TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
Broadband Power Amplifiers
-
Our range of broadband power amplifiers are designed using the most suitable devices and techniques. We don’t believe in following fashion in our choice of parts, but will continue to use older technology where it is still the best, and incorporate the new where improvements can be made.
-
Product
Optometers, Amplifiers, Display Meters
-
Optometers are a specific type of digital multimeter (DMM) used for optical radiation measurements. The particular light detector(s) connected determine the wavelength range/spectral weighting function and displayed measurement units.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Digital Quad-channel High-frequency Lock-In Amplifier -
eLockIn 204
-
Digital quad-channel high-frequency Lock-In Amplifier.
-
Product
HF Amplifier
Prometheus
-
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
Product
Microwave Power Amplifier 1/4 Watt 10 MHz to 50 GHz
GT-1051B
-
The Spanawave/Giga-tronics GT-1051B Microwave Power Amplifier offers linear high-power amplification across muultioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
High Speed Amplifier
-
TI offers the industry's most comprehensive high speed amplifier portfolio with the widest bandwidth and best in class distortion, precision and power consumption across a broad range of supply voltages. Our industry leading FDA's, DVGA's, TIA's and General purpose amplifiers coupled with the reliability and longevity of our parts makes TI the ideal supplier of high speed amplifiers.
-
Product
Millimeter-Wave Amplifiers
-
When your application requires operating at Ka-band and above, trust Mercury Systems’ millimeter wave amplifiers to perform. With standard designs up to 65GHz and custom products available, Mercury is ready to support your high frequency requirement.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
Product
Booster and In-line Amplifier
-
Amonics' EDFA range adopts unique design to produce maximum signal gain and saturated output power while maintaining low noise figure, enabling test capabilities in system or component level manufacturing and characterizing processes, as well as facilitating highly demanding R&D applications. The compact turnkey benchtop or 19" rackmount unit incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power control knob and optical connectors. An integrated RS232 computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
Power Amplifier, RF
-
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
Product
High-end Cable DAC & Amplifier
Impacto essential
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Amplifier Module
LNAM-LPA
-
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
Product
Wideband Distributed Amplifiers
-
A wideband amplifier has a precise amplification factor over a wide frequency range.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Testing)
PA60Bi
-
PA60Bi is the panel-mounted power amplifier, which can produce 3-phase current, with maximum RMS phase current of 60A and maximum output power of 800VA, and 4-phase voltage, with maximum RMS phase voltage of 120V and maximum output power of 60VA.
-
Product
Voltage and Current Amplifier
CMS 356
-
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
-
Product
6-Channel VME Pulse Amplifier
V860
-
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
Product
Linear Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOMs linear amplifiers offer high IP3, power up to 2.5 W and are offered in a variety of DIE and package types to simplify point-to-point wireless, SATCOM/VSAT, and radar system design.
-
Product
H2S Trip Amplifier Module
TA202A
-
The TA202A is a single-channel H2S Trip Amplifier Module for use with our H2S Intelligent Sensors. It is designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
-
Product
Signal Amplifier
ZET 410
-
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Receiving Amplifiers
-
he products from Kuhne electronic from the category "Receiving Amplifiers for Professional Use" are designed for the following applications: Radio Link Systems, Satellite Receivers as well as Scientific and Measurement Instrumentation.These amplifiers stand out due to outstanding Noise Figures as well as a very good Large Signal Stability and small Housing Sizes.
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Ultra-small / Cable Type]
PM-25
-
Panasonic Industrial Devices Sales Company of America
The Panasonic PM-25 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1mm thereby reducing the possibility of sensing objects colliding.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
