Cards
See Also: Extender Cards, Probe Cards, POST Cards, Test Cards, Boards, Modules
-
Product
PMC Carrier PXIe x4
-
Looking for a way to plug your PMC mezzanine card into a computing platform with a 4-Lane PXIe slot?Well, the CC_PXIeG1x4_to_PMC is your answer! It is effective, field tested and compliant with all applicable standards.
-
Product
FMC-LPC I/O Module
FM191
-
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
Product
Serial-to-Daq Card
Model 2307
-
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Product
Satellite Modulator For PCI
DTA-107
-
DekTec's first modulator card. At release the DTA-107 supported DVB-S, while in a later stage DVB-S2 was added. The card performed (and performs) extremely well, as did sales, which outperformed our wildest dreams.
-
Product
Rear Cover, S6, Tabletop Configuration, For Part # 310 122 100
310113431
Protective Cover
The Rear Covers are designed to enclose the wiring that runs from the S6 Receiver on the tabletop to the instrument cards below. This rear cover is used with the S6 Receiver Part # 310 122 100.
-
Product
3U VPX Graphics Output Board
GR2
-
The Abaco GR2 is a 3U VPX graphics output card based on NVIDIA® Pascal™ Quadro® P5000/P3000 GPUs. The GR2 offers very high performance graphics and GPGPU capability – up to 6.4 TFLOPS floating-point - with CUDA™ and OpenCL™ support.
-
Product
PCI Express Optical Link Board
SIS1100-E2
-
The SIS1100-e2 is the follow up card to our SIS1100-eCMC board (without CMC carrier functionality). It was developed to extend the lify cycle of our PCIe to VME interface. For software/driver compatibility reasons we still employ the PEX8311 PCI Express to local bus bridge chip.
-
Product
ISA bus GPIB Controller Card
Model 488-PC2
-
* Adds GPIB Controller capability to any PC with an ISA bus.* Fast data transfer rate, > 300kbytes per second.* Drivers for MS DOS, Windows 3.1, Windows 95 and Windows 98. * IEEE-488.2 linkable libraries for Quick Basic, MS Visual Basic, Borkand C/C++ andMicrosoft C/C++.* Functions as System Controller, Controller-in-charge or a GPIB Device.* Replaces most generic ISA 7210 Cards and NI PC2a cards.* Includes interactive keyboard Control Utility for controlling instruments from the computer keyboard without writing a program.
-
Product
VME64x 7U 84HP 17 Slots
-
Hartmann Electronic’s 17 slot 19” rack mountable VME solution – The VME64x 7U system. This VME chassis comes with two 400W cPCI hot-swap power supplies with vertically oriented card slots. This platform conforms to VITA 1.1-1997 while providing a high capacity yet practical packaging solution for high-performance processors.
-
Product
Digital Signal Processor Card
CHAMP-AV8
-
Curtiss-Wright Defense Solutions
The CHAMP-AV8 6U OpenVPX digital signal processor (DSP) combines the floating-point performance of the 3rd generation Intel Core i7 processors with the substantial bandwidth and system-enabling features of the 6U OpenVPX form factor. Utilizing a pair of 2.1 GHz quad-core processors featuring the Advanced Vector Extensions (AVX) instruction set, the CHAMP-AV8 DSP card delivers up to 269 GFLOPs.
-
Product
20mA/RS232/422 Strobe Mux III Card, Panel & Power Supply
9565-32CPP
-
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25mm).
-
Product
SWB-2815, 4x86, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-15
Reed Relay
4x86, 0.3 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PCI Reed Relay Card, 64xSPST
50-115B-121
Reed Relay
The 50-115B-121 is a 64xSPST PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
USB DAQ
-
ADLINK USB DAQ modules leverage the expertise of ADLINK's analog design capability, enhancing convenience of data acquisition. Simply plug the ADLINK USB DAQ into a USB port on your computer or notebook for performance equaling or even exceeding that of ADLINK PCI/PCIe DAQ cards, with no need to power down or open the chassis. As well as providing basic voltage measurement, ADLINK USB DAQ modules feature built-in signal conditioning to directly receive measurement from most commonly used sensors, with no need for extra signal processing. From basic testing to high-accuracy measurement, from portable application to industrial automation, the ADLINK USB DAQ series delivers easy, efficient, and accurate measurement every time.
-
Product
CompacFrame Type 39A, up to 5 slots, VITA 48.8 AFT
Type-39A
-
Elma’s all new CompacFrame platform accelerates the development and test of 3U plug-in-cards (PICs) designed according to VITA 48.8, Air Flow Through Cooling standard. The 3U card cage in the platform is tilted upwards by 5° for easier card access.
-
Product
PC-based DSP Systems
-
PCI / cPCI : 32bit, 33MHz6201 or 6701 DSP16MB SDRAM1MB SBSRAM15+ Mezzanine I/O Cards (see OMNIBUS)Open bus for custom I/OFIFOPort external data port
-
Product
Stepper Motor Controller for CompactPCI
CPCI322
-
The CPCI322 is a 3U CompactPCI card. The CPCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
CompactPCI 4 Slot 2U
-
2U, 19″ Rackmount system with up to two hot removable CPCI 3U Power Supplies, three Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional three fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz and supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot. A backplane supporting PICMG 2.16 & H.110 are available on request.
-
Product
PCI Precision Resistor Card 9-Channel, 1Ω To 122Ω
50-297-112
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5966-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
RF Test Benches
-
FIME laboratory equipment qualified for RF testingValidate the analogue behaviour of RF devices with a single set of laboratory tools and services before seeking contactless Level 1 type approval or launching mass production. FIME RF test benches are built for RF testing of: EMV contactless cards and readers; ICAO e-passports and readers; ISO devices (PICC and PCD), HF and UHF RFID tags and readers.
-
Product
64-CH, 12/16-Bit, Up to 3 MS/s Multi-Function DAQ Cards
DAQ-2200 Series
-
ADLINIK DAQ-2204, DAQ-2205, and DAQ-2206 are high-density and high-performance multifunction DAQ cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination The DAQ-2200 series also feature analog and digital triggering, 2-CH 12-bit analog outputs with waveform generation capability, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
Analog Output PXI Card
GX1642
Analog Output Module
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Data-logging Circuit Tester for PoE Power
-
The Log4 PoE displays accurate readings of voltage, current, and power while also simultaneously logging all measurement data to a MicroSD card and/or the free dedicated PC software. The Log4 PoE device is specifically designed to measure the low positive voltages of Power over Ethernet (PoE) connected equipment with high accuracy.
-
Product
PICMG 1.3 Full-size CPU Card With LGA1150 4th Gen Intel® Core™ I7/i5/i3 Processor, Intel® Q87, SATA3, USB 3.0, DVI-D, VGA, DisplayPort And Dual LAN
SHB130
-
The PICMG 1.3 full-size CPU card, SHB130, designed for the new architecture 4th Generation Intel® Core™ processors (codename: Haswell/Haswell Refresh) with Intel® Q87 chipset on 22nm technology using LGA1150 socket. The outstanding SHB130 with new Intel® architecture delivers up to double the graphics performance over the previous generation. The new graphics solution has high levels of integration to enable new form factors and designs with excellent visual quality built in. In addition, The PICMG 1.3 full-size CPU card comes with two DDR3 1333/1600 MHz unbuffered ECC DIMM slots up to 16 GB of system memory and six SATA 6Gbps ports with RAID 0, 1, 5, 10. The PCI Express 2.0 available on the new Intel® Core™ processor provides flexible x16, x4 or x1 lanes for versatile applications. The high performance SHB130 with improved graphics ability is ideal for applications such as network security, storage server, POS, kiosk, medical, gaming, digital signage, and surveillance security monitoring.
-
Product
WAN Adapters
FarSync T4Ue
-
The FarSync T4Ue PCIe card provide high performance 4 port sync communications support for Linux and Windows systems. A PCI version of the card is also available.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 470Ω
50-298-014
Programmable Resistor Module
The 50-298-014 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Quad ASI/SD-SDI Ports For PCIe
DTA-2144B
-
Industry-standard PCIe card for professional PC-based applications that require ASI inputs and/or outputs. Features include flexible receive and transmit modes, arrival timestamping and false-sync pass through for full TR 101 290 analysis.
-
Product
Fanless Embedded System With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 4-CH PoE And MXM 3.1 Type A
eBOX671-521-FL
-
The eBOX671-521-FL is a GPU computing embedded system that comes with 4-CH PoE and MXM 3.1 Type A slot for applications in machine vision, edge computing, traffic vision, deep learning, and artificial intelligence of things. The outstanding eBOX671-521-FL with enhanced GPU computing performance is powered by the 9th/8th gen Intel® Core™ i7/i5/i3 processor with up to six-core, Intel® Pentium® processor, or Intel® Celeron® processor and comes with Intel® Q370 or optional Intel® C246 chipset. The fanless embedded GPU-based system is equipped with dual DDR4 ECC/non-ECC SO-DIMM slots for up to 64GB of system memory. The embedded vision system has an optional MXM type A slot for NVIDIA GTX1030 and GTX1050 graphics modules to enhance the performance of the visual display. Furthermore, this Intel® Coffee Lake-based embedded box PC is specially designed with four Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports with a total power budget of 60W, six USB 3.1 ports and two Gigabit LANs to connect different devices or sensors. It comes in great expansion possibilities, including one internal MXM 3.1 type A connector, two full-size PCI Express Mini Card slots and two SIM slots. For storage, it has two swappable SATA HDD drive bays with a height of up to 9.5 mm and one mSATA for RAID 0 and 1 feature. Besides, we have designed a flexible I/O window slot for incorporating application-oriented I/O functions to meet the requirements of various cases. This embedded vision computer can be mounted using wall or DIN-rail mounting for versatile use in various environments.
