
-
The FlexMobile 429+ is a lightweight and portable device that supports ARINC 429 and Discrete, with precise timing and flexible programming. It comes with various ARINC 429 options, 28V open-collector Discrete Inputs/Outputs with software-selectable directions and Ethernet/USB connectivity. It also has extensive error injection and detection capabilities, 10 ns timing accuracy, and support for various software interfaces such as Multibus, MX-Foundation 4 API, MAXIM GUI, and MAXIM Air GUI. The device also supports synchronization with other FlexMobile devices and IRIG-B Sync.
-
Product
1435 Series Signal Generator (9kHz to 40GHz)
1435
-
1435 series signal generator achieves balance in terms of performance, economy and volumetric weight. It responds fast and switches to another frequency in only 1ms, which shortens the test time and improves test efficiency, meeting the needs of massive data testing.
