Corrosion
gradual degradation of a material over time
See Also: Salt Spray, Salt, Salt Fog, Corrosion Test
-
Product
Corrosive Series Valved Cracker
-
With the superior flux control of the Corrosive Series Valved Cracker, complex structures not possible with conventional thermally controlled sources can be achieved. Mixed Group V layers of varying compositions can be grown without the frequent recalibration procedures necessary when using standard sources. SIMS analysis of a continuously graded GaAs1-xSbx layer demonstrates the excellent flux control available when using two Group V valved crackers, with identical results achieved at two different growth rates.
-
Product
Troposcatter Antennas
-
Kratos Defense & Security Solutions, Inc.
Troposcatter antennas consist of a reflector structure, feed assembly, and support. Reflectors are precision-formed by aluminum spinning to maintain extremely accurate contour and high performance. Back structures are hot-dip galvanized structural steel. All aluminum parts are corrosion coated and painted.
-
Product
Bimetal Thermometer
BT
-
Series BT Bimetal Thermometers offer accurate, reliable service even in the toughest environments. These corrosion resistant units are constructed from stainless steel and are hermetically sealed to prevent crystal fogging.
-
Product
Mass Flow Controller for Medium Flow
HFM-201 / HFC-203
-
The HFM-201/HFC-203, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-201 / HFC-203 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Many corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Type 12R1 Family of 19" Rackmount Chassis Platforms, Reduced Weight, Rugged
12R1
-
The Type 12R1 family is a 19" rackmount chassis platform that is rugged yet lighter weight than the sturdier Type 12R2 platform. The chemical conversion coating provides corrosion protection and electrical conductivity. The rear evacuation cooling system uses high CFM blowers to remove the heat generated by the board payloads.
-
Product
CORROSION GAUGE
MX-2
-
The MX-2 is ideal for the person that tests a few different materials regularly. The MX-2 contains 8 velocities of common materials and two velocities that the user can set using a simple sofware program. The tool's backlit display is easy to read, even in dim light, and the unit operates for up to 200 hours on a single set of batteries. The MX-2 comes complete, ready to use, and is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
ISO Scratching Tool
1537
-
The Elcometer 1537 ISO Scratching Tool is a simple but effective instrument that is used to scratch the surface of samples in preparation for adhesion, salt spray and corrosion tests.
-
Product
Environmental Testing Equipment
-
It is to do adaptability and properties test for materials under different environment conditions, which includes salt spray test to determine corrosion resistance and temperature and humidity chamber to do a variety of high-low temperature alternating test.
-
Product
Ultrasonic Flowmeters
-
Clamp-on type sensor easily mountable on existing pipe Suited for a wide range of liquids, for example, deionized water, cooling water, chemical solution, drinking water, sea water, oil, tap water, hot water, industrial water, corrosive liquids. Ultrasonic flowmeter for air is also available
-
Product
Buried Pipes and Steel Structures Testing Equipment
-
Buckleys now offer a range of products suitable for the inspection and monitoring of corrosion in buried pipelines and steel structures.
-
Product
Electrochemistry
Portable Line
-
Portable Line potentiostats/galvanostats combine electrochemical research in the laboratory with on-site research using well-established electrochemical techniques.These small and affordable portable instruments enable you to develop applications for your specific research needs. Portable Line instruments are an ideal solution in many research areas, such as (bio)sensor, corrosion, or (bio)fuel cell.
-
Product
CORROSION GAUGE
MVX
-
The MVX finishes the line of MX gauges with class. This thing is loaded with all of the features of the MX gauges and a lot more. Four selectable display options: RF, Rectified, B-Scan, and Large Digits. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and auto waveform find just to mention a few! Equipped with a single element flaw prove-up mode for basic angle beam inspections. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVXview java-based PC software makes this thing a complete kit, and then some!
-
Product
Coupled Multielectrode Array Sensor (CMAS) Probes
-
CMAS probes are made from user-specified sensing materials, including carbon steels, stainless steels, and nickel-, aluminum-, and copper-based alloys. They can also be made from customer supplied materials that have the same microstructure/heat treatment as the system component materials to be monitored. The size of the sensing electrode varies from 0.1 to 3 mm (0.004" to 0.12") in diameter, depending on the application. Typical numbers of electrodes in a CMAS probe are 9, 16 or 25 for online corrosion monitoring and vary from 8 to 100 for laboratory corrosion and electrochemical studies.
-
Product
Ultrasonic Thickness Gauges
-
Used for measuring thickness and corrosion of pressure vessels,chemical equipment,boilers,oil storage tanks,etc.in industries of petroleum,shipbuilding,power station,and machine manufacturing.
-
Product
Dissolved Ammonia Delivery System
DI-NH3
-
MKS' DI-NH3 is a compact, stand-alone system providing dissolved ammonia water. With Semiconductor 3D IC architectures using new materials like Cu-Co and Si-SiGe, the ability to wet clean with precise alkaline chemistries is growing in frequency and importance. The DI-NH3 delivers dissolved ammonia, providing optimal cleaning capability in an alkaline chemistry, minimizing material loss and contamination and inhibiting Electrostatic Discharge (ESD). Using closed-loop control, conductivity and pressure are kept stable under changing flow conditions. The dissolved ammonia concentration is monitored and adjusted, delivering the specific NH4OH concentration needed. Dissolved ammonia’s alkaline chemistry provides ESD protection during rinsing, particle lift-off, and residual photoresist removal in middle-of-line (MOL) and prevents corrosion of cobalt/copper interfaces.
-
Product
Linear Polarization Resistance Probes
-
Linear polarization resistance (rosion probes are commonly used in the water treating industry and other environments where instantaneous, on-line corrosion rate readings are required. Linear polarization probes are ideally suited to monitor fluctuations that may occur within a system; for example, these probes can be used to monitor corrosion inhibitor effects on a regular basis.
-
Product
Electrical Resistance Probes
-
Electrical resistance (ER) corrosion probes are commonly used in petroleum, chemical processing, and other environments where on-line corrosion rate readings are required. Whereas test coupons must be removed from the process for evaluation, corrosion probes can allow corrosion rate determination without probe removal.
-
Product
DIN Scratching Tool
1538
-
The Elcometer 1538 DIN Scratching Tool has interchangeable carbide cutters for the preparation of specimens to be used for corrosion testing.
-
Product
Syringe Pump
500x
-
The 500x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter up to 204 mL/min. Exceptional low-flow stability at up to 5,000 psi (345 bar) makes this the ideal pump for high pressure applications from deep well core analysis to a wide range of chemical applications.analysis to a wide range of chemical applications.The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 500x pump module has a single-ratio drive train with auto-lubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. Hastelloy cylinders are available for chemical compatibility of corrosive solutions. Single and continuous valve packages are 100% Hastelloy for full compatibility. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
Product
Moisture Analyzers
V-Series
-
The MIDAC V-Series is designed to detect lower moisture levels than ever before...so you can raise your standards for purity higher than ever before! It's true, MIDAC's V-Series Moisture Analyzers provide unprecedented capability for detecting moisture and other impurities in corrosive gases.
-
Product
Meter Test Switches
-
TESCO introduced the original Meter Test Switch in the early 1920’s. Today, TESCO’s line of Test Switches has been redesigned with the intention to combine the best features of tried and proven switching methods with improvements in materials and construction. All of the current carrying parts are bright tin plated to prevent corrosion. Good operating contact is assured on periodic meter tests, even when the switch has been idle for long periods of time in an unfavorable atmosphere.
-
Product
Tipping Bucket Rain Gauge
HD2015
-
The HD2015 is a reliable and sturdy bucket rain gauge, entirely constructed of corrosion resistant materials in order to guarantee its durability.
-
Product
CCX Advanced Cyclic Corrosion Cabinet
-
Atlas Material Testing Solutions
The CCX is the most advanced, sophisticated and versatile laboratory corrosion testing cabinet. With installed options, it can replicate up to 15 environmental conditions, placing powerful capability in the hands of the user.
-
Product
Exhaust Gas and Wheel Space Thermocouple
EGT
-
AMETEK Exhaust Gas (EGT) and Wheel Space Frame Turbine Thermocouples meet the specific operational and performance requirements for REPLACEMENT and RETROFIT Frame gas turbine applications. AMETEK's expertise in solving creep, stress, rupture, corrosion, EMF drift, and other problems affecting sensor performance has resulted in a robust line of single and dual element thermocouple designs. Typical applications include wheel space and exhaust gas temperature monitoring.
-
Product
Flow Wet-Tap Valve
3519
-
The Signet 3519 Flow Wet-Tap Valve serves as a unique interface between the installation fitting and the wet-tap style Signet 515 or 2536 Rotor-X Flow Sensor. It provides a fast method of removing the sensor from the pipe under specified operating pressures. The PVC and stainless steel design of Wet-Tap makes it resistant to corrosion and chemical attack by acids, alkalis, salt, and a number of other harsh chemicals.
-
Product
Portable Sulphuric Acid Dewpoint Temperature Monitor
-
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
Product
SF Walk-In Series Corrosion Cabinet
-
Atlas Material Testing Solutions
The SF Walk-In Series are rugged and reliable traditional salt fog (spray) and humidity cabinets. In addition, they can perform basic wet/dry cyclic and condensing humidity tests when properly configured. Custom sizes and dimensions are available.
-
Product
6 Pin Round Pin Tester / Maintenance Kit
#8027
-
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
Product
Computational Fluid Dynamics
CFD
-
Computational Fluid Dynamics analysis is a value-added service from Teledyne Cormon that predicts pipeline flow and sand particle behavior for specific project scopes, allowing asset integrity teams to understand the optimal placement for erosion and corrosion monitoring probes.
-
Product
Needle Valves
-
Needle valves are designed for laboratory and industrial applications for regulating corrosive gases and liquids or for high purity service. They can also be used as bubble tight shut-off valves.
