Leakage Current Testers
-
product
Peel Force Tester
PT-55
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
product
6-24V Heavy Duty Circuit Tester
1654
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 24V systems.
-
product
SOLAR CELL TESTER
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
product
Wafer Tester
Tokyo Electronics Trading Co., Ltd.
A vital step in the Semiconductor Value Stream, focusing on electrical screening and consumption of Known Good Die (KGD).
-
product
Semiconductor Testers
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
product
Load Cell Simulators / Testers
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
product
MEMS Device-Oriented Testers
Are your test requirements oriented to defined families of devices, with common characteristics? You do not need to purchase an expensive, general-purpose mixed signal tester: You can rely on SPEA DOT 100, a system designed to answer the test requirements of MEMS and other low-pin-count devices at an incredibly low cost.The DOT 100 is based on a revolutionary per-device architecture: each device under test has a dedicated CPU managing the entire test process, while each card hosts all the resources for the parallel test of 3 devices, in the size of a postcard.
-
product
Installation Tester
M75
Installation tester for safety tests according to IEC/EN61557-1 with TRMS multimeter functions and test of cable mapping on lan RJ-45 networks
-
product
30 AMP Fuse Buddy Testers
FB305M
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
product
Handheld Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
product
Memory Burn-in Tester
B6700 Series
B6700 can test as many as 48 burn-in boards in parallel at speeds up to 10 MHz, which helps memory suppliers get their newest products to market faster while also reducing testing costs. An original high performance chamber improves yield by assuring high temperature accuracy while generating high temperature. It also shortens the temperature rise and fall time which leads to shortening the test time.
-
product
Current, Voltage, Resistance
Solutions for the testing and calibration of current, voltage and resistance are used in industry (laboratories, production, workshops), in calibration service companies and in quality assurance. These instruments are portable and mobile and are particularly notable for their low measurement uncertainty and high scope of operation.
-
product
Insulating Oil Testers
US, A, AD Series
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Confirms to IS 6792, IEC 156 • Tests insulating oils to IS, IEC, ASTM, etc.• Test voltage to 100kV• Motorized rise of test voltage: 2kV/sec • One piece construction with safety interlocked transparent hood covering test cell• Test voltage can be held at any desired level• kV meter continues to indicate breakdown voltage even after breakdown• Light weight: 36 kg only• Portable, rugged and with cover.
-
product
Pitot Static Tester
ADSE 746
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
product
Clamping Voltage Tester
MIG0603CLV2
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Polarization Tester
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
product
Portable Hydraulic Testers
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
product
Rockwell Hardness Tester
The QATM Rockwell hardness tester series combines sophisticated design with technical innovation. A wealth of comfort functions make operation easy, safe, and fast. Modern software and interfaces allow time-saving automation and integration of the hardness tester into any lab. Due to the large test force range, Rockwell testing can be carried out for many different materials.
-
product
Battery Impedance Tester
KVBT-15S
KV Hipot Power Test Equipment Co.,Ltd
Battery Internal Resistance Tester with advanced AC discharge measurement method, is applied to test accurately the voltage and resistance of battery capacity and state.
-
product
Insulation Resistance Tester For PV
MSEI-200C
MULTI MEASURING INSTRUMENTS Co., Ltd.
This model can measure insulation resistance of DC current circuit in PV systems (between PV module and power conditioner) on the live line and can distinguish the deteriorated part between Power Phase, Neutral Phase, P/N Phase and or PV modules.
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable. The LAN cable tester can verify cable continuity, open, short circuit and miss-wired. The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels. Auto and manual scan functions. Ground wire test. Lock status function. Buzzer sound warning for wire status. Display : LED indication for wire status.
-
product
Universal Wear Tester
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. This Wear Testing Machine complies with ASTM D3514/D3885/D3886, AATCC 119/120, FTMS 191/5300/5302, etc.
-
product
Electrolytic Capacitor Leakage Current Meter
TH2686N
Changzhou Tonghui Electronic Co., Ltd.
■ Test voltage: 0-200V, 0-500V ■ Voltage accuracy: 1% set value + 1 word ■ Measuring range: 10nA-19.99mA, resolution: 1nA ■ Current accuracy: 2% reading + 2 words ■ Intelligent type, microprocessor control
-
product
Unclamped Inductive Load Tester
ITC75300
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
product
-AC/DC/IR Hipot Tester
Sentry 30 Plus
Wuhan Fanke Transformer Manufacture Co., LTD
Sentry 30 Plus - AC/DC/IR Hipot Tester
-
product
Automotive Engine Tester
QCM-2A
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to integrated test varieties of automobile motor, wiper motor, window lifting motor, oil pump motor etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stators.
-
product
Portable Electricity Meter Testers
EE-120A-3S + EE-500V-3
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Starting Current Test. Full analysis of the customer load can also be performed, if current clamps have been ordered. All test results ( maximum 3 Test Plans, 5 Manual Measurements and Customer Load Analysis) can be saved in one file. 100 saved files can be viewed on the LCD display or transferred to a PC via USB port.
-
product
Pin Brinell Tester
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
-
product
Mobile Network Tester
Qosmotec Software Solutions GmbH
The main motivation for a subscriber to select a mobile network operator are the costs and the quality of the cellular network. Network coverage, reliability and performance are the key factors for customer satisfaction and influence many subscribers’ decision for service provider change. Qosmotec’s Mobile Network Tester LTS verifies the user experience of the mobile network for all relevant network applications and services and provides key performance indicators (KPIs) to assess the network quality.
