-
product
Back Pressure Test Kit
389
Thexton Manufacturing Company, Inc.
Aids in diagnosing clogged or restricted exhaust systems.
-
product
Power Module Tester
The Power Module Checkout ATE is developed for testing DC-DC Power modules typically utilized in India's space program. The DC-DC converters are exhaustively tested for all design parameters including supply voltage range, line and load regulation, efficiency, ripple, noise, transient response and so on. Special power sources and loading mechanisms are deployed to enable testing of various types of power modules.
-
product
Motor Exhaust Gas Analyzer
MEXA-ONE
MEXA-ONE offers an intuitive user interface with a highly efficient hardware and software design.This results in increased testing efficiency and economical facility operation, while enhancing reliability and accuracy. These advancements are possible because the MEXA-ONE software employs new "HORIBA ONE PLATFORM". This platform integrates the test devices in an emission cell into a single user interface, increasing efficiency and optimizing user control over the entire testing process.
-
product
Dual Pitot Tube Flow Meter
PTFM-ONE-DT
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
-
product
Peugeot Oxygen Sensor
KS60113 - Peugeot
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
product
Laser Induced Incandescence (LII)
Soot is considered a hazardous pollutant emission and is typically a result of incomplete combustion processes, and thus is also related to combustion performance. Laser Induced Incandescence (LII) is a laser-optical measurement technique dedicated to soot diagnostics. LII can provide measurements of soot volume fraction, such as in Diesel engine exhaust, and even instantaneous images of soot distribution during formation inside a running IC engine.
-
product
Digital Transformer BDV Oil Test Set
We are engaged in manufacturing, supplying and trading an exhaustive range of High Voltage Oil Test Set, which is developed under the constant supervision of our team of experts. This equipment is acknowledged for its optimality in performance and quality.
-
product
Smart Optimization
A reflow oven or wave solder machine is capable of literally billions of alternative setups. Each combination of zone temperatures and conveyor speed will produce a unique profile for a processed product. KIC's software makes an exhaustive analysis of all the setups and it recommends the very best oven/machine recipe within seconds.
-
product
Load Bank
RLB
RARA manufactures load banks, ranging from small portable units for testing generators to multi-megawatt designs for larger applications. Regular load testing, along with correct battery maintenance, is the best way of ensuring the reliability of standby power systems. It is routine for all newly-installed generating sets to have a load test during the commissioning process in order to prove the performance of the set and all ancillaries-cooling system, exhaust system, switchgear and protection schemes.
-
product
Dilution / Sampling Systems
HORIBA offer a full range of full flow CVS and partial flow systems for exhaust gas measurement that cover the requirements of all of the global emissions standards. These are complemented by a full range of solutions for the measurement of particulate mass and particulate number required to meet the latest legislative standards.
-
product
THREE WAY BACK PRESSURE KIT
TU24APB
*Allows quicker and more accurate testing of exhaust blockages in catalytic converters, mufflers, etc*2-1/2" gauge features two multi-colored bands - idle and 2,500 RPM - with pressures shown in PSI and bar*Includes 6' of hose, enough length to test from driver's seat
-
product
Mobile Testing
Mobile devices are inarguably the most disruptive technology invention in recent times and have had an impact on human lives like no other. With a number of mobile devices surpassing the number of human population on earth, making your application mobile-ready is key to keeping today’s digital consumers happy. Across enterprises of all sizes, mobile apps have fuelled growth in the business operations and customer services. However, with the variety of platforms, devices and networks, there is significant infrastructure required for mobile application testing. The testing either is not exhaustive or very costly due to the sub-optimal approach used for testing.
-
product
Vibration-Rotation Excitation Bench
·Realizing rotation-vibration excitation operation suitable for vibration test of gear, endurance test of engine accessory·Rotation-vibration excitation operation equivalent to engine vibration excitation1 Reproducing rotation speed fluctuation and torque fluctuation2 Reproducing engine explosion fluctuation3 Reproducing waveform in engine starting·Environmentally friendly compared to the engine bench1 No need for fuel system facility2 No need for exhaust gas treatment3 No need for taking fire prevention measures
-
product
Laser Spectroscopic Motor Exhaust Gas Analyzer
MEXA-ONE-QL-NX
The MEXA-ONE-QL-NX is an analyzer for the direct, simultaneous real-time measurement of the four relevant nitrogen-containing exhaust gas components NO, NO2, N2O and NH3.The analyzer combines a light source based on the new quantum cascade technology (efficient lasers in the mid-infrared spectral region) with a precisely adjusted dual path cell to measure low concentrations with maximum sensitivity. The detection limit complies with current European legal requirements.Furthermore, the MEXA-ONE-QL-NX offers wide measuring ranges of up to 5000 ppm (for NO). By using extremely narrowband light sources and measuring under reduced pressure the cross-sensitivity to other exhaust gas components can be drastically minimized.The complete measuring system - including filtration - is specifically developed for the measurement of NH3 and thus guarantees a very fast NH3 rise time (T10-T90) of less than 5 seconds. The MEXA-ONE-QL-NX can be operated as a stand-alone analyzer or integrated into the MEXA-ONE software interface for user-friendly and simplified system operation.
-
product
Lambda Sensor
KS60121
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
FIAT Oxygen Sensor
KS60113 - FIAT
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Micro Dilution Tunnel
MDLT-ONE
The MDLT-ONE is designed to sample particulate emissions using the partial flow dilution method. A small portion of the total exhaust is diluted with HEPA* filtered air to create a constant flow rate through particulate filters to collect Particulate Matter (PM). Compliant to the latest regulations, the new MDLT-ONE is very compact and offers faster response by the use of high precision venturi flow meters and a piezo actuated valve.
-
product
Exhaust Gas Thermocouples
8TR4C Series
The AMETEK 8TR4C Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested, and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading older style Exhaust Gas Thermocouples.
-
product
Emission Measurement Technology
Maschinenbau Haldenwang GmbH & Co. KG.
When measuring exhaust gas, the CO concentration or - in diesel vehicles - the smoke gas opacity is measured. In this way it can be determined whether the exhaust system meets the legal requirements and is in perfect condition.
-
product
Dynanometer Roller Set
FPS 2700 | VP 230048
Maschinenbau Haldenwang GmbH & Co. KG.
The FPS 2700 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. As a result of the increased tractive force of its eddy current brake, the FPS 2700 is additionally suitable for power measurements at constant speed and constant tractive force.
-
product
Chemiluminescence Oxides of Nitrogen Analyzer
Model T200
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T200 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Vivarium Rooms
Darwin Chambers Company ALAAC, OLAW, USDA, and NIH-compliant Vivarium Rooms are designed for maximum value, sustainability, and conformance with applicable standards. We have over a decade of experience in working with researchers to provide humane and often precise conditions to meet their unique and specific needs. Vivariums are commonly defined as a place, such as a in laboratory, where live animals and/or plants are kept under conditions simulating a natural environment. Often, these contain both plants and animals, within a micro-ecosystem, often with controlled stability or controlled change of environmental variables. We offer various surface finishes, including all stainless steel, which are easy to maintain and may be sterilized to cleanroom standards. Compartmentalized enlosures are offered, which are modular and reconfigurable. Our rooms will accommodate plants as needed (we also provide plant growth chambers), and we offer control of humidification in conformance with current ALAAC mandates, sufficient air exchanges, available HEPA filtration of intake and/or exhaust air, standard screened equipment hous- ings, and other such considerations.
