Active Filters
Require power to operate, using active devices and passive components in a frequency-selective network, only passing certain frequencies.
-
product
Active Differential Probe, 100 kHz to 12 GHz
U1818B
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Bandpass Filters
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
product
Switched Filter Banks
K&L Microwave provides Switched Filter Bank (SFB) products built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications. Use the quote cart to request a quote on an existing design or to provide specifications for a custom design.
-
product
High Impedance Active Probes
12C
A high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf and the rise/fall times are 0.8 ns. This instrument has full dc capability and can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 and with a 50 Ohm input, signal attenuation is 20:1.
-
-
product
Super-Notch YIG Band-Reject Filters
YIG Tuned BRF patented technology gets closer to the ‘perfect notch'. Leveraging a long heritage of engineering innovation in YIG technologies, Teledyne RF & Microwave has developed a line of YIG Tuned Band-Reject Filters powered by patented new technology that overcomes many long-time design limitations inherent to YIG Band-Reject or “notch” filters. Our new line delivers major advancements and unequalled performance.
-
product
Fabry-Perot Based Scanning Filter
This new type Fabry-Perot Based Scanning Filter (FPSF) is based on Optoplex proprietary fiber optical Fabry-Perot Etalon technology. It offers F-P based scanning filter with central wavelength at 1060nm, 1310nm, 1550nm or other customized wavelength. It can be tuned manually or automatically by scanning over a wide spectral range from 10nm to 100nm with bandwidth from 0.05nm to 1.0nm. FPSF features less than 3dB insertion loss and as high as 1kHz scanning frequency. Its unique high reliability and low insertion loss design presents the most cost-effective solution for OEM application from telecommunication to fiber sensing interrogation.
-
product
Active Type Hydrogen Frequency
CH1-1003M
Hydrogen frequency and time standard Ch1-1003M is designed for precision storage and reproduction of the size of frequency and time units as part of measures and reference complexes. Main applications: – national time and frequency services; – ground stations for tracking and control of satellite radio navigation systems; – radio interferometry with extra long base.
-
product
Active Temperature-Humidty Transmitters
HD48… Series
HD48 transmitters are designed for temperature and humidity control in conditioning and ventilation applications (HVAC/BEMS) in the following sectors: pharmacy, museums, clean rooms, ventilation ducts, industrial and civil sectors, crowded places, canteens, auditoria, gyms, high-density farms, greenhouses, etc.
-
product
High-Power Filters
Beehive Electronics designs custom high power RF filters used in vacuum coating systems. Our experience spans from kilohertz to gigahertz and power levels up to 50 kilowatts. We provide a turnkey solution: we design, build, and test the filters to the customer's specification.
-
product
Neutron Activation Analysis
Neutron Activation Analysis (NAA) is one of the most sensitive analytical techniques used for multi-element analysis available today. The NAA procedure is capable of providing both quantitative and qualitative results for individual elements, with sensitivities that can be superior to those possible by any other analytical technique. Elemental Analysis Incorporated (EAI), as an innovator in the development and application of radio-nuclear chemistry analytical techniques, now offers its clients the ability to analyze some 75 individual elements (including certain organic elements) by NAA at trace and ultra-trace concentrations. Moreover, by developing scientific liaisons with selected nuclear reactor sites in North America, EAI is able to offer customers the expertise and capabilities of the premier scientists and research facilities available today. Combined with EAI’s tradition of excellence in customer service and technical assistance, EAI is uniquely positioned to assist clients with timely, cost-effective, and reliable trace element analysis for almost every conceivable field of industry or scientific research.
-
product
Filter Test System
DU7216/7218
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
product
Noise Suppression Products / EMI Suppression Filters / TVS Diodes (ESD Protection Devices)
Murata noise suppression products include compact EMI suppression filters that efficiently eliminate noise, L Cancel Transformers (LCTs) that greatly suppress noise in high-frequency bands by reducing the ESL generated inside capacitors and in boards, and TVS Diodes that guard semiconductor devices against electrostatic discharge from external sources. Murata supplies products that support a variety of approaches to suppressing noise.
-
product
Vacuum, Module, Receiver, 90 Series, 2 Port Positions w/ Filter
510104266
Primary mating module 510108242. (May mate with other ITA modules, as well.)
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF120
Lifasa - International Capacitors, SA
Accessories: Differential protection
-
product
LCL Filters
LCL Type Harmonic Filter Modules are used to filter out the input current harmonics of the Motor Drives having six-pulse diode/thyristor rectifiers, where harmonic current distortion exceeds the limits defined in standards.
-
product
InfiniiMode Active Differential Probe, 1.5 GHz
N2750A
The N2750A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation.
-
product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
-
product
Semrock Optical Filters
IDEX Health & Science offers a comprehensive line of Semrock optical filters. We set the standard in performance, quality, and reliability for the life science, point-of-care, clinical diagnostic, and analytical instrumentation industries. We have applied patented design techniques to create some of the most spectrally sophisticated optical filters on the market. Whether you select from our extensive catalog or we design a custom filter to your exact specifications, you can be confident of our uncompromising quality, reliability, and reproducible results.
-
product
Active Monopole Antenna
AM-741
The 41 inch Monopole antenna is required for making electric field emission measurements below 60 MHz per Military standards (MIL-STD-461) and FAA (DO-160) specifications. This antenna is for emissions measurements only. It cannot be used for transmitting. The Active Monopole antenna is generally used in a shielded room or in a screen room, with the equipment under test (EUT) placed on a metal ground plane. The 41 inch rod and the ground plane behave electrically as though a mirror image of the rod were located below the ground, and the ground removed. Since the stainless steel plate does not have enough surface area to mirror the entire 41 inch rod, it is bonded to the surrounding ground plane during use. The AM-741 is battery powered to prevent measurement errors that maybe caused by external power cables. The ANSI equivalent capacitance substitution (ECSM) method is the recommended method for calibrating AM-741 monopole antenna. The individual calibration data will be included with each antenna.
-
product
Wide Band Filters (multi-octave)
NANO-ERF® Series
The NANO-POLE® Extended Range Series of tunable filters was developed to address applications needing an extremely small surface-mount package with low power consumption. Wide tuning range is accomplished with careful design to minimize size and power consumption.
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-3F
Programmable, 2-Channel Low-Pass Filter Module. The AAF-3F is designed for use with the AAF-3M and AAF-3PCI filter boards.
-
-
product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
product
InfiniiMode Active Differential Probe, 6 GHz
N2752A
The N2752A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2752A probe’s InfiniiMode provides the following modes of operation.
-
product
Active Hot Parameters For E5081A ENA-X And E5080B ENA
S96111B
The S96111B active hot parameters are available on ENA-X or ENA network analyzers and provide a more accurate method to test hot S-parameters, gain and output power than traditional methods by utilizing X-parameter technologies. Restricted to 50 GHz.
-
product
Gas Filter Correlation CO2 Analyzer
Model N360
Teledyne Advanced Pollution Instrumentation
The Model N360 measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
product
Filter Design System - Mode Analyser
EA-300
The EA-300 is a stand alone unit with internal firmware and a large colour display. It connects to the outputs from a standard LISN and feeds the results to any standard EMC analyser or receiver. The EA-300 prompts the user through the steps necessary to fully characterise the emissions from the EUT, then will output via the screen the recommended filter component values that would reduce these emissions to acceptable levels.
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3PCI
The AAF-3PCI is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier PCI bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
