Voltage Transducers
See Also: Voltage Sensors
-
Product
Voltage Calibrators
-
Practical Instrument Electronics, Inc.
PIE has a voltage calibrator to fit your needs from the PIE 235 voltage and pH simulator to the advanced troubleshooting capabilities of the PIE 532 milliamp and voltage calibrator. The PIE 532 includes our patented Loop Diagnostic Technology! All the voltage/milliamp calibrators have fuse-less protection, rugged design and long battery life. With the PIE 535, source 4 to 20 milliamps or 10 to 50 milliamps into loop instruments and drive final control elements such as valves and actuators with up to 42 volts.
-
-
Product
Voltage Dividers
-
Measurements International Ltd.
A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.
-
Product
Low Voltage Detectors
LVD-17
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled smart voltage detector.● Bright LED and audible alarm sound when voltage is present.● Designed for non-contact voltage detection.● Sensitivity adjustable with thumbwheel.● Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits.● LED indication for battery condition.● Identify Hot and Neutral.
-
Product
Active Voltage Probes
-
Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the active voltage probe becomes the everyday probe for all different types of signals and connection points.
-
Product
Pressure Transducers
-
Alicat Scientific, Incorporated
Use pressure transducers to rapidly measure absolute, gauge, or differential pressure. Common configurations include portable and anti-corrosive designs. Custom build options include anti-corrosive and portable configurations.
-
Product
Voltage Probe
VOL-PBE
-
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
Product
Acoustic Emission Transducer
GT301
-
Acoustic emission transducer GT301 converts acoustic signal into electrical signal, parameters of which are used for acoustic emission source evaluation.
-
Product
AC Current Transducer
iDVM 333
-
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
Product
Uniload Voltage Transformer
2J4-4
-
The Type 2J4-4 Knopp Uniload Voltage Transformer Test Set consists of three major parts:
-
-
Product
Combined Pressure and Temperature Transducers
-
We offer some different styles of combined pressure and temperature transducers which are well suited to Motorsport applications. These include the EPTT5100 combined pressure and temperature transducer, which, has an internal temperature sensor, and the miniature EPTTE1400 combined pressure and temperature transducer which has an external temperature probe.
-
Product
Voltage logger0 to 25V
TK-4702
-
Supplied with an input cable, this logger can measure voltages up to 25V DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.
-
Product
Battery Voltage Recorder
BVR Series
-
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and temperature.The BVR Series is the perfect tool for that purpose. All measurements are automatically saved in device’s internal memory. Additionally, DV-B Win software helps the user to download all measured results. Furthermore, the user can create test reports and export them to various formats.BVR series includes two models: BVR11 and BVR22. These are rechargeable handheld devices intended for performing monthly battery inspections and support tools during capacity testing. The list of the applications of these instruments includes:Efficient supplement to BLU series of battery load units during battery discharge testingMonthly inspections of large battery banksAmbient temperature measurementCurrent measurement using current clampsUSB and Bluetooth communication with PCSimultaneous string voltage and current measurement to analyze a discharge test processThe BVR22 model provides Bluetooth communication with an external density meter, for transferring electrolyte specific gravity and temperature readings.
-
Product
Non Contact Flange Torque Transducer
FF425
-
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
Product
Power Frequency Transducer
TDF
-
Kusam Electrical Industries Limited
• Dual Aux. Power 110/220V AC• High Accuracy 0.2% RO at 23 °C± 5 °C• High Dielectric Strength 2.6KV AC / Min, Between Input / Output/ Power Case• ABS Plastic Case, DIN Rail or Wall Mounting
-
Product
Wireless Transducers with GSM Modem
-
Wireless GSM data loggers for temperature, humidity, binary-u. counter input.
-
Product
VLF Voltage Generators
-
Fivestar HV Testing Equipment Co., Ltd.
VLF hipot is an AC output tester with an output frequency of 0.1 Hz or lower rather than 50/60 Hz. Although the frequency is very low, it is an alternating current with polarity reversals every half cycle.
-
Product
Withstand Voltage Tester
2672AM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
Product
Voltage Controlled Oscillators
-
Mercury Systems’ VCOs (Voltage Controlled Oscillators) offer predictable consistency, rugged design and reliable performance. Our VCO products will meet your application’s most demanding stability and low phase noise requirements; featuring wide tuning bandwidth up to an octave. With custom designs and space qualified versions, trust Mercury to provide the VCOs for your next design.
-
Product
Voltage Testing
VisualDetect series
-
Hachmann Innovative Elektronik
With the VisualDetect line you get a type series of handy, exact and easily operated voltage detectors and maintenance testers.
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
Product
Voltage Control Attenuator
-
Voltage variable attenuator offering infinite attenuation precision and broadband performance
-
Product
3-Axis AC Magnetic Transducer
3DACMT-1
-
The *SENIS* 3DACMT-1 is a cutting-edge 3-Axis AC Magnetic Transducer designed for precise measurement of alternating magnetic fields. It operates within a frequency range of 10kHz to 200kHz, making it an ideal choice for applications requiring high sensitivity and precision. The device features a compact sensing cube with a volume of about 3.6 cm³, ensuring non-invasive measurements that do not disturb the magnetic fields being observed. With its exceptional resolution of better than 1.5μTrms, the 3DACMT-1 delivers a highly linear response and transduction accuracy of ±1%, ensuring reliability even in the most demanding environments. Further, the *SENIS* 3DACMT-1's design incorporates three mutually orthogonal coils, allowing it to capture all three components of magnetic fields simultaneously while being insensitive to electrical fields or capacitive coupling. The sensor's excellent angular accuracy of <±1° and phase accuracy of <3° at 85kHz enhances its capability to provide accurate data. Additionally, with an output signal from 0V to ±5V, and a measurement bandwidth of 10kHz to 200kHz, this transducer is built to handle complex measurement tasks efficiently.
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-15KVe
-
The MI-15KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 3.000.000 MΩ with four test voltages: 1 kV - 5 kV - 10 kV and 15 kV.
-
Product
Voltage Tester
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Voltage Tester is a testing instrument used for electrical power testing purposes. It is mainly used for detecting the presence of AC voltage in or around the object or surface and is very easy to operate.
-
Product
Pressure Transducers
-
Procter & Chester Measurements Ltd
A transducer is a generic name that is a device which is usually electronic that coverts a physical attribute to a measurement signal.
-
Product
Transducers with 4-20 mA Output
-
Transducers / transmitters for temperature, humidity, atmospheric pressure and CO2 with 4-20mA interface.
-
Product
Voltage Controlled Oscillators
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a variety of voltage controlled oscillators (VCOs) that generate frequency in aerospace and defense, point to point, CATV Satcom and other Radio applications. Our surface mount hybrid and MMIC VCOs support a variety of applications operating between the 45MHz to 14.2 GHz frequency range. Featuring low phase noise, stable performance over temperature, low power consumption, and highly linear tuning, MACOM’s VCOs provide leading edge solutions for challenging communications needs.
-
Product
AC High Voltage Tester
VHT
-
VEER make High Voltage Tester VHT is specially designed to test Dielectric Strength of Device under Test as per applicable standards. High Voltage test is required to determine whether test object has proper insulation or not. High Voltage test is carried out as Routine Test Each device is subjected to test at high voltage of 1 kV + 2 x (working Voltage)If Insulation is weak then device will consume more power because of leakage current which causes more heat. Heat will reduce the reliability and overall life of device under test It is also responsible for high risk of electric shock. So, High voltage test is necessary for all electrical equipments.
