Cards
See Also: Extender Cards, Probe Cards, POST Cards, Test Cards, Boards, Modules
-
Product
SIMRC - 8 x 4 Matrix 1-Pole Screened Relay
1030-R-8-4-1RF-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
PCIe Basic Protocol Tx and Bus Monitor
Sy629PCIe-BPM
-
The Sy629PCIe-BPM card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory.
-
Product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
Terminal Block
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
Product
Power Supplies
ZPS-1600B
-
80Plus Silver Certified provides typical 88% efficiency at 50% of max load. The ZPS-1600B can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in 16 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
Extender Card
-
The IEEE extender card, referred to as board PWB1000281-03. Extender card to allow for testing and debugging of the chassis assembly. This board was originally an Intel design that Dynamic Engineering was authorized by Intel to re-create
-
Product
PCI Express Timecode and GPS Reader Generator
PCIEX-SyncClock
-
The PCI-Express time code reference timing card with standard options such as IRIG B and optional GPS receiver provides an extremely accurate time source to the PCI-Express bus.
-
Product
4-Channel DAQ Module
FMC176
-
Sundance Multiprocessor Technology Ltd.
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC176 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
3.5” Embedded SBC With AMD® RYZEN™ Embedded V1807B/V1605B APU, DisplayPort, 2 HDMI, LVDS And 4 GbE LAN
CAPA13R
-
The CAPA13R is powered by the onboard AMD RYZEN™ Embedded V1807B/V1605B processor with Radeon™ Vega graphics. The 4K embedded board is well-suited for graphics-intensive applications such as medical imaging, video surveillance, 3D simulators, optical quality control, digital signage, kiosks/POI, thin clients, and more. The integrated AMD RadeonTM RX Vega graphics with support of DirectX 12 and OpenGL 4.5 marks the cutting edge of embedded graphics. The CAPA13R can deliver truly impressive user experiences and outstanding 3D graphics quality through two HDMI, one DisplayPort and one LVDS interfaces. Its onboard CPU is attached on the rear side of the board, which can aid with heat dissipation and offers flexibility for easy system integration and minimum maintenance. Moreover, the CAPA13R offers multiple expansion interfaces with one M.2 Key E slot for wireless modules and one M.2 key B slot for storage cards. One 260-pin SO-DIMM socket on the CAPA13R supports up to 16GB of DDR4-2400 (V1605B) and DDR4-3200 (V1807B) memory. The system has a +12V DC power input.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 1.81kΩ
50-298-022
Programmable Resistor Modules
The 50-298-022 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Interface
RPCC-D1553
Interface
This dual channel card is RoHS-compliant and is a direct drop-in replacement for the PCC-D1553 card which it replaces. The RPCC-D1553 comes with all necessary cables for operation. Cables designed for the PCC-1553 card will not work with the RPCC-D1553 card. The RPCC-D1553 provides 1 or 2 channels integrated with powerful API software providing instant access to all MIL-STD-1553 databus functionality and data.
-
Product
PXI 4-Slot BRIC 48x8 Matrix, 2A 2-Pole (2 sub cards)
40-565A-002-48X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω to 925Ω
50-298-021
Programmable Resistor Modules
The 50-298-021 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Open Pluggable Specification (OPS) Digital Signage Player With Intel® Core™ I7/i5/i3 Processor
OPS875
-
*Open Pluggable Specification (OPS) compliance*Socket G2 (rPGA988B) 3rd gen Intel® Core™ i7/i5/i3 processor*Intel® HM76 chipset*DDR3-1600 SO-DIMM, up to 8GB*2 USB 3.0 ports and 1 PCIe Mini Card slot*Pluggable HDD for easy maintenance*Easy to change DRAM*HDMI for 2nd display
-
Product
Handheld Thermal Imaging Camera
Model TG 301
-
Kusam Electrical Industries Limited
•One Navigator Key Operation •16,384 pixels thermal image after interpolation•True D/S 30:1 with precise laser indication. •Bright flashlight with 5 white LEDs•Simple, Smart, Precise and Versatility. •160x128 pixel 1.77 inches TFT-LCD Display•Alkaline AA size x 3 Batteries•Key chain with wrist strap for carrying convenience•SD Card of 2GB is available.•Compact UV refrigerant leak detector with 5UV/Blue LEDs•Ergonomically designed pistol grip housing with excellent industrial Design
-
Product
256 Channel Power Supply
IDPS750
-
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
Product
PCI Relay Driver Card, 64-Channel
50-411A-001
Relay Driver
The card provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one terminal of a relay coil and the other terminal to an output of the 50-411A. Each output is capable of sinking up to 1A of continuous current.
-
Product
Spectroscopy Card
microDXP
Instrument Card
The microDXP is a complete, low power compact digital spectroscopy card design for a wide range of handheld, benchtop and other embedded applications, lowering cost and speeding time-to-market.
-
Product
Digital Signal Processor Card
CHAMP-AV9
-
Curtiss-Wright Defense Solutions
The CHAMP-AV9 combines the floating point performance of the Intel Core i7 processors, with the substantial bandwidth and system-enabling features of the 6U OpenVPX form-factor. Providing a pair of quad-core 4th generation Core-i7 (Haswell) processors, featuring the updated AVX 2.0 instruction units and redesigned on-chip graphics execution units, the CHAMP-AV9 offers a 2-4X performance per size, weight and power improvement over previous DSP modules.
-
Product
PXI Switching Instrumentation
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
Signaling Control and Monitor Equipment
MS 1303
-
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 472Ω
50-297-020
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
2/4-CH PCI Express® GigE Vision PoE+ Frame Grabbers
PCIe-GIE7x Series
Frame Grabber
- Hardware Trigger over Ethernet with Action Command- Up to 120W PoE power from PCIe bus/4-pin/6-pin Molex connector- PCI Express® x4 compliant- IEEE 802.3at for PoE+ (Power over Ethernet Plus)- PoE protection and automated power budget control for enhanced asset protection- Easy-to-use utility and API provided for PoE power management- Multiple cards, multiple cameras, in a single system- Wide operating temperature range from 0°C to +70°C supporting non-drop frame capture in extreme environments
-
Product
3.5" Embedded SBC With Intel® Celeron® Processor N2807, LVDS/VGA/HDMI, LAN And Audio
CAPA848
-
*Intel® Celeron® processor N2807 (1.58 GHz)*1 DDR3L-1333 SO-DIMM, up to 8GB*4 USB 2.0 ports*4 COM ports*2 PCI Express Mini Card slots and 1 SIM slot*1 Gigabit Ethernet port*LVDS/VGA/HDMI with dual-view supported
-
Product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
-
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
Product
PCI Express Mini Card
mPCIe-UCAN2 & mPCIe-UCAN2-ISO
-
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
Product
Embedded Graphics Controllers
-
Curtiss-Wright Defense Solutions
Whether you need a high-performance solution to see clearly in degraded visual environments or you're looking to add graphics processing without taking up another slot in your SWaP-constrained system, you'll find the perfect fit in our selection of embedded graphics cards.
-
Product
Dual 3U CompactPCI® Subsystem with Two 6-slot Backplanes and Two CompactPCI® Power Modules
cPCIS-2642 Series
Backplane
- Dual 3U CompactPCI® Systems, each with five peripheral card slots and one system slot- 1/1 250 W CompactPCI® Power supplies- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- PICMG® 2.11 47-pin power interface
-
Product
Economic DSP-Based 4-Axis Motion Control Universal PCI Card
PCI-1245E
-
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer for trajectory planning (circular trajectory and auto blending are not supported)Supports E-GearHardware emergency inputWatchdog timerPosition latch via ORG & index signalProgrammable interruptRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
M.2
-
a small, versatile, and high-speed physical standard for internally mounted computer expansion cards, most commonly used for SSDs.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 26.7kΩ
50-298-032
Programmable Resistor Modules
The 50-298-032 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 26.7kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
