Cages
-
Product
37-Pin D-Type Female Connector Block
40-965-037-F
Connector Block
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
96-Pin Micro-D Connector Block, Female With Screwlocks
40-965-096-F
Connector Block
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
200-Pin LFH Connector Block, Male
92-965-200-M
Connector Block
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure that appropriate electrical safety precautions are observed.
-
Product
Crowbar Resistors
-
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
Product
Antenna, Biconical
EM-6912A | 30 Mhz – 300 MHz
-
A balun, feedline, and element cage give the Electro-Metrics EM-6912A response curves that are almost linear, making it ideal for swept measurements. An added benefit is that the EM-6912A has an improved BALUN design, which makes it insensitive to changes of orientation while vertically polarized. Readings obtained will be the same no matter which element is closest to the ground plane, eliminating a potential source of measurement error.
-
Product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Vertical
12R2-8U-V
-
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
VME Test Extender 6U/220mm 64X with P0
116EXT6122-0125R
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Type 12R2, 9U, 19" Rackmount, MIL-Rugged, Vertical
12R2-9U-V
-
The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
160-Pin DIN41612 Connector Block, Male
92-965-160-M
Connector Block
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
Single Truck Steri-Dry™ Sterilizer
-
The Gruenberg Steri-Dry™ Dry Heat Lab Animal Science Sterilizer provides the lab animal science market with equipment to sterilize habitat cages through the process of dry heat sterilization. These sterilizers are designed and built for lab animal science applications.
-
Product
RF Shielding Services
-
LBA offers complete architectural RF shielding capabilities, including RF shielding for communications, medical and other radio frequency interference sensitive facilities. LBA is a major provider of architectural shielding solutions for buildings, laboratories and other spaces. LBA also offers other RF shielding materials, such as paints, fabrics and faraday cages, as well as an integrated line of shielding components to provide a comprehensive shielding system.
-
Product
CompacFrame Type 39A, up to 5 slots, VITA 48.8 AFT
Type-39A
-
Elma’s all new CompacFrame platform accelerates the development and test of 3U plug-in-cards (PICs) designed according to VITA 48.8, Air Flow Through Cooling standard. The 3U card cage in the platform is tilted upwards by 5° for easier card access.
-
Product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
68-Pin VHDCI Connector Block, Female With Backshell
B068VFR-6F-0A
Connector Block
This connector block provides a simple method of connecting to high density 68 Way VHDCI connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
96-Pin Micro-D Connector Block, Male With Backshell
40-965-096-M
Connector Block
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
2-in-1 High-Voltage Test Hood
LX-HVE900EC
-
The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate in the test cell - optionally with an interchangeable interface or an interchangeable adapter cassette - allows quick adaptation to different types of test items. Prepared openings enable connectors and other common interfaces or cable bushings to be easily attached. The hood is opened and closed almost effortlessly thanks to precisely coordinated gas springs.
-
Product
68-Pin SCSI Micro-D Male Connector Block
92-965-068-M
Connector Block
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
96-Pin Micro-D Connector Block, Female With Backshell
44-965-096-F
Connector Block
This connector block provides a simple method of connecting to high density 96-Pin SCSI Style Micro-D BRIC connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
High Speed Caged Ball
SBK
-
High Speed Caged Ball Ball Screw. THK high speed caged ball ball screw type SBK that eliminates collisions and friction between ball and prolongs the effectiveness of grease by utilizing the caged ball mechanism. This mechanism reduces a noise level, torque fluctuation, and a long maintenance-free period.
-
Product
VME Test Extender 3U/400mm J1
111EXT3140-11xx
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
VME Test Extender 9U/220mm J1/J2/J0
111EXT9122-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
2-in-1 High-Voltage Test Hood
LX-HVE600EC
-
2-in-1 high-voltage test hood with integrated interchangeable setHV hood for electrical safety test & function test.The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate in the test cell - optionally with an interchangeable interface or an interchangeable adapter cassette - allows quick adaptation to different types of test items. Prepared openings enable connectors and other common interfaces or cable bushings to be easily attached. The hood is opened and closed almost effortlessly thanks to precisely coordinated gas springs.
-
Product
Mu-Copper Faraday Cages
-
Holland Shielding Systems B.V.
Mu-copper foil is used to create a Faraday cage in an existing room or building.
-
Product
68-Pin VHDCI Connector Block, Female Without Backshell
B068VFX-6F-0A
Connector Block
This connector block provides a simple method of connecting to high density 68 Way VHDCI connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
96-Pin Micro-D Connector Block, Female Without Backshell
92-965-096-F
Connector Block
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
160-Pin DIN41612 Connector Block, Female
92-965-160-F
Connector Block
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
Industrial I/O Module
DIO-3460
Digital I/O
The DIO-3460 is a space-saving industrial I/O module. It provides for save cable connections due to the use of WAGO Cage Clamp connectors rather than screw terminals.
-
Product
Cell Stand
CS-3A
-
The CS-3A Cell Stand is adopted with CHI series Electrochemical Analyzers and other apparatus directly. The cell is enclosed in a Faraday cage to reduce electrical interference. A built-in gas control allows purging a sample. Gas line is provided to purge next sample, while analyzing the present sample separately, thus increasing productivity. Magnetic stirrer allows for controlling the mixing of the sample for experiments requiring mass transport of electrolyte or analyte to the electrode surface. Cell top positioner with detachable cell cap allows easy removal and replacement of the cell vial as well as the electrodes for rinsing, cleaning, and replacement.
-
Product
ARINC818 Cards
-
> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.
-
Product
Electric Burn-in Board Carts
-
Conforms to SEMI ergonomic standards Holds and transports card cages for semi-automatic loading/unloading. Holds up to 10 burn-in boards. Raises and lowers the burn-in boards for easy loading/unloading of boards into ovens or onto test benches. Cart can be adapted to dock with any Micro Control oven.
